Is this tool available now?

How do you change the seal on a sgs 2.5T trolley jack. Lifting range 75-515mm. Model number:TJ2.5LP?

misleading instructions

Mine will raise, but it won't raise while under pressure. Ill try this and see if itll work.

Didnt work on mine still hisses

Thank you for that bit of information ☺️

is 370mm height too high for a peugeot 308? will it tilt over?

Thank you

I did it too. This is what I used Woodglut designs for

Thank you. Worked like a charm

It's a wonderful website, just right to know what to do with the floor jack. Thank you.

Thank You!I thought I would have to throw mine away!

Where can I find this struts besides Amazon?

Hi there. What decides your P position? Did it need to be 160mm in relation to the strut length or did you just decide you wanted it to be 160mm?

Variable gas spring, added a relief valve on a compression gas spring, filled maximum gas, then release it when using, just reduce the force, so release the pressure need more careful.

Some narration would have been more useful than the music, which I had to mute because I hated it.

Thanks sir for a great video. Purchased a new jack yesterday and couldn't get it to lift, watched your video and it worked. Great job!!!

Thank you!

absolute waste of time not showing where the axle stands are placed, even if its car specific, the type of location will give clues to other cars, this is typically not the information one can find in the handbook

Thank you for the instruction. My jack was pumping up OK but when I release the pressure the whole thing collapses!

My old floor jack wouldn't lift high enough yesterday, today I will this, stay tuned .lol

Hi what does it mean to subscribe

WRONG. you need to pump with the valve open and then open the oil filler plug to let the air out.

Wow, what a pointless video

À

I bought a pair of struts that have failed after 6 months. SGS want me to send them back for inspection. Meanwhile I have a tailgate I cant lift, & out of pocket for the shipping. NOT IMPRESSED

Ah yes youtube saving people with no dads

Yeh right

On mine, the pin under where the handle goes up and down does not come back up. Any idea what is causing this ?

I own a similar jack except mine has additional mechanical parts that will limit the lifting mechanism from dropping so that if the piston fails, the load will still be held. After using this jack for 10 years, I found that the car was dropping 1-2 centimeters while supported by the jack. Today I purged and added new oil. I found it easier to place the jack vertically in a plastic milk crate so that the bleeding hole was pointing upward. After completely removing the bleeding hole screw, I could see the ball bearing check valve at the bottom of the bleeder hole. I added a bit of new oil in the hole and pumped very slowly until the new oil dropped under the steel ball. I repeated until all the internal air had been replaced by new oil. I used about 100 ml. of oil. Then I put the jack back on the floor horizontally and with the valve closed, I pumped up the jack to its full height. Then I released the mechanical locking mechanism and lowered the jack. Then I rechecked the oil level for a second time following the same routine. You should use oil designed specifically for hydraulic jacks. I hope this extra information helps.

By mandatory personal moral rules. I had to sign on and like and comment. To Thank you 🙏 . Using the pole to release air, did it for me.

Get a new screwdriver, you butchers

Very helpful, thanks!

kzbin.info/www/bejne/iWXXeZ-Adr-FeJo

Terrible sds drill. Motor burns out uncomfortable and hugely overpriced.

There's two of them, if this isnt wahmansplaining i dunno what is

Mine doesn't start that easy usually stalls after about 4 more pull starts it runs on half for leat 5 mins before you can take choke off

That SGS thing in the end scared the pile of crap out of me.

Do you ship to the US? Or know a US equivalent company?

The very start of your video sounds like Rough Boy by ZZ Top.

I recommend Woodprix to every beginner and not only.

Woodglut is a solid company with solid woodworking plans.

My problem is the Jack lifts to its height no problem but when I place it under the car it doesn’t want to lift. Can you help

kzbin.info/www/bejne/gnu5i5VrbtymeJo

That easy, yeh right !!+

thank you so much for saving me from another trip to autozone

Do you ship to the US?

As already commented in an earlier post, this video completely contradicts what is printed in the owners manual that accompanies the jack! The customer service isn’t too good in my experience either, so this anomaly explains it.

Thank you good sir, just got my first hydraulic jack last night. Never used one before (I’m 22), since I want to learn the basics of car maintenance, decided to get one. Now thanks to this video. I know how to operate it. From purging the air to lowering the jack.

Great tools ryobi