chaser27

Пікірлер

@BMWMZ3X5 2 күн бұрын

Thank you! I was getting ready to throw mine in the trash.

@Grizzb28 14 күн бұрын

Awesome vid thanks 👍🏻

@chaser27 14 күн бұрын

@@Grizzb28 glad my spur of the moment video has helped so many people!

@seibertmurphy8849 Ай бұрын

Thank you! This is a useful video that can be used right away .

@jagdpanzer911 Ай бұрын

Thanks for sharing that tip, mate! Very helpful!

@warrenperucich4116 2 ай бұрын

Thanks, very useful video. My planer somehow lost its calibration when I replaced the blades. I thought I had purchased the wrong blades when I gave it a test run as It began to rip the timber even on the zero setting.

@tensazero 3 ай бұрын

Now I understand why it shaves at 0. Thank you greatly for the info. Will try this.

@matiasliddle5833 5 ай бұрын

Thanks so much! This was driving me nuts and your excellent video enabled me to get it sorted and restore my sanity!

@bigcat6329 5 ай бұрын

Used a pocket knife.. no damage. Just run blade along edge pry up.

@erikstreed2302 5 ай бұрын

Helped me on my Makita KP0800. Thanks

@dmgoslyn 6 ай бұрын

Terrible planer. Regret buying mine thing jams up with shavings every run down a door.

@manuchoar 6 ай бұрын

Obrigado pelo vídeo. Resolveu meu problema. Saudacões do Brasil.

@JamesBecker 7 ай бұрын

Thank you very much!!! I got this calibrated after watching your video. Great instructions. I wish I had found your video a long time ago.

@hotspur4237 7 ай бұрын

Thanks. I was having problems with my cuts and it kept breaking blades. This video was a godsend.

@keithburton99 8 ай бұрын

Thank you

@sethfritch4644 8 ай бұрын

Wow, thank you. I bought one of these a couple of years ago and I haven’t used it much because of this problem. I assumed it was designed that way and was just for crude carpentry. I had searched and about it and couldn’t find anything, thanks for making the video! Kind of BS that DeWalt didn’t have this in the instructions.

@paulbuckley9722 9 ай бұрын

Huge thanks for this! Mine was bad from new, just assumed it was bad design abstract finding nothing online and nothing in the documentation. Like other commenter, is much easier to get the top off by tapping with a screwdriver at an angle. 👍

@alextheman422 10 ай бұрын

Legendddddddddd🎉🎉🎉

@funkypotamus 10 ай бұрын

Top notch!

@shooter99999 10 ай бұрын

you can buy NEW knob from Ereplacment parts for $2.99, Just FYI and this help me zero in my planer so thank you

@BryantRanch 11 ай бұрын

Thank you for posting this video!!!

@enzoodorico7235 Жыл бұрын

Thanks for the video. Mine was also terribly calibrated. A tip to remove adjustment cap. Use a vice with wood to secure, then use channel locks and the screw driver. Much easier to get off, and won't damage it as much if you are careful.

@WaleshiddenhistoryMD Жыл бұрын

Good way to screw up your warranty

@Nats0x Жыл бұрын

g!b!

@LickorishAllsorts Жыл бұрын

Using a screwdriver to wedge the top off can leave quite a mess. Use the screwdriver at an angle and gently tap it with a hammer, the top will pop up without too much cosmetic damage.

@paulmorgan1636 Жыл бұрын

Just done mine thank you

@88MrRich Жыл бұрын

Thanks so much for making this video. Mine was perfect out of the box but that only lasted a month or so. Can’t believe DeWalt would make it possible to adjust it but not tell anyone how to do it, well done.

@_P0tat07_ Жыл бұрын

I just checked mine, the infeed and outfeed plates are pretty much spot on. But it still takes a massive cut even at the 0 setting. I put a ruler over the cutter head and rotated it and it’s dragging the ruler a full 1/2”

@anthonygreen9609 Жыл бұрын

Just re-calibrated mine using your method. It worked a treat. Thank you so much.

@chaser27 Жыл бұрын

Glad it worked out for you. I was super surprised nobody else had already covered this

@rytyky03 Жыл бұрын

Thanks for the tip. Works great

@thehandseesall Жыл бұрын

Thanks for this video, I needed it

@TheNish25 Жыл бұрын

Thank you!!

@SMorgan772 Жыл бұрын

Thank you! Solved the problem I was having no matter how much I played with the jig and blade carrier I couldn't get a 'zero' cut. All sorted now. If you do this adjustment take your time splitting the cap on the knob to avoid too much damage. I managed it with only a few tiny marks on the soft plastic. I wish DeWalt would design this with easier access?

@woodbutcher Жыл бұрын

Dude you are an absolute legend for making this video! Thank you!!

@chaser27 Жыл бұрын

Glad everyone is enjoying this one. I was surprised it wasn't covered anywhere else.

@sdw1986 Жыл бұрын

Same issue here. Thanks for video

@chaser27 Жыл бұрын

Glad you found the video and it helped!

@lesliebryce2244 Жыл бұрын

Sent my first one back after it hauled it's blades out, and would have gone for just a refund if I had not had the battery already for their drill. They must have sent out thousands of them all wrong. So glad you spotted that spot to get your screwdriver started. Big thank you from Scotland.

