Topman proper demo…

How to check the glow plug good or bad before removing ?

Merci beaucoup from to France 👍🏻

Good job mr Khan .from Philippines,

I am referring to the closing that you show at minute 2:30 . Gracias

Hello, a question, I have the same coolant tank, I have a water leak through the hose from the closing part that you show in the video (I have the same model), apparently the cable has no damage, do you know why this is, this happens in hot when I leave the car, thank you very much

There are two sensor b1 s1 and b1 s2 in which area should i place the cleaner

I always replace the copper crush washer when I change the oil. Some fill the filter with oil before installing it though I have not done that.

Did you fit a new gasket to the manifold, I have a Qashqai what engine was it.

Super thank you

Is hyundai accent crdi same as hyundai i30?

Afternoon mate, ill be looking to replace mine soon (old halogen bulb which aint lighting up much of anything) Any particular brand of bulb youd recommend?

Very interesting to see how you sow all the procedure.

Great video. Weird music What tool did you use to get the back 4 spark plugs out?

Hi where can I but the pipe?

My dream car i wish I had that

Advice from someone who’s been a mechanic for 20 years: Everyone wondering if they should try this… NEVER EVER use head gasket fixes. All of these additive type solutions create way more problems and cost much more in the long run. You WILL ruin any chance at having a basic head gasket replacement. I know that this car bills out at between 2500 and 3k for this service, but not only do you risk overheating and causing more internal damage, YOU WILL clog your radiator and heater core and damage your thermostat along with clogging up the coolant jackets inside the head. Trust me, you do not want to pay for a heater core replacement in these vehicles, labor will cost nearly as much as the head gasket job.

Legend

Thanks bro 👍

Morning Sir after someone changed my rear pads the electronic hand brake light is off but it's still working any advice thanks again

How do you fix this

Supperrr

Excellent video sir. Personally, I would not have tightened one slide pin before the other pin was properly engaged and running smoothly into its thread in the carrier. Well filmed. Best wishes.

Great little fix, the plastic clips always seem to break. What are the metal clips called so I can find them on TS website.

W homie appreciate the help g I woulda been so cooked if I didnt see this video. W homie

Your putting that dpf cleaner in the catalytic converter? The dpf is after the catalytic converter and has the pressure pipes pre and post dpf!!!

thank you. 😊amazing video.

I nearly done the same thing on my 1.4 TFSI when I watch ths video. I didn’t have the drain plug tool but I used screwdriver WITHOUT damaging the plastic drain plug 🪛 😂

Car refused to start this morning..i watched this video for 15 seconds and fixed it. Thanks!

Fuse brakes light for Toyota verso2006

i need part photo

Thank you very much for this video made it so easy to do

Could have shown how to breath it 🤞

Great video thank you 🤝

Changing this on the wife's car at the weekend - You made it look easy - Thank you for sharing it.

Please hindi language

Thats a m32 box. No wonder. Probably from bearing failure

hi, is it still working?

What's the socket size you used to remove the oil filter?

How did u get to that point

This was great, but how do you disconnect the fuel ine feed from the injectors? I want to attach a make device so I can spray car cleaner into the injectors via the fuel line feed, so I don;t have to take the injectors out at first. Thanks again,

My lense came off in bits the black edge stick in the groove ! So annoyingly stuck 😟

What sizes are they?

Thanks

Very well explained. Thank you 👍

U have to put fuel toll is full to start easily

Never clean it with brakecleaner !!

Thank you this will help all of us with the p3 model earned a like and subscribe!👍🏽

do you turn the 10mm bolt left or right i’ve been trying for hours and its just stripping on me

Why didnt you just buy the Oem Delphi part ? its not worth to install some cheap aftermarket crapp, especially when it comes to oxygen sensors !