Пікірлер
@injectx
@injectx 15 минут бұрын
I've watched many Mojave GROM videos but you're the first that actually knows how to drive it and actually land it. Made me purchase one!
@oldschoolracer6357
@oldschoolracer6357 22 сағат бұрын
Any idea what your top speed is with this set up? Awesome build by the way!
@richduperbash2966
@richduperbash2966 20 сағат бұрын
Thanks Brother 👊. I recently hit 66 mph before blowing a rear tire. That was going into the wind. She's pretty fast with this setup. Could gear up a tad, but I'm happy with 42/39 🍻
@mazpr2025
@mazpr2025 Күн бұрын
I think stock is 50t spur.... not 52t
@richduperbash2966
@richduperbash2966 Күн бұрын
Stock spur has been 50T for years. ARRMA also makes a 46T option.
@mazpr2025
@mazpr2025 Күн бұрын
@richduperbash2966 2:32 I think it overlaps, sounds as if you are saying fifty two, unless it is fifty tooth... 🤣
@richduperbash2966
@richduperbash2966 Күн бұрын
Yeah it's probably my voice 😂
@Wild_Bill_RC
@Wild_Bill_RC 2 күн бұрын
Rich great vid! Quick question for anybody’s opinion. Just picked up possibly last EXB Kraton 6 from hobby shop and did not run it yet but immediately threw a 18t pinion in. Is that a bad idea? Gonna have issues? Still all stock other than pinion swap 🤘🏻
@richduperbash2966
@richduperbash2966 Күн бұрын
You should be fine temp wise during winter with the 18T. I'd just watch your temps come summertime depending on how hot your ambient temps get. Much past 150F motor and 140F ESC is getting toasty.
@Wild_Bill_RC
@Wild_Bill_RC Күн бұрын
@ Thanks for response Rich! Sounds good 🤙🏻
@rcsmith5909
@rcsmith5909 2 күн бұрын
This is a great build man.👍🏼🔥 nice run
@richduperbash2966
@richduperbash2966 2 күн бұрын
Thank you Brother 👊
@Richard-nv4sn
@Richard-nv4sn 2 күн бұрын
That's freaking awesome I have had my 3s granite blx for almost 2 years and it still rocks fast as hell and it alot of good control mine started as the mega version i have upgraded my truck with version 3 blx parts I bought the brushed one because it was 100.0$ cheaper I already had the same blx100 power system arrma Rocks I going 4 THE MOJAVE 4s NExt
@psiturbo
@psiturbo 3 күн бұрын
The guy does a FY review, states it will not be for bashing, more of a driver's rig. A few months later, sending it to the moon! 🤣 The rear shafts should be level under acceleration, so slightly just a little bit higher standing still. Because if it is level when accelerating if leveled, it will be under.
@boomerak4774
@boomerak4774 3 күн бұрын
Nice run! That xrt is a beast. I’m going to be putting a hobbywing 1250kv g2 with a max 6 esc g2 in my xrt, I’m going for lots of torque and good speed what gearing do you recommend? I was looking at 21/35 setup
@richduperbash2966
@richduperbash2966 2 күн бұрын
Thank you Brother 😁. I think 21/35 sounds like a good starting point. I haven't ran the g2 1250, but you should have plenty of speed.
@boomerak4774
@boomerak4774 2 күн бұрын
No problem brother and appreciate you! Keep the good content coming
@miasam9666
@miasam9666 3 күн бұрын
Distant memories of watching this and buying the senton 3s by the time covid hit. This truck started it all for lots of people it seems, including me. Great rc car
@richduperbash2966
@richduperbash2966 3 күн бұрын
Yes indeed Brother 👊. The Senton 3s is a fantastic rig. So many great times with this SCT 😍
@miasam9666
@miasam9666 3 күн бұрын
@ i want to raise my senton abit after installing granite wheels and typhon a arms. Does the typhon v2 shocks raise the senton? Or should i go with the non branded big bore shocks? Thanks bro
@richduperbash2966
@richduperbash2966 3 күн бұрын
The Typhon 6s shocks are far more adjustable including preload and ride height. The Typhon 3s arms are quite a bit wider. Hopefully that will work out with the Senton SCT body.
