Kaip.jums nulakavus gaunasi veidrodinis atspindys,du kart lakavau ir jis matinis kazkoks, ne poliravimas nepadeda. Patarimu ka darau netaip? Aciu
@HELVINAltd14 күн бұрын
Sveiki, tiksliai atsakyti negalime, nes priežasčių yra ne viena, bet greičiausiai buvo padaryta klaidų paruošime, ar dažyme. Rekomenduojame laikytis visų medžiagų džiūvimo, storio, sluoksnių reikalavimais. Naudoti suderinamus produktus. Nekaitinti ir nedžiovinti medžiagų tiesiogiai prieš saulę. Dažyti ne paruoštais dažais, o užpildomus į aerozolį.
@Coa_Kralj_Coa_The_King3 ай бұрын
We understand everything 😂😂😂
@gabrysgabriukas4 ай бұрын
Ačiū! pagaliau jau aiškiau kas tai per dalykas. 😊 Prašau daugiau tokių video, ypač pradedantiesiems! step by step
@Evilolex4 ай бұрын
sadly not in english but still very helpful
@ناصرابوالنصر-و9ح5 ай бұрын
عيذ واحد في مصر
@MmazharKhan-b3u6 ай бұрын
Sir please ph no send me
@Faizcrafts6 ай бұрын
I want to buy this product
@nerijuskubilius96268 ай бұрын
Sveikas, galima tepti špaklių ant pliko metalo ar prieš tai reikalinga su gruntu prapūsti?
@HELVINAltd8 ай бұрын
Sveiki, Taip, glaistą galima tepti ant pliko metalo. Tepti reikia iškart po šlifavimo. Jeigu glaistas bus tepamas ne iš karto, būtina prieš tai užgruntuoti, nes net ir palikus pliką metalą trumpai, dėl ore esančios drėgmės gali prasidėti korozija. Tai ypač svarbu po smėliavimo, suvirinimo darbų, detalių tiesinimo.
@piotrrajdek33778 ай бұрын
Why add mipa wbc beispritzlack??
@HELVINAltd8 ай бұрын
It is used to get better looking mirror glaze finish. It helps to avoid partial dissolution of the basecoat.
@tbradaric6 ай бұрын
@@HELVINAltd Did you mix beispritzlck together with Mipa Vicrom in your paint bucket or you sprayed it separately?
@tbradaric6 ай бұрын
kzbin.info/www/bejne/bImugqeDd86bfMUsi=KM38Hsy1PiONyCdm&t=61 Here it looks like Vicrom is still inside while you adding Beispritzlack
@HELVINAltd6 ай бұрын
@@tbradaric No, you have to spray it separately.
@tadasanelauskas14119 ай бұрын
Sveiki. Tas flash off laikas 3-5 min galioja tik kamerose? Ar pries purskiant antra eile jis turi buti sausai lipnus? Nes pagal tai turiu islaukti 40min garaze prie 15 laipniu. Ar galima antra eile purkti dar ant gyvo pvz po 10-15 min mano salygom? Nors nelabai tiketina . Pas jus kameroje pries purskiant antra eile, pirma eile buna jau sausai lipni po 3-5min?
@HELVINAltd9 ай бұрын
Sveiki, flash off laikas gali skirtis priklausomai nuo temperatūros, santykinio oro drėgnumo ir oro srauto. Lakuojant garaže prie 15 laipsnių, antrą lako sluoksnį rekomenduojame purkšti ne anksčiau kaip po 10-15 min. Laukti, kol bus sausai lipnus, nereikia.
@vygantasrimkus263210 ай бұрын
Sveiki,kaip vadinasi ši kaladėlė su kuria sušveitėte laką ir kur nusipirkti,ačiu.
@HELVINAltd10 ай бұрын
Sveiki, kaladėlė vadinasi Kovax Toleblock. Įsigyti Kovax prekių galite čia: www.helvina.lt/lt/jxsearch?search_categories=2&search_query=Kovax&jx_submit_search= Ačiū, kad domitės!
@GaryTaylorvw11 ай бұрын
Can I use this on bumpers as well as body or do I need a promotor first ?
@HELVINAltd11 ай бұрын
Epoxy filler are best on bare metal because it has very good adhesion and corrosion protection. On bumpers we recomend to use Mipa Multifiller, or Mipa acrylfiller 4+1.
