I have a question I recently bought a used home eu2000i and I cleaned out the fuel tank and the carburetor and the internals…. The machine runs very good my only issue is that well it starts wanting to cut out around 1600 watts and then it drops and tries to pick up watts and drops again it never shows overload….. the green light does seem to momentarily go out….. lets say I kept it at 1300 watts I would have no issue take up a notch and it starts to stumble….
@dieseldawg71322 ай бұрын
Also my circuit breaker/ reset switch never pops out would it only pop out on a short circuit or would it also blow on an overload ?
@MartinMetregerTipsandTricks8 күн бұрын
Sounds like it could be several things related to a heavy load. Possible that the carb is not getting enough fuel delivered to it. Check flow from the hose going into the carb. It might also be a ignition coil breaking down under load. Hard to diagnose this issue. I would try everything else and then replace the coil. Good luck,
@dieseldawg71326 күн бұрын
@@MartinMetregerTipsandTricks hey thanks for your reply after messing around with the generator I realized two things one the spark plug was part of the issue and then also I had to clean the heck out the carb replace all seals after and it worked like a champ
@garymcgarity98392 ай бұрын
Thank you for the video. I had a transmission replaced in my 2500 a few months ago and now my flex plate is broken. Was seeing if I wanted to do it to save 700 dollars in labor.
@MartinMetregerTipsandTricks8 күн бұрын
Glad it helped
@jamesbeemer78552 ай бұрын
If you had the manual , you would know that , that machine has blue tooth . It will tell you something’s . But if you have to further to diagnose the problem , then this series of vids just might be what you need . This generator costs $1166 . Oo from a dealer , and Honda generators are damned neer bullet proof . Don’t throw it away if you don’t have to . The Japanese did us a huge favor as their technology to build things has greatly improved over the past 4 decades . My hats off to them .
@TheMetroCopMenace2 ай бұрын
I just got this for my car I’m almost 16, jeez this is so old 😭
@NJMS170003 ай бұрын
Hello, mu honda eu1000i 220v 50hz has a delay to start ac output. When this problem started, when i started the denerator i had to put eco throttle button on rabit to start to generate ac power inmediately. And now after i start, i have to wait around 10 - 30 minutes to start to generate ac.
@edryalvarez3 ай бұрын
Saludos como podria conseguir el avr de ese geneeador eu2000i
@user-im3fb4jf2q4 ай бұрын
very good, thanks
@doglegjake67885 ай бұрын
Excellent video
@genevelis60756 ай бұрын
I wonder if you could help me find answers to the following: Thinking to lower the pressure tank and connect to the pump about 10' - 15' under the ground to eliminate the heating well house in the winter season. My pipe runs about 6' under the ground. 1) is it a good idea? 2) how to do it? 3) Should I install another pressure tank under the house in the crawl space? The well is about 30 yards away from the house.
@MartinMetregerTipsandTricks5 ай бұрын
I don't have a good answer for you. The depth of the frostline can very based on location but a bad winter can exceed that. If your crawl space is heated, that would be a pain to get to but safer than under ground tank. But the pipe from the well would have to be buried 6' the whole way to the house. Check with a local well installer.
@genevelis60755 ай бұрын
@@MartinMetregerTipsandTricks Thanks. The pipeline already baried 6' under the house before it enters the crawl space from outside.. Crawl space is not heated.
@prepperboss6 ай бұрын
I have an older Predator 2500 inverter that runs beautifully but doesn't power the 110v outlet. I replaced the outlet with a household outlet and it worked on a small appliance. i started it later and it didn't work again. Any suggestions?
@MartinMetregerTipsandTricks6 ай бұрын
Sounds like you might have a broken wire leading to the outlet. Try pulling on the wire in different spots to see if it wiggles or comes apart. Good luck
@prepperboss6 ай бұрын
@@MartinMetregerTipsandTricks thanks I'll give it a try.
@nicuboboc95257 ай бұрын
Cum găsesc aplicatiea? La mine nu merge am trbuie o aplicație
@MartinMetregerTipsandTricks7 ай бұрын
There is NO APP. Sorry. This unit is older but it will work with Bluetooth
@anokaramsey09 ай бұрын
very nice !!!! i am working in the same system for my 25" Rv!!!! i take few good ideas from your project!! Thank you
@MartinMetregerTipsandTricks8 ай бұрын
Awesome! Thank you!
@Planespotterdude9 ай бұрын
Same issue on my brand spanking new eu2200i. I got it yesterday. Kept flooding i paid out of pocket for the fix. Now i get home, have green light, no power. Tested as a ground reverse. I dont know how to fix it so im returning it
@raynic117311 ай бұрын
Thanks, I have a dead one also, hoping to figure it out. Thanks for the info...