@Sheldinator
@Sheldinator 4 күн бұрын
spiral diffs or stock? keep breaking mine with same setup
@richduperbash2966
@richduperbash2966 3 күн бұрын
My Vitavon spiral gears have been absolutely flawless in my XRT. Beyond that, they're smoother, faster, and sound awesome. I no longer have any worry about stripping gears.
@Sheldinator
@Sheldinator 3 күн бұрын
​@@richduperbash2966but in the xmaxx here, what where you using?
@richduperbash2966
@richduperbash2966 3 күн бұрын
That's using stock gears. They fail semi regularly. The stock main gears are junk in these rigs. Can't wrap my head around an 8s size car not having hardened steel gears.
@Sheldinator
@Sheldinator 3 күн бұрын
@@richduperbash2966 any other diffs you recommend other than vitavon which vould be more budget friendly
@ryanpowell2908
@ryanpowell2908 5 күн бұрын
Hello mr.rich, so i have a very heavily modified kraton 6s exb v2 that has every m2c part offered plus many other top tier upgrades as it is a full custom build. Only thing stock is the esc and motor, but I just purchased a max 6 combo with the 4990 1650kv motor to put in it. It's definitely heavy now. Wanted to know what pinion size you recommend? I have a similar driving style as you with big airs and also like laying down the throttle on big stretches. Also what diff fluid do you recommend on front,center, and rear? And pinion ?
@RcPlayer-tt2vw
@RcPlayer-tt2vw 4 күн бұрын
Think I use 26 27t Robison with that set up but that’s with mojove smaller wheels than kraton but still say somewhere between 23 and 27 think going get new kraton today , I have old exb I didn’t use I could throw that set up in .
@jake4194
@jake4194 5 күн бұрын
How do you only have 27k subscribers?! This is some of the most entertaining RC driving I've seen on you tube!
@richduperbash2966
@richduperbash2966 5 күн бұрын
Thank you Brother 🤗. My channel has been a slow grower. Truly appreciate the kind words. 🍻
@iamgeek01
@iamgeek01 5 күн бұрын
I might be late but how does the ground clearance and handling compare to a Typhon 6S?
@richduperbash2966
@richduperbash2966 2 күн бұрын
The Mojave 4s has decent ground clearance and handling for an SCT or desert racer. Tons of shock travel overall. The Typhon 6s is a superb handler and incredibly fast by comparison with it's low center of gravity. It's almost unfair to compare as they're completely different designs.
@iamgeek01
@iamgeek01 2 күн бұрын
@ Looks like a typhon 6s is my next rig😁
@travispratt6327
@travispratt6327 5 күн бұрын
Typhon, not Typhawn. Sorry, was bugging me.
@jamespringle9821
@jamespringle9821 5 күн бұрын
I have the 4s model awesome, my outcast 8s came today
@richduperbash2966
@richduperbash2966 5 күн бұрын
Congrats James 😱. The O8s is a monster!!! So much fun with awesome potential.
@GreatLakesRC
@GreatLakesRC 6 күн бұрын
So awesome Rich! I always love seeing you drive at the skatepark 🤩
@richduperbash2966
@richduperbash2966 5 күн бұрын
Thank you Brother Aaron 🤗. The skatepark has been a super fun option with recent rains. Truly appreciate it!!! 🍻
@richardbrown9138
@richardbrown9138 6 күн бұрын
Absolutely an adrenaline blast!!! God bless!
@richduperbash2966
@richduperbash2966 5 күн бұрын
Thank you Richard 🙏🤙🤙
@gavingowing7572
@gavingowing7572 6 күн бұрын
What is the best esc for Traxxas maxx?
@richduperbash2966
@richduperbash2966 5 күн бұрын
The Hobbywing Max8 is a direct fit, easily programmed, with enough power to move her nicely. It gets my vote.
