Thanks are you still liking it bro I'm considering the Comma x3 its on sale now.
@itmsolverАй бұрын
impressive!
@xboxice2005Ай бұрын
does the steering wheel has good torque to take tight turns? can you do end to end self drive for us with the Leaf :)
@xboxice2005Ай бұрын
when you say torque better than your other x2 cars what vehicle where they :)I'm strongly considering this device for my 2018 Leaf
@DavidKK4GAFАй бұрын
My prior Chevy BOLT and Subaru Crosstreck both needed help in sharper corners. The Leaf has no issues.
@alexkim8064Ай бұрын
Okay this is amazing. One of the only things I don't like about my EUV is no stop and go automatic resume after stop. I'm surprised this is able to work because the comma website says it only works after 3mph. I'm guessing the advanced Dragonpilot fork enables this. Do you know if the EUV will be able to do this stop and go automatic resume as well?
@DavidKK4GAFАй бұрын
I owned a Premier. Not sure about the EUV. I used a Comma Pedal with special coding.
@alexkim8064Ай бұрын
@@DavidKK4GAF Gotcha. Yeah using the pedal has a huge advantage with enabling Stop and Go functionality. I asked in the Frogpilot Discord and they said the EUV Premier would require additional hardware like a pedal or resume harness, to enable Stop and Go.
@DavidKK4GAFАй бұрын
@alexkim8064 In my prior Subaru Crosstrek they coded in a fake wheel spin to enable stop and go.
@Aaron_b_cАй бұрын
Does this work with the LT1 trim?
@rouuukАй бұрын
wouldn't it be more efficient if the input batterie voltage was higher than the output ? i mean 2s 3s 4s etc.
@DeSouzaGui2 ай бұрын
Not impressed!! Every time there is a need to change lanes, the driver seems to take the steering wheel. Again, not impressed. My subaru keeps lane like that already.
@DavidKK4GAF2 ай бұрын
Openpilot does not do auto lane changes. Needs a nudge on the wheel.
@deltonroy19042 ай бұрын
Can you build me one of these please ?
@DavidKK4GAF2 ай бұрын
The plans were online. I have changed the plate to a mass made one, that works perfectly.
@deltonroy19042 ай бұрын
Can you send me the link to it
@DavidKK4GAF2 ай бұрын
@@deltonroy1904 I can not find the original link on the web. I have a description for wiring written on the video description.
@rayslinky2 ай бұрын
Someday they'll figure out wifi, from 2010.
@richardross49962 ай бұрын
Got one recently , it is likely going back, does not do as expected.
@DavidKK4GAF2 ай бұрын
I had to increase the water pressure.
@ChaplainSparky2 ай бұрын
How are you monitoring the audio during connection?
@ChaplainSparky2 ай бұрын
figured that out.
@JoaquinCanales-q2l2 ай бұрын
its a IR laser, not fiber!
@DavidKK4GAF2 ай бұрын
Correct, the company has updated their website.
@blairhickman36143 ай бұрын
stl link? is there a part 2 where you put it together?
@HazzaALshamsi-sg4jy3 ай бұрын
what car are most compatible?
@DavidKK4GAF3 ай бұрын
Comma AI has a small suggested list on their page.
@suscups3 ай бұрын
That’s bad ass
@BrandonAbernathy4 ай бұрын
Have you ever let it come to a stop behind a car at a redlight from traffic speeds (like 45-50mph)? Does it handle it? Can it do it?
@DavidKK4GAF4 ай бұрын
Nothing I have used can see a stopped vehicle.
@KD0RC5 ай бұрын
Very cool David! Are you able to use any of the knobs and buttons to control the Flex? 73, Len, KD0RC
@DavidKK4GAF5 ай бұрын
They can be mapped. To keyboard functions.
@anitajung5 ай бұрын
Were you able to enable experimental mode?
@DavidKK4GAF5 ай бұрын
No. The Nissan Leaf controls the throttle and brake.
@Express_Cherest_EV5 ай бұрын
I installed Comma 3 on 2016 Lexus RX350 about 2.5 years ago. It enhanced the boring drive to a comfortable level, much better than the manufacturer built in ACC. I would get #Comma 3 for a Leaf with ACC if I own one. With #CCS to CHAdeMO, no range boundary and cozy Leaf EV, highly recommend. Rainy and country road, it handles very well. Close to FSD, better than Tesla TACC and AutoSteering. A family with two 2011 Leaf and one Model X. ♻️ 🚗
@DavidKK4GAF2 ай бұрын
Brother just bought a first gen Leaf.
@ryanb47775 ай бұрын
I bought the comma for my Nissan rogue and they sent the wrong harness.
