Do the boards on the upper deck need to line up with and finish to the rafters below? Exact positioning is only approximate so can the boards butt between rafters?
@PeteAulton-z7b2 күн бұрын
Do the upper boards need to line up (finish) with the rafters below or can they join between rafters?
@blacksunset-x1g6 күн бұрын
it looks like nextdoors extension is onto your boundry / land by about a foot?
@yougetmeblood1419 күн бұрын
Great video very helpful 👍🏾
@SheilaMaoMao11 күн бұрын
What is the size of that long screw you use at the top of the plywood? What is the spacing between long screws around the perimeter and between inner? Thanks
@stormyjon449318 күн бұрын
How much did that cost?
@user-ju1du2sm6bАй бұрын
Will i be able to lift my 8*3 by myself? Thx u method makes sense
@McdonaldRoofingАй бұрын
I have found using a 2 inch roller as you heat up the epdm helps drastically.
@baldyslapnut.Ай бұрын
The vapour barrier should be on the inside of the upstand, it's to keep internal moisture laden air out of the insulation.
@barrym9610Ай бұрын
Very helpful 👍
@WSpa-if3og2 ай бұрын
Screwing through the VCL.
@willahmad4372 ай бұрын
Hi there, thank you for the very informative video. I am about to place an order on the link below, but I need a bit more info (sorry for my poor knowledge, a beginner DIY...), Our shed's roof is Self Adhesive PU Flet Sheet. A few years, it's not bad but needs some attention, I want to polish it with this Arboflex Pu, followed by UV protection. My question is ) is it ok to use Fibreglass Matting on the PU Flet sheet? and b) Just to reconfirm, is Arboflex Pu, ok to use on the PU Flet Sheet? (I am sorry, as I am still learning so want to make sure before I place an order at the below link)
Please be straight to the point. Not everyone wants your humour dose
@barrym9610Ай бұрын
I actually really enjoyed the video - better than some drab, boring, monotone instructional were usually subjected to. And you're getting it free ya big grump! 😂 I'll say it again, well done lads - excellent video!👍
@jimmykahn54312 ай бұрын
Can you out a roof lantern onto an existing flat roof and the Remainder rubber roof.
@mrboyban2 ай бұрын
Resitricky I should say...
@tomday-gb9kv2 ай бұрын
Hi, good tutorial. Can you put extra insulation between the rafters/joists underneath the warm roof
@Alex-if3srАй бұрын
No then it becomes a cold roof and needs to be ventilated
@plummetplum3 ай бұрын
You missed a trick by not using thermally isolated fixings, I am sure you do on your subsequent projects since :-)
@123sumom3 ай бұрын
My flat roof felt is melting,. Its mineral its needs Granular stones.
@MichelleLane-vd7bs3 ай бұрын
Is it usual for them to leave the old felt on the roof then do this on top with felt again on top?
@user-lf7gn4ku9n3 ай бұрын
What is your option on what most roofing manufactures are saying the top osb3/ply should not be used and the roofing product fixed directly onto the insulation. Also the correct flat roof insulation is not foiled back if adhering or torching on the top cover. It must be fleece backed such as the kingspan Thermaroof TR26 or TR27. Full detailed descriptions of the technical reasons I can quote from them. But the short of it is that the top cannot absorb or disperse the heat and is subject to below-ambient low temperatures. So subjects the material to moisture vapour cycles which repeatedly condenses and evaporates on its surface, so in time the top deck will rot and compromise the performance of the system.
@JohnSmith-rp7bc3 ай бұрын
No, the first thing to do is treble check that there are no protruding nail heads, splinters or debris after you’ve first rounded off each sharp corner and edge
@ultimatehairsalon57933 ай бұрын
Very good job done, but where would the water drain of because the pipe is a little bit higher to the insulation. Thanks 🎉
@peakyblinder28473 ай бұрын
Soon as you screw down your boards you are screwing the tape you first put down. So will sweat
@condoritoalvarez61503 ай бұрын
How many squads does that job have, sir?
@user-qz8wp7hy8x4 ай бұрын
Why not just torch on two layers again. Far better job no need for pu mastic or any of that prep work. No need for reinforcement matting or any of that shite… torch on still the best flat roof…. Fact
@simonhedley37844 ай бұрын
Great advice- thank you!
@scottyjimbo98834 ай бұрын
Great video I've bought some 18mm osb3 bourds but the ones I've bought just say kronospan on one side there doesn't seem To be a rough side both sides are smooth Should I sand it or return it for a different type ? Thanks in advance
@stevo123494 ай бұрын
in other words dont fit it in the UK
@macitect4 ай бұрын
Good video - but you could have saved the client a bit of money.... osb acts as a vapour barrier, just needed to tape the joints. Also, was the waterproof membrane EPDM? It could have gone over the insulation without yet another layer of osb...