@ek2588
@ek2588 6 күн бұрын
Hey rich awesome vids as always. Quick question, if i was to get the new kraton 6s non exb version. What would you recommend as first essential mods for longevity?
@richduperbash2966
@richduperbash2966 5 күн бұрын
Thank you Brother 🤗. Aluminum chassis braces are a must front and rear. Beyond that, aluminum rear suspension mounts (C and D blocks) and an aluminum upper front suspension mount are highly recommended. There's typically a fair amount of collateral damages when these parts fail depending on the speed and energy involved.
@Captinfun101
@Captinfun101 6 күн бұрын
Hey Rich , I finally found a vid again , I’m sure you’re posting, but I’m not receiving. And I have to say the 6s exb is by far the best all round big air , big fun . Hope you had a good Xmas and new yr . Ps, your loop d loops are fire at that skate park except that one ding 😢
@richduperbash2966
@richduperbash2966 5 күн бұрын
Thank you Brother 🤗. KZbin notifications are super inconsistent I've noticed. Yeah this rig is such an awesome all around basher 😍. Had a great Christmas just can't believe 2024 is here and gone already 😂. The O6s was due for an alloy front bulkhead. She's good as new and stronger than ever. 🍻
@sethdale4721
@sethdale4721 7 күн бұрын
I guess it’s a strange thing to say to another man but you are really friggin good at driving these things. I told my wife if me and my buddy went to a skatepark with ours we may get 2 minutes of drive time combined haha
@richduperbash2966
@richduperbash2966 6 күн бұрын
Thanks so much Brother 🤗. Yeah the skatepark is a brutal environment. I've had my share of quick breakages no question 😂
@weedfaya959
@weedfaya959 7 күн бұрын
Super controle du camion , big up 👍
@AldoLoyal
@AldoLoyal 7 күн бұрын
What an awesome car Rich definitely the best out there for the money. It’s hard to beat that car. I believe this is the only RTR I have. That’s still pretty much stock. Those ramp sends at the end of the video were awesome. That was the best part for me. Looked like you took a nasty hit on one of those. Hope the car survive awesome video as always, brother 🚀💪✌️👊👊
@richduperbash2966
@richduperbash2966 7 күн бұрын
Thanks so very much Brother Aldo 👊. Yeah the EXB was a huge step up for ARRMA RTR's. The windstorm ramp sends were sketchy as heck 😱😂. My K12s lost both left hinge pins and the alloy A block grenaded. Steel for the win 💪
@slicktmi
@slicktmi 7 күн бұрын
Hey rich did arrma finally update their ring and pinion on the diffs? Last arrmas i had was the v3's and i was always shredding diffs shimmed or not. Kinda considering getting the exb but not if the diff problem hasn't been updated
@richduperbash2966
@richduperbash2966 7 күн бұрын
Well the V6 RTR models come with EXB diffs. This might be the new updated norm with the 6s rigs.
@slicktmi
@slicktmi 5 күн бұрын
@richduperbash2966 awesome i seen that in a video but wasn't sure thanks rich!
@wadebarnes6720
@wadebarnes6720 8 күн бұрын
I am very new where did you get your skid plate at
@richduperbash2966
@richduperbash2966 7 күн бұрын
That's from M2C Racing online. They're based in South Carolina and take tremendous pride in their products 😍. m2cracing.net/shop/shop.php#!/M2C-3056-KRATON-6S-SKID-PLATE-BRACE/p/683908893/category=161585845
@wadebarnes6720
@wadebarnes6720 7 күн бұрын
@richduperbash2966 in the same state I live in
@wadebarnes6720
@wadebarnes6720 7 күн бұрын
@@richduperbash2966 I bought the same car that you have haven't got to use it yet cuz it was broke when I bought it and they're sending parts for it now
@tittentei7331
@tittentei7331 8 күн бұрын
Love your driving❤🙌✌
@richduperbash2966
@richduperbash2966 7 күн бұрын
Thank you Brother 🙏
@tittentei7331
@tittentei7331 8 күн бұрын
Nice Bro... Have sold my Kraton v5 so i can buy v6 or this:) What will you say is best? With the prize in mind!🙂👊👍
@richduperbash2966
@richduperbash2966 8 күн бұрын
The EXB RTR has clutch upgrades the V6 doesn't (alloy bulkheads, alloy chassis braces, stronger 7075 towers, and upper front alloy suspension block). That block and the chassis braces are a must. The bulkheads alone are a supreme upgrade. My pick is still the K6s EXB RTR.