@ronalddesharnais602211 ай бұрын
What is the site you obtained the manual from?
@MartinMetregerTipsandTricks10 ай бұрын
It's been so long I can't find it. Sorry
@loosemink11 ай бұрын
Mine is having the same problem, no power coming out. I'm gonna go through what you have shown. Thank you for doing this video ❤️
@MartinMetregerTipsandTricks10 ай бұрын
Glad I could help
@THEGUNSGOBOOM11 ай бұрын
Thanks for the video
@MartinMetregerTipsandTricks8 ай бұрын
You bet
@joshuahall980911 ай бұрын
I bought a new fuse and it says line & Load but old one doesnt say anything on it please help.
@MartinMetregerTipsandTricks7 ай бұрын
That is strange that the fuse is directional. Most are not. Line to inverter and load to outlet. Hope that helps.
@user-qf6jt4tq9i Жыл бұрын
Do you recall a part number for that wire? After an hour of troubleshooting your video took me right to the problem.
@MartinMetregerTipsandTricks10 ай бұрын
I found one at a mower shop that took it off parts inverter. You have to check around or fix the one you have.
@user-qf6jt4tq9i Жыл бұрын
Do you recall a part number for that wire? After an hour of troubleshooting your video took me right to the problem.
@MartinMetregerTipsandTricks9 ай бұрын
No part number available. I had to find one used at a repair shop. They just gave it to me.
@user-qf6jt4tq9i Жыл бұрын
Do you recall a part number for that wire? After an hour of troubleshooting your video took me right to the problem.
@MartinMetregerTipsandTricks7 ай бұрын
I could not find a part number. I believe it is discontinued. Repair the wire or maybe you can find a dealer with old generator parts. Good luck.
@andrewshaw7929 Жыл бұрын
Awesome video. Thank you very much Martin. We are anchored out in Georgian Bay and woke up to make my coffe and charge the house batteries. My Honda 2000i had the dreaded no AC,ughhh. I went through your testing procedure and never guess what I found. Yep, my white AC output wire has broken right at the connector. Exact same issue. Jammed the wire back in the connector and put a little dab of JB weld to hold it in place. Just a quick fix to get power, will replace the connector when back home. Thanks again Martin, you're a life safer.
@MartinMetregerTipsandTricks Жыл бұрын
Great to hear. Thank you,
@jedzuniga8739 Жыл бұрын
Great video ty
@MartinMetregerTipsandTricks Жыл бұрын
Glad you enjoyed it
@manuelmach86 Жыл бұрын
I bought the 2200 but i should’ve got the companion because of the 30amp plug for my rv. Is there a kit to change out the plate containing both plugs? A plug and play kit that contains a 30 amp plug? Essentially turning my 2200 into a companion?
@MartinMetregerTipsandTricks Жыл бұрын
I don't believe so. Sorry,
@donniereeves5473 Жыл бұрын
Lol DYI
@Antiorganizer Жыл бұрын
I'll pay someone to do it, but I appreciate seeing this walk-though. You sure have a lot of patience... I wish you were my neighbor, lol.
@MartinMetregerTipsandTricks Жыл бұрын
Thank You... This is a big job and I tell people to have a professional do it if they have any concern. One mistake could cost way more to having a pro do it. But at least you know what is involved.
@user-rj8iy3er6w Жыл бұрын
Отличный обзор!!!
@vladutnita5627 Жыл бұрын
Thank you
@mendonesiac Жыл бұрын
Thanks so much for the great tutorial on how to test for voltage... and your wife is right that you're a nut -- you should never run a generator indoor!!!!
@MartinMetregerTipsandTricks Жыл бұрын
Glad to help
@mastahaze420 Жыл бұрын
Did you use galvanized or pvc for the piping?
@MartinMetregerTipsandTricks Жыл бұрын
PVC Schedule 80
@bcy42 Жыл бұрын
Hey Martin, I just changed my spark plug, carbeurater (old one had a broken choke lever), and air filters. When i put it back together, it will only idle at a very low RPM. No power from AC outlets. Any advice what I should check for? From looking, this is not a very common problem.
@MartinMetregerTipsandTricks Жыл бұрын
Sounds like the linkage to the idle control solenoid is not hooked up right. or the control solenoid is not getting signal to raise the idle. Try disconnecting the linkage to the throttle and manually increase that throttle and see if you get power. If you get power, focus on the idle control solenoid. They do go bad.
