No fuel left in the tank?? I thought the whole purpose of using nipples was to keep all the fuel in the tank.

Thanks for your video men

Muchas gracias, súper claro el video y bien explicado .

It has two jets

how to change washer fluid nozzle? 2019 qx80

I'm too deep to get out, I've fallen and I can't get up

My speedo is counting fast, I got no clue why 😂

Do u need to hold the bike level to check it or on the side stand?

Flagged!

Hi,how first drive?

After you disconnect the battery the truck is still running, do you hit the stop button after to turn motor off?

Wow

I think they look great I’m fixing to do the same with my 86 K10

What size of tires and wheels do You have bro?

What about in cemeteries where people rest that have not been "experimented on" or "va¢¢inated"?

Don't pacemakers utilize Bluetooth tech for follow up and maintenance and system analysis so the docs know what's going on? Maybe to answer my own question, wouldn't they remove such devices upon death anyways?

Thank you it worked perfect

Hey thank you! Hope after all these years you can still respond. How'd you get the cover to budge. I'm around 3:33. I loosened the peg but I can't pull this off lol

People do have a lot of lack of knowledge, the oil Literally Says GM Dexos D on the product datasheet.

Good info, just wish you had better video quality

Transfer case has 3 plugs. Bottom drain. lower small plug is fill level. Top hole is fill hole. You overfilled it.

Ahh common!!

Yeah my driver’s side temperature actuator is clicking, how do I fix that on my Infiniti

You didn't drain the transfer case and likely over filled it if you took it to the level of the fill port. The plug you removed from the transfer case that you called a drain plug is the level plug. There is a plug on the very bottom of the transfer case that takes a small hex wrench to remove. That is where you drain the transfer case. The other small plug that takes a 13mm or 1/2 inch wrench is the level plug. After you reinstall the drain plug you use the 1/2 inch plug to determine the fill level. If you fill to the level of the fill port you have over filled the transfer case. Good video but inaccurate information on the transfer case. Also it's best to remove the skid plate and clean up the bottom of the RZR.

No video on removing the seal or putting it on....the most important parts.

Why not just install a disconnect switch instead of removing it off the post

What the fuck??

Nice! At this point I’m my build also

You didn’t even shows how to do it all you did was point

Thank you for sharing this gem.

Do you use an auxiliary brake with this setup?

We also text vehicle before we disconnect the battery. However when we place from drive to reverse we do get “grinding “ noise. I don’t think this is good for transmission/transfer case. Is it safe to say that this “extra” test is not necessary?

Can you hear the sound of a small spring when the suspension is in operation? I have this on my Tiger and I'm not sure if it's normal.

The best video to show you nothing about removing or replacing the AC compressor. Already removed when the video starts and never puts in the new one.

It had a dip stick... now I feel like one as I've been looking for a sight glass... thanks for the info

To make it easier loosen the lower ball joint and take out shock bolt then you can lift the hub with the upper ball joint out of the way and get the cv out much easier that way and no real struggle compared to taking each ball joint nuts off.

Is there any hack to just forcing the air go out dash/face vents only? Mine is only blowing out floor and defrost vents. I don't think i have ability to remove everything you did to replace it. But if there's a way to rig it to only go out dash vents I'd appreciate any feedback or tips. Thank you.

THANK YOU! i got a Nissan titan I thought there were only two actuators .....no I got to look!

Good video! Only thing is that .05-.07 is a huge difference between .005-.007!

After reconnecting battery the horn goes off . Turned off with key fob but when door was opened horn goes off again. How do you make it not do that?

Great attempt but I thought it was odd that someone asked you to adjust the timing and you had no idea how to do it,so you checked you tube..

There is a hole behind the flywheel. Actually its just above the flywheel that you can get to that bottom starter bolt with your long allen socket.

You can buy the gasket from the dealership. To change the filter, you have to replace the valve body (straight from the dealer).

Thank you so much Mike!

What were the torque specs for thise bolts or did you just tighten and give it the qtr inch bump??

I thought this was a how to video. You showed what you did, but not how. You know, like the actual action of removing the jets

Thanks for the video. In your video you mentioned there are 2 blend actuators on the driver side. You discussed the vent actuator that does the hot / cold air mix. There is another blend door by the accelerator pedal. Can you explain what function for that blend door actuator?

Thank you this is going to help me so much now that I watched your video your awesome

Suck out the tranny fluid from the dip stick. Measure and replacd with 100% synthetic quality fluid. Consider amsoil 75w110 for rear diff.. if it doesng have a drain plug suck out from fill plug..

Before you fired this beast, why not put wd40 in cylinders if it hasn't been running for some time 🤔 I cannot believe you didn't change the fuel didn't you say it hadn't been running for some time?? I am looking for the put back together,. 🙄namely the adjustment back to the original for the float and or other, as I know I have messed around with adjustments and not sure where to set it.. Could have been a much more informative video...