zuviel Plastik

Lose the baggy sleeves... 😮 I have the Triton "bench 12" planer and I love it !! I also bought the Triton TRA001monster of a router for my homemade router-table... the built-in router lift was the deciding factor in choosing Triton... 😎👍☘️🍺

Great resource. Looking to get a MK3 and needed some instructions!

Hi Matt, I have a TRA001 mounted permanently under a router table. Problem I have is when I release the Locking Lever to make a fine adjustment, the bit drops down a bit, making it very difficult to make a quick fine adjustment. Is there a solution to this?

Would be great if the TRA002 is available. No where to buy

I am a carpenter from Kenya planning to come to s Africa any opportunity

That piece of plastic covering the switch is stuck... Any advice? Can't turn it on, probably need to break it off. No time for warranty repairs

re seeing it... love it <3

I didn't know mustard could be used to glue thin plywood, you learn something new every day. And at 6m12s, you can see a monochrome watermelon ceiling!

Would you use self tapping screws for the battens ?

looks decent

This piece of crap has broken twice in the 4 years I have owned it and the replacement part has been unavailable for 6 months. I’ve gone to Bosch .

Nice. I can't believe you did that end cut on the table saw without fence support. Amazed you pulled that off. Good work!

How do you stop the bouncing I want to buy one but in this video I see that it's bouncing around on the orbit mode

Where do I buy height adjuster gears

I have all the tools used in this video and can confirm that they are all good quality and value for money but if you have the thickness planer on a mobile cart like I do then you have to check the infeed and out feed table constantly to avoid making the inevitable snipe worse.

Mine is at least 22years old! The newer models don't come close to it!

Promo>SM 😭

Why did I get a 1/2" and an 8mm with my router? When the most common is 1/2" and 1/4"?

Hi can you get the latest fence to update existing contractors saw?

Fantastic!. Looks great. Lots of ideas for me next van conversion

Some fantastic tips and detail!. Thank you guys

Very nice work! 🎉

Stuuf the music.

Absolutely stunning. My Wife had a large glass topped Coffee table many years ago, and the glass got broken. I made a plywood insert to replace the glass with a design painted on it. Despite very careful sanding, I couldn't get the Polyurethane smooth. No workshop, spray booth or air supply, so brush painted it with Polyurethane. There was a lot of dust about. After about 6/7 brush coats, I was beginning to think I would never get the shine or smoothness I wanted. Then I had a brainwave. Lightly sanded it with a fine grit and then 2 or 3 goes at it with an angle polisher and T-Cut. Came up fabulous. 👍👍

Beautiful!

One of my favourite parts of woodworking thanks for posting

Is there a special kind of glue that you're using? I'm sure it's not elmers lol but will any "wood glue" work or will it need to be a certain type?

I used a glue gun in a large camper van, one of my first tries luckily I did not use it on anything structural just trims etc. One very hot day at the beach we returned to the camper to find things falling off the walls. I have never since taken note of advertisements showing a glue gun mending chairs etc. That was in 1967 I believe the glues and guns are slightly better now.

I was pleased to see a black tank to cut down on algae and mould. I always use see-through then sand all over with fine sandpaper apart from a small strip top to bottom that I put masking tape over then I spray paint it black leaving the two strips to see the level. Water is always fresh. If you expose the black tank to the sun it will heat the water fairly quick for washing up the dishes or washing down. Nice videos.

So satisfying 🔊🎧🎚️

🤘🏽

My allen screws are tighter than a nuns snatch... i cant get them off the blade

Those tools for the price they have are very interesting.

Sad to see great oak trees been cut down for this ship as much as it looks a great ship just a pity for the oak trees that take so long to grow.

最近メインで使って、重宝しているよ。ところで、回転数可変って、どんな時に使うのかな。普通にいつも、ダイヤル6のまま使っているんだ。

Hi Matt, I liked your video very much. Now I get the feeling you are in the States, and I am in the UK, where I must say, the aftersales is not that good. So I wonder if you can help me ? I have a TRA001, and for ten years it has never let me down a truly great router. Until now. The automatic spindle lock has stopped activating, and as it's table mounted, it's a damn pain in the.... Now my question is: Have you ever come across this problem, and/or would you know how to fix it ? I get the feeling that the only way to get to it is by unscrewing the small screw beside it's housing, but I am reluctant to do this as the 'manual' such as it is, doesn't even mention it. I apologise for rambling on, but any help you could offer would be most appreciated. BTW, your work looks amazing. Kind Regards, Bernie SW Wales UK 👍👍

I use my big PC routers for CNC. I have a bunch of precision Think and Tinker collets which are better than anything offered on a handheld router. I am assuming that Triton didn't copy the collet system from PC?

Any collets available other than the 1/4" and 1/2"?

Nice. I need one.

Класс

Need some contact details guys. Need a charger for a new Triton drill I was given ?

What brand is the stand you use?

Brilliant video, I was about to buy one. But the 3 years guarantee is domestic use only! And the return postage for warranty is down to me. A shame.

Very bad designed

Still have my Triton 2000 work bench!

持っているよ。日本の製品に比べると、各部の仕上げが今一つな部分も多いけれど、とても精度が高くて便利に使っている。しかし、見れば見るほど激安ブランドのWENのPlunge Track Sawと、同じパーツをあちこちに使っているね？全く同じではないところが興味深い。工場が同じなのか、パーツ供給元が一緒の部分が多いのかな。

Awesome series Ben, the guitar came out beautiful, nice job!

22:36 ... "its still a damn sitght tighter than most" ...thats what she said😅

Do i detect a South African accent...? 🇿🇦