Thanks Jim......ill be doing this exact job this weekend. Well shot and informative video.

you gotta take the steering wheel off to take the tumbler rodd that hits the switch under the dash

Try some Cataclean and an Italian tune up. That's what I do with my Miata. Her exhaust smells like rotten eggs, and performance suffers too, so I gotta keep my revs up.

Here is another tip. When filling from the 5 gallon or anything with a nozzle on one side of the container like a quart of oil... pour with the opening at the top so you can angle the container more for perhaps a smooth poor and less drip.

Thank you for the very detailed, informative video. Very helpful!

Oh no. My aircon technician installed it upside😢

My 2007 is throwing a P0461 for “fuel level sensor circuit A” would that be this or is that a different sensor? If it is different do you know if it’s built into the fuel pump or not? Haven’t had many problems with it but it ran out of gas while the gauge showed 1/4 tank. I deleted the code and it stayed gone for a week or so but came back today and driving on the freeway it died randomly once and it was accelerating rough. This is right after I put $40 in the tank also so I’m not running out of gas again.

was the exact info I needed to confirm I was doing the right thing, trunk is stuck and I need to move the car, thanks man!

Big fan Jim

Came here looking to do the same thing for my 2006 Kia spectra. Hopefully it's the same!

Where did u get the parts for it? Cant seem to find them

Anyone have a video/instructions on how to remove the driver seat belt buckle attached to side of a power seat?

🔴 How did this hold up two years later ❓️

Will this work on a Honda?

Mine doesn’t have those holes. Needs L hooks

I can’t believe this worked on my RX, I just got a 2000 rx300.. check engine light on for knock sensors, a vvti sensor ( p1354 ) and an air/fuel ratio code (forgot the code number). Drive the car for 2 hours back home.. noticed it was super sluggish and I didn’t have 4th gear.. would stay locked into 3 no matter how much throttle I gave it until I can to a stop and it disengage. But overall just super sluggish performance.. did this little have and all my problems went away.. got all my gears, no codes at all (drove for abt 20 miles going 55-60) and still nothing.. noticeably better shifting and performance!

Did your transmission break after you changed the fluid? I always hear mechanics talking about "your transmission will break if you change the fluid" lol

It’s bc of DOT. Discount tire doesn’t make the rules. We follow them. Doesn’t matter AWD, FWD or RWD. It’s all for safety. I hate that rule but it’s the rules we gotta follow.

P

Excellent video

You gotta pay the tip with the screwdriver. Nice 1.

Great video. I like how it's straight to the point and concise. Removed the rear seat cushions too so the back seats would fold down completely flat. ~70 cubic feet of storage capacity in that little car without the seats. Similar to a Subaru Outback with the seats folded.

Hi there, nice ML. It is possible your power steering fluid leaked on top of the AC compressor.

I'm trying to help a lady going thru some tough times. I pulled the relay and jumpered the connections and the fans ran. I tested the relay and it works, so something is not sending power to the relay to activate it to send power to the condenser fans. The compressor is coming on, but I've determined the system is leaking refrigerant. I think it's coming from the expansion valve at the firewall.

Were did you buy that on / off relay???

I'm an auto detailer and was trying forever to get the hood open on this car to clean under there. Thank you!

What if you improvised and filled these ramps with concrete so it can last forever?

Do you know where the relay can be sourced? Was it just a bad relay in your case?

Your Awesome!!! Thanks a Million my friend 😎

Dude. We know where it’s not. Just show the unlock location

Let me try that

Good trick. Wish I had a cool voice like yours!

It doesn't matter which direction you're looking at it the drain plug comes out counterclockwise

Thank You for sharing!!! 🙂🤜👍 I didn't know if the main actuator was my problem but you describe adjusting the temperature. My w16303ml500 distributes the airflow incorrectly between defrost and central vents.

one of the local guys was wheeling and forgot to turn it off, i saw the video of him getting popped with the side airbags on a hill

We had yo turn out headlights on to get it work.

The "s" puts it in slow mode, much safer to begin with! This thing takes OFF and if you're not expecting it, it can get away from you! Mine has a crack in the front from my first attempt at riding It! I got mine barely used also for $1500.

I piled up a bunch of drop cloths outside my car up to door level so most of my body was outside the car. One of my legs was up in the window.

Good job and thanks for the video. Alexandre (Rio de Janeiro).

For the people saying to chock the front of the rear tire… chocks come in pairs for a reason. You chock both the front and the rear of the same tire.

I live at East Wenatchee

thats a nice looking truck man!

Thanks for the idea I appreciate it just had my Pelican gave it to me for free and I'm psyched about it I'm going to set this thing up

Thanks for posting the video Jim. Very helpful. Did your RX have the tow package before you plugged in the part referenced in the video? My RX350 has the white connector like in your video, and 30amp tow fuse, but I am trying to determine if I also need a converter module to power the trailer lights.

Car was idling crazy got it fixed for $28 bucks thanks for the video.

Fuking Dodge , I hate this kind a car

I dint trust that wheel just hanging even if the brakes are engaged

Appreciate the video thanks fam!

Have same Metal mesh Matrix in My Saab Catalytic. It's Horrid stuff to work with. Ceramic Matrix types... shatter /come apart /out with only a few minutes work. Tried to core out the centre First... but Spade bit drills.. Don't work ...Neither do Hole saws. Only ruined the bits. Crow bars (many sizes and weight)..simply dents the stuff. Considering a Long 16" Chisel head on my Air Hammer. Might ? work . Problem is it's ~50$ to buy . BUT having a shop weld in a straight pipe in place of the Catalytic would cost similar.

Great video. I ordered a filter and fluid for my 33 ton troy bilt a few months ago. I plan to drain and replace this week. I mine as well replace the engine oil and spark plug while I'm at it.