@@rayartus5975 send us a message if you want other contents featured.

@@rayartus5975 Thank you for the support!

Hi Mike! The videos are usually made in English so it could reach all learners around the world. There is an option for the viewer to translate the transcript though, kindly check your video setting and choose subtitles for Greeks. Thank you very much for your interest on the video, I hope it helps, one way or the other.

​@@marineengineering1O1Yes, I don't disagree. I just noticed in the subtitle selection that Greek is not included.

Oh, is that right. I'm really sorry as I am not familiar with the greek language, I only use English to at least reach more seafarers globally. You seem to speak good english anyway, I hope you still get to pick up the good points on the videos. If you have any concerns and questions on the parts you missed, just message and will try to explain further. Nonetheless, I appreciate your support, thank you!

Anyway, thank you for your good mood and much more for your kindness to transmit through your channel the knowledge to every fellow Engineer. I greatly appreciate those who love to share their knowledge with colleagues, either to advance and develop knowledge or to make their colleagues' professional lives easier. As long as you allow me in advance, in case I need any explanation or advice or opinion I will ask you directly. I send you my friendly greetings​@@marineengineering1O1

Thanks! Full tutorial on our KZbin Channel. Hope you find time to watch. Thank you!

Thank you for the support!

@@lemuelcabungcal5083 collab ulit soon!

yes, we usually fill up the filter with oil before installation. Thanks for the feedback ;)

Thank you for your feedback!

For that type, that's how we made the disassembly. Hope it helps, let me know if you tried other options with this pump. All the best!

Yes today I overhauled the pump and tried out successfully. But during overhauling found shaft become little thin in the area near mechanical seal so i replaced whole motor. Thanks to spare motor we have.

Nice! Good for you. Getting expert with pumps! Keep rocking!

Ours looks fine. Maybe way too much air during starting.

Send us an email at [email protected]

Merci pour votre commentaire. vous pouvez sélectionner la traduction anglaise tout en regardant la vidéo.

Hey, Thanks for the suggestion! Will certainly reconsider this. Keep safe!

Sorry for the late response. It must be from the worn friction pads. Or broken flat belt.

Hey' Find the valve that controls the back pressure. It is the one with the Allen key adjusting knob. Forgot the specific valve number but that's how we adjust the feed rate. You can also try to adjust the manual inlet valve to control the flow.

Like most sight glass, it is for engineers to be able to carry out visual inspection in cases of leak. :)

@@marineengineering1O1 thanks for ur reply 🙏

@@mec6953 Thanks for taking interest on the videos posted here. Your feedback helps in content creation as well. God bless.

It was on long standstill and when the engineer on the watch changed the service compressor it broke down. Later on, it was discovered that the lube oil on the sump tank was very dirty. It could have been the build up of sludge that broke it. Unloader valve was checked and was working fine.

Some designs have cooling muffs to make sure that the rubber impeller doesn't run dry, overheat and become brittle. When the rubber impeller on the cooling system is worn out, there will be no more cooling supply. Hence, always run submerged in the water. Will compile the videos for our impeller replacement job and tag you again. For the meantime this one. Thanks. kzbin.info/www/bejne/m5CkgaybZtx0iMU

@@marineengineering1O1 many thanks

Geeez Thanks! Your inputs and suggestions have been helpful. I'm doing reels on Facebook, more micro contents with English subtitles and audio. Nonetheless, thank you for always checking out. Do keep in touch!

Hindi kaya pressure transmitter?

Feedback error meaning yung pressure transmitter mali or walang signal na binibigay, baka electronic trouble.

Correct. We need correct separation temperature only that for this purifier tutorial , we were having MGO since we are in ECA, hence no heating was required. Will try to make new one on HFO. Thanks!

You could your operating water, maybe the pressure is not enough. Sometimes orifice of valve block water gets clogged.

Will try to do that soon. Thanks

Setting in terms of temperature? Makikita sa bunker analysis. Dun kasi naka depende ang treatment ng oil. Check your bunker lab data and dun ka mag base sa requirements. Thanks for dropping by.

Pressure transmitter fault

Could you check if there's a valve with an allen key that you could use to adjust the PT4? Usually if this valve is not properly calibrated some problems with PT4 happens.

If I am not mistaken the valve is VA4 or V4. It is a pneumatic valve that you could calibrate via allen key.

what is pt4 you know?pls say m

PT4 if Im not mistaken is the backpressure. You could adjust through put or rate of feed/hr by regulating the valve.

@@marineengineering1O1 yes things have been sorted out. The 3-way valve was not operating as the air block was non responsive..

Thank you.

Tama ,manual opening and closing ng water flow yan. Usually kapag mag trouble shoot ginagalaw natin yan (Open/Close) to check kung may flow ang operating at sealing water.

@@marineengineering1O1 ano po kaya dahilan ng high oil pressure? brake po ba sagot kapag high vibration?

@@thishandleisntavailble444 high oil pressure baka blocked ang fuel line or may close na valve. Kapag heavy vibration yes kailangan i apply ang brake. Pero pagkatapos kailangan check baka hndi na okay ang alignment ng bearing kaya malakas na mag vibrate or baka imbalance na dahil madumi na ang disc stack.

There is probably another interlock alarm that was not reset. Check the relays maybe or some contactors not properly reset.

Thank you sa feedback. Buti at nakatulong :)

Hello JM. I started MDO Purifier. Trading route is in EU so DO ang gamit na fuel.

OK sir, sana po makapaglabas din po kayo ng video about How to start the M.E. L.O and F.O purifier. it will be helpful sir. salamat po

@@USAPANGNBA Noted JM. Will update pag meron na. Salamat!

Thank you! Have a nice day!

Oo ba. May request ka ba na tutorial, shout out kita dun hehe. Anything na pwede ko ma gawan dto onboard :)