@GaryTaylorvw11 ай бұрын
@@HELVINAltd yeah just a bit confused of everything I need, I’m respraying my vw transporter and doing an engine swap, wasn’t originally planning on painting it but doing a full engine and loom swap so vans gutted out was just going to paint the facelift parts the same as the rest but decided to change the colour while I’ve got it off the road, the bumpers are all painted at the minute so I’m just changing the colour but taking the metal back to bare for smoothing it out before painting and getting rid of any rust, I’ve got all the fillers, 2k paint and primers, thinners, hardeners etc just wasn’t sure if i could use 2k primer that’s going on top of the epoxy directly onto the bumpers after sanding them or needed to use a plastic primer then paint… was thinking of no change in colour shade throughout the van if using different primers for bumpers… I probably could of explained better 😂 but I’m obviously a newbie to painting especially a van
@farelamore Жыл бұрын
It looked good before the 4th layer
@Vilius19971 Жыл бұрын
Sis lakas turi tendencijos temptis ar ne?
@HELVINAltd Жыл бұрын
Sveiki, šis lakas džiūdamas nesikeičia. Tai yra kaip išsiliejo, taip ir liks po išdžiovinimo.
@Vilius19971 Жыл бұрын
@@HELVINAltd gal rekomenduotumet kazka garazo naudojimui, kuris turetu tendencijos pasitempti ir greit dziutu?
@HELVINAltd Жыл бұрын
@@Vilius19971 Rekomenduojame pabadyti Mipa CX2. Šis lakas labai gerai tinka garažo sąlygomis.
@rimka11 Жыл бұрын
Čia jie gal pas mus gaminami?
@VladimirasKorolkovas Жыл бұрын
Koks jusi agresas
@HELVINAltd Жыл бұрын
Sveiki, mūsų įmonė užsiima tik automobilių kėbulo dažymo reikmenų prekyba. Remontų nevykdome. Patikusias priemones kviečiame įsigyti www.helvina.lt, arba užsukti į mūsų parduotuves Vilniuje, Kaune, Klaipėdoje ir Panevėžyje.
@Sarfrozkhan Жыл бұрын
is it possible to ship it india ???
@Gegsite Жыл бұрын
Wow now thats slow
@skirmisskr4587 Жыл бұрын
Kiek kainuotų toks turiukas? Pats galėčiau vairuot? :D
@HELVINAltd Жыл бұрын
Sveiki, keturračių turus organizuoja ciongo.lt
@chilik793 Жыл бұрын
Химическая металлизация не лучше будет?
@HELVINAltd Жыл бұрын
лучше
@micastojanovic7115 Жыл бұрын
SRANJE
@leagueboost49612 жыл бұрын
Ačiū už naudingą informaciją!
@zeckendreck2 жыл бұрын
i have a vaupel 3500 SNK .. but i am not happy because its nearly not posible to take in parts and clean it ..... how it looks by the SOLL?
@HELVINAltd Жыл бұрын
With Soll seam sealer gun you don't need clean it after work. Just close fan and fluid tip to prevent air come in to the system. Always keep seam sealer inside cartridge.
@yayakyartu20612 жыл бұрын
Как сделать логотип на баке , бак должен быть уже в лаке ? Или только база если база трафарет как на нее клеить оторвётся ведь потом с краской
@JustinAzeiMusic2 жыл бұрын
Super! O kiek laiko turi praeiti po dazymo iki lakavimo? Ir kokie tarpai tarp lakavimo?
@HELVINAltd14 күн бұрын
Sveiki. Po dažymo turi praeiti ne mažiau kaip 15 min. Tarp pirmo lako sluoksnio ir antro lako sluoksnio 5 min.
@bluesmaster98962 жыл бұрын
Hi I'm spraying my motorcycle frame with this primer in an aerosol it's 2k with active hardener . How long should I wait to apply the paint coat please . Is there a time limit ,in other words can I leave it overnight before spraying a paint coat over the primer coat ,thanks.
@cs57992 жыл бұрын
shiit mipa cc8
@ARIASPHIL1232 жыл бұрын
It will nice if can explain better all adjustments on gun and pressure.
@rajeshprajapati72552 жыл бұрын
I want to buy this model in india give the option
@marinrims2 жыл бұрын
very cool please tell me, If the wheel is hanging on a hook, how to paint so that the paint does not flow?
@HELVINAltd2 жыл бұрын
Thank you. You have to look at light. Light on the painting surface shows how paint lays on it. Every time you have to control your distance, speed, passes, etc...