@hailskins92 Жыл бұрын
its holy not holly
@hailskins92 Жыл бұрын
awesome made part of my playlist of favorite videos
@MartinMetregerTipsandTricks Жыл бұрын
Wow, thanks!
@hailskins92 Жыл бұрын
a star is born
@hailskins92 Жыл бұрын
shave your knuckles
@hailskins92 Жыл бұрын
are you sure this is faster and easier then taping up the trim piece?
@MartinMetregerTipsandTricks Жыл бұрын
Maybe not faster but less damage to the trim that i am reusing.
@ke6bnl Жыл бұрын
Like your pipe holder idea
@MartinMetregerTipsandTricks Жыл бұрын
Glad you like it
@Eeprom986 Жыл бұрын
Nice work I have the same Honda, have a problem with 12 volts DC port I found 24 Volts Any suggestions to resolve this problem?
@MartinMetregerTipsandTricks Жыл бұрын
That voltage test should be checked while hooked up to a 12 volt battery. You should see around 14.5 volts + or -
@johnathankeough30275 ай бұрын
Bad rectifier module
@davidfisher3273 Жыл бұрын
Very informative video. Thank you
@MartinMetregerTipsandTricks Жыл бұрын
So nice of you
@oliviasorensen9476 Жыл бұрын
Excellent tutorial, thank you, very informative
@MartinMetregerTipsandTricks Жыл бұрын
Glad it was helpful!
@jacobalderton9262 Жыл бұрын
Can you link where you found the wiring harness
@MartinMetregerTipsandTricks Жыл бұрын
I went to a small equipment repair shop and the sold me a used harness. It was hard to find. I actually fixed my harness before I finally got a good one.
@juancosta2647 Жыл бұрын
hola tengo un generador igual al de tu video, es 120v. yo vivo en la argentina y la corriente es 220v. tengo alguna forma de convertirlo para 220v
@MartinMetregerTipsandTricks Жыл бұрын
That is a good question. I don't know enough about your electrical voltage to provide safe input. I'm sorry.
@juancosta2647 Жыл бұрын
@@MartinMetregerTipsandTricks hola no entiendo tu idioma, me podes responder en español
@MartinMetregerTipsandTricks Жыл бұрын
@@juancosta2647 Esa es una buena pregunta. No sé lo suficiente sobre su voltaje eléctrico para proporcionar una entrada segura. Lo siento.
@fool4wheelin Жыл бұрын
Nice video, I had the same problem with mine, broken connector terminal on the white wire. Must be a common issue with these units. How did you fix yours, did you solder the terminal back together? I’ve been trying to find a replacement terminal with no luck.
@MartinMetregerTipsandTricks Жыл бұрын
I did solder it back together because I couldn't find a replacement myself.
@nishanthademel9114 Жыл бұрын
Hi
@randallmitchell22142 жыл бұрын
Same exact thing with mine tha .thank you, problem solved
@MartinMetregerTipsandTricks2 жыл бұрын
Glad to hear. Thanks
@brianpeever23002 жыл бұрын
Martin what is the name of the winch tower you use for this job?
@MartinMetregerTipsandTricks2 жыл бұрын
Well Brian, I used a LA12-18 Mini Line Array Tower 12in. Euro Box Truss from the sound company I work for. They sold the tower and winch. I help a friend with his well and used a hoist like this amzn.to/3pdBhKs with some Unistrut and scaffolding. Check your well depth. Should be posted by the surge/bladder tank. I don't recommend DIY for wells deeper than 300' . My friend well was 400' deep and it sucked. Really scary weight and took forever with all the pipes.
@johnwebb78822 жыл бұрын
I was having a problem with my Honda generator. I hade the same wire come loose as you. Did you get a new wire plug or solder it or what. How did you fix yours. Thank you
@MartinMetregerTipsandTricks2 жыл бұрын
I replaced the end with a connector that I scavenged from misc parts bin. it wasn't the perfect part but it still works to this day. I tried to order the harness but not available. You can maybe check your local small engine repair shop to see if they have a used parts inverter around. Good luck,
This is one of the very few diamonds in the rough sort of speak videos. This was very informative, instructive video that pointed out many small issues and mitigation methods to ensure plenty of time before next replacement. I worked on the above ground electrical on an agriculture irrigation well. relocating the control box to a more suitable location. The well was established about 5 years ago. Last week the ‘start’ leg circuit breaker popped. Your video helped me understand all the ins and outs of well pump replacement.👍🏼👍🏼 Awesome Instructions and very dedicated to sharing knowledge! Thank You!
@MartinMetregerTipsandTricks2 жыл бұрын
That's an awesome comment. Thank you for the kind words.