@@TekashiFPV so far I have been very satisfied. I've got two 20x20 and a 30x30 . No complaints

@@CrashTestFPV-jo1yn I love it

I've always been in smaller controllers like x lite pro for years.

@@cajah1000 yeah I have a Pocket and the dji rc2. But the T15 just feels so much better. And you get way more resolution. But I still like the Pocket.

U01 camera 256x192

@cajah1000 thanks!

The Goku 20x20 ESC is a good one but I but mine by the stack. It is AM32 firmware.

I use the Goku for the vtx switch it your doing a GPS it's good for waiting on satellites or you'll have to hit start it with 5v, pit switch etc or get a little air duster for cooling.

​@cajah1000 i don't think it will fit the Flywoo Explorer frame, I only have 30mm in between the standoffs

@jamesmason7124 I'll measure mine

@jamesmason7124 nope 33x30.6mm I'm not for sure what your going to for on there not many. You may have to go with something in a 16 TBS lucid maybe but it'll be too long

@@FAWK_YT_Democrats_Liberals it'll be soon but I got another video coming with hdzero recording and it's allot better. Still want a bigger view. That video will drop soon and it's a big difference same camera.

@@FAWK_YT_Democrats_Liberals y'all wait for the next video. The thermal is a lot better in the HDzero goggles

@@FAWK_YT_Democrats_Liberals never spent a dime on DJI

Just subscribe lol I'm going to circle around but sure it'll pull more power when I get the vtx table figured out. It'll get out there and I like it but they should have a vtx table available

@@PiDsPagePrototypes not neither one of those issues. I got the rapid fire feeding my hdzero goggles with no flicker at all.

@@cajah1000 Odd,... That roll in the image is very much like loss-of-signal resync from a bad connection. Is there a was to get video direct from the camera, check it seperate to the rest of the system?

@@PiDsPagePrototypes it's the walksnail goggles X. It works fine on av cable to my hdzero goggles and on the analog screen. I had the same results when I used my rapid fire module and bypassed the expansion module.

@PiDsPagePrototypes I have an analog screen that will be here tomorrow that has an HDMI output that I'll try on the goggles X to see if it still happens.

@@cajah1000 Another thing it could be, and it does look like it's still there on the screen you show at the end, is a mismatch in the frame rates. Most LCD onwards TV screens have a frame buffer built in, so it'll hold the last frame till the next one comes along, hiding connection issues. (CRT's usually had a single line buffer, and rare ones had a frame buffer) If there's a mismatch in the frame rates, the flicker is from it waiting for the next frame of video to arrive.

@@sneakerhead3256 it has been working great as long as the wind isn't blowing and you calibrate the accelerometer correctly. I use levels in top of my motors to level mine because calibration.

@ did you use the browser to flash? I can’t seem to find the 4.6 update option. Only see 4.5.1

@sneakerhead3256 make sure you have it set to show beta releases. I think I used the app to pull the beta and flash but you have to use the browser to connect. The app will not connect to 4.6

​@@sneakerhead3256works in either one choose the development tab

@ finally got that aspect now I can’t get osd working on 4.6 did you have any issues?

@@HPFPVS I don't use a GPS it's fine as long as I plug in and go. I am going to try one soon. I've got a pro set up and multiple others.

@@HPFPVS this was just a test run to see if I would like the set up. I'm going to get a better thermal camera now with the different modes and larger field if view. Possible head tracking.

@@GR33ZY.A1 yes all you have to do is use user 1 on a switch. And set the range to be off when you plug in.

@@batjos74 me too and I don't have the greatest workstation 😂

You can purchase them at multiple places. Just race wire LEDs. I think these were called tinys from race day quads.

It is just led/race wire and yes the ESC supplying the motors effects the brightness so when you throttle they get brighter.

FPV UNGLUED it was still fun just wished I started with my main first.

Poker2145 Yes you will have to replace the bottom frame from time to time and the columns strip easy so if you can upgrade them as they strip would be better. I have started flying the Goby 210 frame now but still fly this one from time to time. motor still works.

Poker2145 the center bottom frame was about 9 dollars I think. I got it all ready to fly with remote and goggles so I was satisfied for starting with it

Super - Thanks for the information.

Ian Rice I still fly that one some I upgraded twice but when I flashed cleanflight 2.0 it was a lot better in flight but still one bad motor keeps on flying.

I'm glad you still fly it. how did you upgafe to 2.0? I had to find a way to get the old version so I can still adjust rates n stuff. I'm using 1.2.4 but I would like to use the new 2.0 version. I can fly dam good acro but I'm not good with allot of the programing. Would you be able to make a step by step video on how to upgrade to 2.0? I'm sure it would help allot of people. Thank you.

Ian Rice check out project blue falcon...have you flashed the board since you got it?

Ian Rice all I do is hook it up and flash. The V2 I don't even have to jump the boot pins.

cajah1000 No I have not flashed the board yet. All I did was change rates add an arm switch and add angle, horizon and acro mode. And change fpv cams and stuff like that. I'll look up that video now.

Mark Scheler ev800 it was a rtf kit good eco start lol

Mark Scheler At9 transmitter

thanks, I have looked at those on amazon. the drone I'm looking at is bnf. Already have tx/rec, so just interested in goggles

the other video is eachine dvr goggles

modernkilla82 yes bottom frame is week on the screws I ordered a new bottom frame, extra screws and columns.You can super glue small washers on one screw on all the arms then tighten it down that will strengthen that part that's what I ment by bandaids I had two washers on flying in this video to hold two arms on.

Flying in acro mode