@marinrims2 жыл бұрын
@@HELVINAltd thanks)
@marinrims2 жыл бұрын
@@HELVINAltd paint goes well, but lacquer does not , flowing
@HELVINAltd2 жыл бұрын
@@marinrims It's becouse small fluid tip. Reduce your clearcoat to have 16s. by DIN4 viscosity cup
@ellisstotzel47962 жыл бұрын
Can I tint with solvent base coat??
@HELVINAltd2 жыл бұрын
Yes, you can tint with solvent base coat. For better coverage, use wet on wet primer.
@Gegsite2 жыл бұрын
Please make English subtitle for the videos! Superb video! From a mipa fan. Thanks!
@firasismael62622 жыл бұрын
When we can buy it please
@HELVINAltd2 жыл бұрын
Contact us by email and we will find a way how to deliver to you.
@kotauto36292 жыл бұрын
Šimtai mašinų tip pdaryta ir parduota 👌
@eviljoker3032 жыл бұрын
15psi?
@HELVINAltd2 жыл бұрын
Spraying pressure 1.5 bar (22psi)
@ANDY-we7mr2 жыл бұрын
what size fluid tip and the settings helps people out ..
@krzysztofjakubczak71072 жыл бұрын
Super pistolet
@virgisaugis19862 жыл бұрын
uz tokia halltura, tik per spranda.
@HELVINAltd2 жыл бұрын
Taip nudažytos automobilio dalys daugiau kaip po metų eksploatacijos atrodo puikiai. Dažant automobilį su aerozoliais pasirinkite tinkamas medžiagas.
@maxmeyer742 жыл бұрын
What size fluid tip?
@HELVINAltd2 жыл бұрын
Fluid tip size 1.3
@westvanners3 жыл бұрын
Tested. If you want chrome, this is not for you. Just a shiny silver.
@karenwilson25633 жыл бұрын
This is great thank you for making this video, it's really well done. Karen
Hi! The compressor at 1:53 its not enough to run this spray gun?
@johnallen86803 жыл бұрын
It looked quite promising mid way through the video, but by the end it looked more like a clear coated silver than 'Chrome'.. I'd like to think it was the lighting.. Would have been good if someone had took it outside. The stills of the car mirrors did look convincing though.. I will think on...
@mohammedal-otaibu51563 жыл бұрын
Where is the website or link to buy?
@HELVINAltd3 жыл бұрын
What country are you from?
@KrC_Games3 жыл бұрын
sveiki, kaip tik radau pas jus www.helvina.lt/en/aerosol-primer/2186-soll-1k-epoxy-primercolor-grey-400ml.html
@KrC_Games3 жыл бұрын
ar tiktu sitas gruntas ant xpower grey spalvos?
@KrC_Games3 жыл бұрын
ir ar rudziu surisejas su cinku tinkamas aerozoliniam dazymui?
@mantassimkus24523 жыл бұрын
@@KrC_Games Soll 1K epoksidinis gruntas puikiai tinka prieš dažymą tiek dažant su aerozoliais, tiek prašveistom vietom užgruntuoti dažant su pulverizatoriumi.
@mantassimkus24523 жыл бұрын
@@KrC_Games Paprastai po rudžių surišėjo panaudojimo, remontuojamą vietą reikia užgruntuoti ir tik po to uždažyti.
@KrC_Games3 жыл бұрын
@@mantassimkus2452 labai dekui uz reply! o gal zinot ar uztenka p600 popieriaus, silpno pasveitimo dazant tos pacios spavlos detale(jeigu norint pasalint kelis ibrezinus)
@soltam54573 жыл бұрын
What pressure did you use for this paint job?
@HELVINAltd3 жыл бұрын
Spraying pressure 3 bar.
@ramunera35703 жыл бұрын
Jauciu daug dulkiu gavosi nes vejas lauke
@HELVINAltd3 жыл бұрын
Dulkių buvo minimaliai, bet geriausiai dažymo darbus lauke atlikti po lietaus. Tada dulkių būna mažiausiai.
@kotauto36292 жыл бұрын
Plonas sluoksnis nesimato
@rafaeltrejo3773 жыл бұрын
Buen video, la técnica tiene mucho que ver, que presión es la recomendada?, te lo agradeceria. Saludos desde la City México.
@HELVINAltd3 жыл бұрын
Hi! Thanks for watching! Spraygun in the video is DEVILBISS PROLITE. You may know it as TEKNA in your country. Air pressure - 2.0 BAR