@tittentei7331
@tittentei7331 6 күн бұрын
@ Thanks Bro👊🙂 Then i go for that RC!✌
@DON-JULIO-FISHING
@DON-JULIO-FISHING 8 күн бұрын
Where's orange darling
@richduperbash2966
@richduperbash2966 8 күн бұрын
Orange Darling will be out again soon I promise 😍
@ElStriker777
@ElStriker777 8 күн бұрын
🔥👍
@rcbabou7544
@rcbabou7544 9 күн бұрын
Vous êtes le boss 🫵🏽 du Bash 🎉 j'ai une petite chaîne youtube 😅😅
@richduperbash2966
@richduperbash2966 8 күн бұрын
Thanks so very much my friend 😁. Truly appreciate the kind words 🍻
@justonjacoby4455
@justonjacoby4455 9 күн бұрын
Great Job on bashing and the video man!!
@richduperbash2966
@richduperbash2966 8 күн бұрын
Thanks so very much Brother 🤗
@alankowalski8781
@alankowalski8781 9 күн бұрын
Rich, what about RPM A arms? Would they hold up better?
@richduperbash2966
@richduperbash2966 8 күн бұрын
Unfortunately the V5-V6 style RPM arms turned out to be a failure 😢. The rears break in the same spot over and over. I went through 4-5 sets and gave up.
@alankowalski8781
@alankowalski8781 9 күн бұрын
Agreed, perfect no, the best value for an RTR yes, especially if you aren’t building from scratch.
@richduperbash2966
@richduperbash2966 8 күн бұрын
Yeah there's really no perfect RTR, but they did a great job with it overall. 🍻
@aqualungs77
@aqualungs77 9 күн бұрын
I have the EXB Kraton V2 and can't wait for spring. Do you think 300k is too much for the center diff with LSD? I shimmed all the diffs, M2c Droop screws, skid plate, Schorched Knuckles.. that's my baby.. Then I had to order a new Notorious V6.. which I will beat on and run on the dandy beach lol.. so I agree after taking apart that one and shimming diffs.. not only are the aluminum housings worth it.. EXB you also get Aluminum Chassis braces, upper front hinge mount, center diff mount.. wheras V6 are plastic.. So far I've upgraded those parts with ADU. If you want V6 hubs, that's a 20 upgrade and bearings.. no sweat. So the value is there.. Glad I bought the EXB before it was discontinued 😊
@richduperbash2966
@richduperbash2966 8 күн бұрын
I think 300k LSD will work just fine 👍. Yeah the EXB RTR is a solid value with the housings and other hop ups no question. They're still available on Amazon last I checked. It's great there's so many aftermarkets offering needed upgrades. Plastic chassis braces are a liability 😱. So prone to failure and collateral damages.
@deezrcz
@deezrcz 9 күн бұрын
Incredible session as always! It’s so unfortunate Arrma discontinued this model. I don’t get why.
@richduperbash2966
@richduperbash2966 8 күн бұрын
Thank you Brother 👊. Yeah I don't know why other than to limit people's purchase options. The EXB RTR is still available on Amazon last I checked. I say bring the Senton and Talion 6s back 😍. Perhaps Horizon has some sort of minimum sales quota we don't hear about.
@beman87
@beman87 9 күн бұрын
How do you rate this against the 6s kagama?
@richduperbash2966
@richduperbash2966 8 күн бұрын
I don't have a Kagama to keenly compare, but it's a step above from what I've seen and heard online.