@DavidKK4GAF5 ай бұрын
Comma AI customer service is very good. Did you order car harness: Nissan A? That’s the same harness for my Leaf. In the Leaf you have to remove the glovebox to get to the module.
@ryanb47775 ай бұрын
@@DavidKK4GAF yessir! holy cow you’re quick. I returned my comma but I’m going to try harness b and if it fits, I’ll order the comma again. If it doesn’t, I’ll buy a new car over this haha
@DavidKK4GAF5 ай бұрын
2018 2019 2020 only supported. On Rogue.
@ryanb47775 ай бұрын
@@DavidKK4GAF I have a 2018 that’s why I’m so confused
@DavidKK4GAF5 ай бұрын
@ryanb4777 With Propilot assist? You have to turn off the lane keep assist in Nissan to get it to work.
@David-p4s4b5 ай бұрын
Hello I just got a second hand flex with maestro and I can’t wait to remote from my boat. Nice demonstration
@DavidKK4GAF5 ай бұрын
I have TMobile and they block the remote connection. I found a working solution by using a VPN.
@TheAlleycatboy5 ай бұрын
looks perfect! Plz tell me why its a little bit warped?
@DavidKK4GAF5 ай бұрын
Anamorphic lenses can do that.
@NikitaPokryshkinАй бұрын
It’s because he install it’s wrong
@andreibaranga83125 ай бұрын
How did u update? And where to find the file?
@DavidKK4GAF5 ай бұрын
They just published a 2 update. github.com/commaai/openpilot Used Openpilottoolkit
@DavidKK4GAF5 ай бұрын
You can also update from the Comma 3.
@ChristJesus3165 ай бұрын
What does the program do and is it compatible with a 2019 Toyota RAV4 Sport Hybrid?
@SKDYCAT5 ай бұрын
Drives the car for you
@DavidKK4GAF5 ай бұрын
comma.ai/vehicles#toyota
@ChristJesus3165 ай бұрын
@@DavidKK4GAF Very cool! Thank you for the information.
@SocietyNetworking6 ай бұрын
I have a 4000 watt generator and a 2000 watt inverter and all I get are flashing red and yellow lights on the charger. It's a 22 Zero SR. Any ideas. House outlets and public chargers work fine.
@DavidKK4GAF6 ай бұрын
The generator needs a ground plug. They can be bought or made.
@gavinwilliams47256 ай бұрын
HMG poor video. you drive like a slug. you actually go over 20mph?
@wittsdd7 ай бұрын
Do you think OpenPilot would work on a 2024 Nissan Ariya? Thanks!
@DavidKK4GAF6 ай бұрын
OpenPilot supports the Propilot Assist. The Ariya has Propilot Assist 2.0. Would more than likely take custom coding.
@wittsdd6 ай бұрын
@@DavidKK4GAFthanks for the response. Actually the lower end models(engage, Venture and Empower) have Pro Pilot Assist 1.0. The higher end models have the 2.0. version. I plan to get the lower end model with 1.0 so it should be ok then right?
@DavidKK4GAF6 ай бұрын
@wittsdd Not sure. If Comma does not have it listed, it will need to be community supported. Check on Didscord. Also the harness for my Leaf is behind the glovebox.
@xboxice20057 ай бұрын
Thanks for sharing, I'm in Australia and would like one for my 2018 40kw leaf but man they are a little pricey :(
@spierce24247 ай бұрын
Would you happen to have a schematic?
@DavidKK4GAF7 ай бұрын
No. Found it online. I have upgraded to a screen control switch.
@g.56927 ай бұрын
I heard the install is more difficult with Nissans. Did you have to take the instrument panel or glove box apart?
@DavidKK4GAF7 ай бұрын
Removed the glovebox. Maybe 30 minutes total.
@N12Gautam8 ай бұрын
How is it on curves? Can it handle 60 degree turns? 45 degree? 30 degree? If on the freeway?
@DavidKK4GAF7 ай бұрын
Curves on the highway are no issue.
@a500618 ай бұрын
Does it work on any Nissan’s vehicles with propilot? Like Sentra 2024.
@DavidKK4GAF8 ай бұрын
www.comma.ai/vehicles#nissan
@ГордейДьяченко-и1и8 ай бұрын
Hello, David I received the laser yesterday and I was trying to run a test and that tiny display near the yellow test button says laser signal is off. What can be the problem? What do I have to do do switch it back on to run a test? Please let me know Thank you
@DavidKK4GAF8 ай бұрын
The top cover needs to be closed.