@johnsonkevin12 ай бұрын
OSB does not act as vapour barrier. EPDM can not be layed over foiled PIR
@macitectАй бұрын
@@johnsonkevin1 Yes it does. I learned this working on Passivhauses and have employed it many times since. If used on the warm side and the joints are taped. Not an airtight layer, but certainly as a vapour barrier. And EPDM can be laid over polyisocyanurate (PIR) insulation, perhaps not the foiled stuff - I don't know about that - but it can be either adhered or mechanically fixed.
@shervinmokthari12515 ай бұрын
Hi, I've recently had my 60m2 flat roof replaced with a rubber roof with one join. The thing is, it doesn't feel like it's stuck down properly. The waters pooling because there isn't enough pitch & the side with the gutters aren't stuck down properly so the water can't run into the gutters. There's also no vapour barrier which makes me think could be a reason why it didn't stick down properly. I was charged 13k just for the roof replaced not including scaffolding
@havitoldulatelyАй бұрын
Did you get other quotes? That's incredibly expensive. The good news is it shouldn't matter if it's pooling water won't affect this material. If it looks like it's not been stuck down properly I'd send them pictures and ask for some money back and threaten to take them to court if they refuse as you've not got what you paid for.
@douglasreid77275 ай бұрын
There should not be a timber cover placed over the insulation.
@TheSlimpickings5 ай бұрын
What sort of thickness of OSB board would you recommend for a garden studio re-roof. Can I use any OSB board to lay EPDM rubber on top of? Thanks :)
@jablot50546 күн бұрын
18mm
@rickieb73385 ай бұрын
What is the actually purpose of the membrane . If water ever built up wouldn't it just turn into a pool of water
@Shahakha5 ай бұрын
If you mean the vapour barrier it’s to stop water vapour entering from the room below and then condensing on the cold side of the insulation i.e the top of the insulation just below the waterproofing layer.
@nawal77215 ай бұрын
Hi need help. Is OSB wood or structural Plywood better suited for a summer house roof (7m x 4m)? I see everyone is using OSB, but my handy man recommends structural plywood but it is about £150 - £200 more. I'll also be covering the roof with EPDM rubber membrane (classic bond).
@nawal77215 ай бұрын
Hi need help. Is OSB wood or structural Plywood better suited for a summer house roof? I see everyone is using OSB, but my handy man recommends structural plywood but it is about £150 - £200 more. I'll also be covering the roof with EPDM rubber membrane.
@jablot50546 күн бұрын
18mm osb
@whatmouth5 ай бұрын
Gunning that chase like a 5 year old what a mess try laying it directly over osb with out old felt under it wont last 5 years you know it i know it .just not roofers end of ...chancers roller and a sweeping brush. talk the talk love to see them on some tricky detail be like a dirty protest they'd be covered in the shite
@mrboyban5 ай бұрын
Hi there, Would you mind me asking you,... I'm doing it on my own and the weather has been the main factor to watch out. I've laid the first sheathing which took me the whole day.... How long did it take you to lay the deck from start to finish? Many thanks!
@bradleyashford88036 ай бұрын
Doing my first one this weekend done plenty with someone else as labourer see how it goes now private job
@WhiteManInAVan6 ай бұрын
What I've always been confused by is how is the osb that the insulation is on not a cold spot issue?
@vertclimbergaz6 ай бұрын
Hi mate did you lay a rubber membrane on top? Thanks
@cragousg6 ай бұрын
Good to see tom on the tools😅
@howodd20167 ай бұрын
Great vid, curious, what’s the cost to have this done. Looking to replace ours with a solid roof
@mrboyban5 ай бұрын
I reckon it was about 3000K, using OSB3 which is way cheaper than plywood, cheaper insulation, then the most costly -> allutrix and resitrix .
@ck008uk7 ай бұрын
There is a expensive version of PIR for flat roofs. Does it make any difference? For example: 120mm Recitcel PowerDeck Flat Roof Insulation Board 1200mm x 600mm is double the price per square meter compared to 120mm Recticel Eurothane Insulation Board 2400mm x 1200mm
@user-sg4zm6oh7o7 ай бұрын
Can this be applied over grit coated torch down with patched areas of both asphalt and elastomeric?
@gilsonst7 ай бұрын
How much? South Yorkshire
@shaunyshaun868 ай бұрын
Personally alwitra is the only membrane suitable for large domestic and commercial flat roofs its durability and breathability is unmatched
@MrFlatroofer8 ай бұрын
A 3 layer polyester system is a minimum of 8mm
@RichardABW8 ай бұрын
It would be good to know what happened around the pipe. Is there a pipe embedded in the insulation?