@VFRrider Жыл бұрын

You're dead right. Not good production value, but an absolutely awesome video!. Very many thanks for turning my planer from a good tool to a great one. 5 star mate.👍

@chaser27 Жыл бұрын

Glad it helped you out!

@Glorious_Kim_Jong_Un Жыл бұрын

Some people just want to throw a video up to help others. Not everyone uploads to become some big famous KZbinr. If he rarely uploads, this is more than good enough. Nitpicking when you have nothing better to do 🤣🤣

@frankvanrijn Жыл бұрын

Thanks for the info. My planer has the same issue, so I will try to adjust it using your method. Curiosity is awesome 😊

@chaser27 Жыл бұрын

You are so welcome!

@frankiebhoy7 Жыл бұрын

thanks for great video. managed to adjust mine to zero. It does chew up the knob a little bit when trying to get the top off, could do with easier access design from Dewalt. apart from that, great piece of kit 👍

@chaser27 Жыл бұрын

Glad I could help!

@JoeSmith-jz9hq 2 жыл бұрын

Thank you. I've been trying to adjust mine and couldn't figure it out.

@tomhuggard1510 2 жыл бұрын

Thank you brother! I just got one brand new for $110 but it cutting at zero made it useless to me. I’m glad I found your video, you just gained a new subscriber 💪👍🙏

@_gnarly 2 жыл бұрын

You’re a lifesaver man. Mine was awful from the factory too.

@Finxh 2 жыл бұрын

same here, taking off maybe 2mm while on 0. I tried to lower the blades in the drum with the hex tool Dewalt gives you but couldnt get the blades to sit any deeper. This video has definitely helped me

@chaser27 Жыл бұрын

Glad to hear you got it straightened out!

@andybason 2 жыл бұрын

Thanks for that, mine was taking 1mm off on zero setting, all sorted now👍, its pretty bad that they aren't set up correctly from the factory tho

@TheBonbenk 2 жыл бұрын

Thanks for the video man, I nearly sand down the base to make it flat. haha

@NineofSix 2 жыл бұрын

Thanks needed this to confirm my idea 💡, 👍👍👍😁

@rickyallen3074 2 жыл бұрын

That's not the way to adjust the blades to 0.. if undo the 3 screws that hold the blades, take them right out inside there is the blade holder where u adjust them there

@chaser27 2 жыл бұрын

I had already used the jig provided and verified they blades were installed according to specifications. It was nowhere near where it needed to be.

@richardhorsham7395 2 жыл бұрын

I have had the same issue I just purchased one used the little jig and is awful

@chaser27 2 жыл бұрын

@@richardhorsham7395 in the jigs defense. It is only really supposed to be used to align/level the back plate. The front plate is independent, which is why we need to do this as well sometimes

@leonbartley2937 2 жыл бұрын

How did you figure out how to do that? Nothing in owners manual about it. I did adjust mine as per your video and it got to where it still took of a little but good enough to live with. Seems like 0 should take off Nothing Thanks for figuring that out

@chaser27 2 жыл бұрын

I'm guess I'm just stupid enough to potentially break a brand new tool in order to make it better. I had an idea of how it would work had I designed it, saw the little pry tab. It made sense so I went for it. Glad it helped somebody out! I posted the video because I couldn't find any documentation of it either.

@alexwilliams2724 2 жыл бұрын

you should make more videos

@26dolla 4 жыл бұрын

Hey man thanks for the video. I see that this is a old video. How is the machine holding up?

@chaser27 4 жыл бұрын

It actually quit working 2 weeks ago. Just not heating up. I thought it was the thermostat so I ordered a new one for like $2 but it's still not heating up. Guessing it's the element now. Just not sure how to diagnose it better

@chaser27 4 жыл бұрын

Another update, I reached out to Mytee, they worked with me to get a replacement out at a heavily discounted price. The new version is even better then the first. More powerful, more stable, the gun is better quality and the hose is longer. Only complaint I have is some of my attachments don't work with the new gun.

@a350zing 4 жыл бұрын

Hows the new one working lol

@chaser27 Жыл бұрын

@nunyabusiness3786 Sorry never saw this notification come through for some reason. The replacement is still working great. I had a wire come loose one time and had to squeeze the crimp a little and put it back on, but other than that, it's been fantastic

@82923 5 күн бұрын

Thanks for your video, Is it still running?

@euricogomes9904 5 жыл бұрын

Really nice machine...unfortunely too expensive😔

@jennadollface 6 жыл бұрын

looks great i am thinking of getting it for doing my car myself , is it worth the price and how relIable is it thanks

@chaser27 6 жыл бұрын

If you are only doing one car and/or it doesn't have a lot of tight places I'd honestly just stick with standard buffer with ~5in pads. You'll be able to get close enough to the edges to not notice a real difference and it will make it go faster. If you want to go the extra mile, it's great for intricate work. I haven't had any issues with it reliability wise but I only detail on the side. I'm not using it day in and day out. Hope that helps!

Ең жақсы KZbin

Пікірлер