@ГордейДьяченко-и1и8 ай бұрын
@@DavidKK4GAF I've tested it both opened and closed - same outcome. Nothing is happening. I opened the back panel where the laser itself belongs and I saw that when I press the yellow test button the laser turns on, but it does not go through the tube all the way. It looks like the beam gets stuck right at the end and does not reach the mirror. Maybe that's the issue?
@DavidKK4GAF8 ай бұрын
@user-xv2ni5vw2e Have you reset the kill switch?
@ГордейДьяченко-и1и8 ай бұрын
@@DavidKK4GAF where is it?
@DavidKK4GAF8 ай бұрын
@user-xv2ni5vw2e the emergency twist stop switch.
@BrandonAbernathy8 ай бұрын
Do you run experimental at all?
@DavidKK4GAF8 ай бұрын
No. Will not work with the Leaf.
@BrandonAbernathy8 ай бұрын
@@DavidKK4GAF I have a Silverado with op and I'm thinking about getting a leaf as a commuter, would you buy the leaf again for op?
@DavidKK4GAF8 ай бұрын
@BrandonAbernathy yes.
@Alex100001318 ай бұрын
I just installed all the comma 3x cabling needed in my crosstrek. I noticed that i could not sit the comma device as low as you have yours with the included cable. Did you use another usbC cable?
@DavidKK4GAF8 ай бұрын
Yes. I used a different USB-C cable.
@NoName-md5zb9 ай бұрын
Knee-san
@tankmerc76329 ай бұрын
Looking into these and excuse my ignorance but do these machines have the capability to cut material or just strictly engraving
@DavidKK4GAF9 ай бұрын
They can cut. I have cut cast acrylic and wood.
@tankmerc76329 ай бұрын
Thank you for the reply@@DavidKK4GAF
@FLcruising9 ай бұрын
Does the Leaf ICC/ACC have stop & go for traffic?
@DavidKK4GAF9 ай бұрын
No. You have to press Resume.
@philippehaake61239 ай бұрын
Hello can you put a link please 73 qro HB9GUR
@DavidKK4GAF9 ай бұрын
Done
@turg779 ай бұрын
Thank you for your videos. I've just heard about all this... I have a 2020 Nissan Leaf SL Plus, and I was wondering if this will slow the car down for tight curves or is it dependent on you manually changing the ProPilot speed? Also, does it all turn on when you engage ProPilot or do you have to turn on OpenPilot separately? Thanks again!
@DavidKK4GAF9 ай бұрын
OpenPilot only controls the lateral. OpenPilot engages with CC. LKAS needs to be disabled.
@turg779 ай бұрын
@@DavidKK4GAF Thank you for the reply! So, I'm guessing even without the speed control, it's much better than ProPilot? Or, just somewhat better?
@DavidKK4GAF9 ай бұрын
@@turg77 OpenPilot is better than any other LKAS. ProPilot will disengage with the wipers on. I have used it on three cars. Over 20,000 miles.
Is there any headway to getting the radar cruise being controlled by Openpilot? It is the only reason I've been holding off from getting it for my Leaf.
@DavidKK4GAF10 ай бұрын
Have not seen any work on it. I trust ProPilot to control the throttle and brake. On other cars when longitude control was added. They had to disable the emergency braking. My first car used a Comma Pedal. It had to have the safety coding in the Panda over written.
@TroyLucia5510 ай бұрын
@@DavidKK4GAF I see. It'd have so much more capability if it did, though. Anticipating lane changes from other drivers preventing hard brakes and accelerations, traffic light recognition, speed limit changes, ugh... I guess I just live in busy areas. Wonder if we can find people who can do it!!
@DavidKK4GAF10 ай бұрын
@@TroyLucia55 With money. It takes a lot of work. And they would more than likely need a Nissan Leaf.
@TroyLucia5510 ай бұрын
@@DavidKK4GAF I imagine if they can fully hijack ProPilot, it'd work on most Nissan models. But I guess we can only dream.
@DavidKK4GAF10 ай бұрын
@TroyLucia55 I worked with the coder who made the Chevy BOLT EV. Work with the pedal. There were a lot of check engine lights. GM puts a pause in the string of code.
@floridaman72710 ай бұрын
Where does it go? Clogs have to be a nightmare!
@garfballs710 ай бұрын
Just curious, what’s your gas mileage been like on the highway while running OP? 34-ish?
@DavidKK4GAF10 ай бұрын
I no longer own a Crosstrek.
@I_Love_Planes90911 ай бұрын
Nice Timelapse!
@jamesmiller150211 ай бұрын
Did you have to load any type of mill right firmware to the black box? All my steppers are moving the correct direction. The only problem is when I run a program which is 6x6 in vcarve. It wants to run from the front left to the back right making me have to hit the emergency stop. Any ideas