T f e t o f l a e t e s y e

I just found your video today. Very detailed. Thank you. I have purchased the same capacity controller It came without any cable and I am blind now. Please help me to get up and walk. I want to use this for my 4X 3.2 v lifepo4 batteries. How do I get a cable and how do I connect my lifepo4 batteries and capacity controller Thanks a lot for your time for coming to help me 😊

Going to Go Electric on My Cub.

Balsa motor mounts! What did you think was going to happen?

Helo good video ... i try to find GPMA3259 cowling 👍👍👍👍👍

I’ve waited 12 years and I’m still waiting for this flight 😊

I lost my cd software can do nothing

Is there a website for parts?

Poor Yorkie was frustrated! He couldn't get close enough to bite without getting pawed and clawed! Those little s•its are too stupid to know when to quit! No wonder you hear about them getting mauled to death by bigger dogs, both domestic and wild!

Good job man! I'm thinking about flying mine in a small area like that too but I've got a glow engine in it and I don't think it will land quite as good as yours with the electric motor! You did well with that hopefully I can get mine in that slow so I'll definitely be adding flaperons to it!

What size engine was in the airplane?

You didn't film the Bobbin for Pig Feet.

or......................... try throttle hold?

Rooster number one

How do u keep the fox's out if they can fit under the fence

Here take it don't crash it man.

can you use a generator that has 3 prongs but an adapter that converts it to 4 prong? My generator is only 120V but all the circuits I need is 120V. I have a firman inverter generator WH03242

With a DLE 20 you should be able to hover that craft. I flew a 1/5 scale hanger 9 w/ a sick .36 glow. It was like flying the full sized cub w/a very tired C65 and 2 persons. Still fun but……

Sny chance u could post a long term review

What motor and battery size is that? I just got one myself!

People definitely weren’t smarter back then

Very Very Good!!!!!!

Nice airplane. The flying not too good.

Did he really just cut a factory face side for a more even cut🤣

Get rid of the plants they will dig in the dirt.

what's the flying weight ( with 6S ) of that Escapade ....thanks ?

Pleaset include something helpful for first-timers … like showing the steps (buttons to push and/or levers to set) to actually start the impeller rotating.

I really wish Lincoln would list the inches per minute on the wire feed, really helped me to dial stuff in when going off of processes I read or learned about. Knowing the IPM really helps. Checked my Linc Power MIG 180 Dual; #3 = 180 ipm, #4 = 225, 5 = 300, 6 = 350 and 7 = 390 ipm. I wrote it right on my machine. Should be the same for the 180C or 180HD. (Start a stopwatch and the gun, release the trigger at 6 sec., multiply length by 10)

Never run the generator in the garage. Nat advised for safety. Carbon monoxide needs to be kept out side. Not to be near any door into the house. Especially with young children in the house.

19 inch for fluke in ny l.i

How many volts and amp.did u use for your power supply sir?

you have to clean you plane so it won't look like that

I want to build a rc truck

Which batteries did you use? I'm confused on how to connect 2 22v batteries. Any help will be greatly appreciated.

Is it legal that I could install this myself in Texas without a license?

Is it late to comment after 11 years when it’s posted?

Rooster, hen, hen, rooster, rooster, rooster!!

Get 5 cans of raid and spray those pests. also u should seal off any cracks in your door, wall, or floor. Also you should clean any spill or anything

My father have a chicken farm in our backyard, this make me wanna raise some rabbits to

one of those days

Yeah it's a rooster and will soon demonstrate some attributes of being one as it matures.

How to videos work best if you show people during the process, not after you are done.

If you look at you Loads you need to Balance them......to do that move a few C/B to the spot next to it. this will put the load on the other leg of your generator

Everything you do in the video is off camera or your head is in the way. Thanks anyway

ah this is making me want to get mine back out of hibernation lol

very nice intro wow yummy berries they have more berries in your farm love it.

"It's a little weird" just a bunch of dead bodies😂😂😂😂😂

its a rooster

Such a cute video!!

Glad that your one that like's to DIY, a few things I saw that you may want to consider, when routing the wires in the house panel make sure that they are not run or routed over the Hot bus the wires should be tucked over on the sides away from the Hot bus, another thing I saw is that your 10 gage wire from the generator receptical to the reliance control panel should be protected from physical harm being it was installed in a finished room that may be a code violation not being protected and just run like it was, personaly I would route THHN #10 in flex conduit from the receptical to the control panel so the wiring is protected. Other then that looks good. Curious to know about the generator exhaust system you were talking about making with a pipe and mufler worked out and if you did make it work?