When you took the drill bits out the case what size are they? I dont have that tool to tell the size. For example were they 1/4 or 7/32 or 3/16

You think these would fit my 1996 Honda Civic?

Your diff seal was fine after this? Did any oil leak out while you were replacing the axle?

Good video, I have a 25 hp Kohler leaking oil. I was afraid I would have to pull the engine, this looks a lot easier.

What is the part# for this Bearing and seal been 12 weeks broke down dealing with Honda someone help

Nice R! I've never seen a standard R, but it was an R that I drove 70 years as a young kid. Good memories!

I hate the 8 speed tranny, that’s why I offer a custom 7 speed tune

On the main jet are the threads a insert? I tooo Mine apart, pulled main jet, cleaned everything and went to put it back together, and the threads are gone

wish you would have done the rope install. Which spool do you wind it on?

Ha ha ha "The top ring just has to get compressed together" easier said than done while keeping the ends off the rings on eighter side of the tiny pin in the ring grove. I would have liked to see how you did that.

I would like to have see how you kept the rings in the correct place at the pins and inserted the piston into the cylinder.

Thanks for a very informative video. Question, if I installed a new TPMS module, if I do a RF hub reset and putting in the vin would that program the new tpms module? Thanks

Thank you

I order HD variable rate springs from Simcoe Spring. Installing them next week. Thanks for the help. Other instructions have said to remove 4 sway bar bolts from axle. This looks easier.

I don't have one. Are there other ways?

Unless a person is prepping for some HEAVY tow weight, would there be any other reason to replace the coil springs, the ones on these Gen 4 Rams are pretty heavy duty to start with. Shocks and bumpers I can see, but unless coils are broke /wore out . ? Comments?

Excuse me...."Brap"....not Brad.

I'm a poor man's mechanic. My "95 300" is virtually a clone to "this." Didn't need to remove foot rests. The "50" cent sized piece that the spring is attached, front, I took my disc grinder and cut a small piece of it away to access the bolt behind it with 1/4 drive socket. Didn't need to remove brake lever. After having the two main bolts for starter out, I had fits cause I thought the starter should move left/out much easier. After losing hours of sleep over this, I tapped it with a small hammer and it rolled over and out! HalleluYAH. That, as an ending to this vid would have been appreciated. BUT, no matter, I wouldn't have been able to tackle this without your help Brad. Thanks much!!

You keep calling struts shocks.. shocks don’t have a bolt, struts do. Thanks for the video, definitely helpful

Good video of 👍🏻

I have a 2020. Can I use this same method to change the springs?

Thing to keep in mind is the amount of current drawn by the EPS you better have a healthy battery and a good charging system output.

Cambie sellos y ahora tira agua por el lado izquierdo del motor pegado ala banda

I wish I could get my EPS working. Fuse and relay are fine and there is power at the EPS unit, but it won't work. I've checked everything according to the service manual and everything checks, but nothing. If anyone has any advice, I'd appreciate it.

Not only does he make it look easy, he explains it so well that anyone can do it. Rare experience these days, thanks.

Looking forward to the 2026 trip content!

No needle and seat removal?

I’ve been working on one of these and I have a really high idle. Cannot slow it down with the mixture screws.

Screw in dipstick to check balance oil?

I have having same issue on my 2015 Polaris scrambler! Dealer is saying after flashing ECU the light stayed on and need a new EPS unit which I think is crap. I replaced the 30A Fuse, and mine has a EPS relay in fuse box but manual says its not in fuse box. Where is the location??

What a crappy video Oh please don't show us the aftermath of the finished product oh please we don't want to see that we don't want to see where the truck sits with the new coil springs what a bunch of putts

Thanks Saved me some fucking around

I'm just about to this as well, just a question, my shop manual says to oil the lip, and I notice you used grease? No difference? Just curious. THX

Hittade felet på min fågel i dag efter flera dagars felsökning, ny regulator beställd

What store did you get the 3/4-16X3 3 inch long bolt from?

1985 unit

Thank you Brad! This middle-aged lady was able to install both front wiper blades because of this video. In under 2 minutes!!! Great job showing the packages with the part numbers and explaining and demo’ing it all so clearly. 😊🙌

Great hack. Thanks!

to long buddy only have one idler pully

How often do you have to change your tire oil?

question for you, i have owned my 2003 since brand new and mine is having a slight stumble off idle and some slight erratic idling. I was pretty sure this was my issue but when i primed the system it looked perfect, not a drop came out. The bike has 8700 and was babied. The only thing i can think of is i had a battery die out just recently and being i put the battery in backwards....well i put it in forwards, it supposed to go in reverse and crossed the terminal. It did blow the 30amp fuse but now i'm wondering if that is an issue. Everything works fine, the bike runs excellent otherwise into the higher RPMs......just maybe a slight hiccup around 2500 rpm and intermittent weird idle. (not crazy but sometimes fluxuates around 1200-1500. Any thing to check?

Thanks for this, I got my 95' 300 explorer about half apart, just enough to expose the front portion of the starter and the starter isn't even engaged with the gears on the shaft. It also wiggles around, I'm no expert, but I'm guessing that means it's worn out. Anyways, now I have to take off the second half and get her out. There's quite a few steps, I'd have been shaking my head and probably throwing a wrench or 2 had I not seen this, so thanks again!

Thanks for the video. I spent some time figuring out how to replace it so many thanks for saving me time and effort 🙂

Good video other than that

I really wish you would have shown me which way to wind it up

Doesn’t work on the 2022. What a stupid feature

This procedure won't work with 5th gen 2021 1500!

Thanks for the video and I was wondering I have the one you showed, does the belt have a lot of play or is it snug ?

What size and thread pitch bolt for the puller??

Used this for a rebuild in 2024. This video walked me through bringing this old girl back. Ron Ritter sells a rebuild kit and it runs 10/10 now. Thanks!!