@UAERCADDICTS
@UAERCADDICTS 9 күн бұрын
Amazing bash like always
@richduperbash2966
@richduperbash2966 8 күн бұрын
Thanks so very much Brother 🙏
@FLPatrick1095
@FLPatrick1095 9 күн бұрын
Cant go wrong with a K6. Admittingly the stock diffs need some work. The pins/outdrives are prone to breaking still.
@richduperbash2966
@richduperbash2966 8 күн бұрын
Agreed Brother 👊. Yeah I can't help, but wonder if ARRMA will slowly phase out the traditional diffs for EXB ones.
@dazofthemoo1531
@dazofthemoo1531 9 күн бұрын
Haha. You got the best laugh. If you basher doesn't come with laugh included (0:24 + 4:11), you've got the wrong car.
@richduperbash2966
@richduperbash2966 8 күн бұрын
Thanks so very much Brother 😂. Gotta have fun and get some laughs in out there. 🍻
@B.K._BerndK.
@B.K._BerndK. 9 күн бұрын
Rich Very nice bash bro 💪🏻🤩👍🏻🤜🏻🤛🏻
@richduperbash2966
@richduperbash2966 8 күн бұрын
Thank you Brother 😎💪👊👊
@ch-vs3fw
@ch-vs3fw 9 күн бұрын
Straight up gracefully throwing down at the skate park, damn!
@richduperbash2966
@richduperbash2966 9 күн бұрын
Thank you Brother 🤗. Good times with friends 🍻
@buttcheakyo
@buttcheakyo 9 күн бұрын
Hi rich I got a v5 Kraton thanks to your videos! It has a bunch of exb and a few M2C goodies! Hop to get a exb some day!
@richduperbash2966
@richduperbash2966 9 күн бұрын
That's awesome Brother!!! The Kraton 6s is a must have in whatever form suits your taste 👊. Such a killer all around basher. 🚀🚀
@randylivengood3112
@randylivengood3112 9 күн бұрын
You’re tempting me to take out my 10 year anniversary Outcast out for its maiden run! I don’t have the skills to do it justice!
@richduperbash2966
@richduperbash2966 9 күн бұрын
I say go run her Randy 🤗. Life's too short not to knock the dust off stuff and have fun!!! 🍻
@randylivengood3112
@randylivengood3112 9 күн бұрын
@ I suppose you’re right. I just got into the hobby and got this thing a month ago! A little more practice on the Granite and I’ll get her airborne soon!
@itsamk18-ish
@itsamk18-ish 9 күн бұрын
Glad I’m not the only one not super impressed by the maxx, ive had nothing but issues with mine. Mine was v1 but i just did the v2/widemaxx conversion to it. It’s super cold here right now so I’ve only ran it once since swapping it,it seems to be a bit better but i haven’t ran it real hard. I’m only running it on 4s, i may upgrade it to run 6s but then i imagine I’ll just have different issues to deal with lol. It sucks because i love my xmaxx and hoped the maxx would be tougher since it’s smaller. I’ve been wanting a fireteam for awhile, might have to get one of them and run it against the maxx
@richduperbash2966
@richduperbash2966 9 күн бұрын
Yeah my buddy John was constantly busting front bulkheads with his V1. Mine has been fairly solid, but I kept blowing through gears and lost interest. 6s isn't too crazy considering the weight of this rig is equal to lots of 1/8 scales. The handling isn't great, but I'm confident my gear issues are over with this mount 💪. The Fireteam is wicked fun no doubt 😍. The 1/7 wheelbase is perfect for highspeed fun with solid control. It's one of the funnest rigs I've ever bashed. 🍻
@Kevin-dutch-rc
@Kevin-dutch-rc 9 күн бұрын
Great bash again Rich and nice to see the maxx again. My maxx also keeps breaking gears and maybe this is the solution from m2c! I'm curious how it will work out in the long term. See you again in the next video!👍💪🚀
@richduperbash2966
@richduperbash2966 9 күн бұрын
Thanks so much Kevin 🤗. Yeah I was planning to run my Maxx, but realized the packs I use (that fit) were going out with bad cells. This mount has worked awesome for Aldo Loyal and others so I'm confident in the design. I'll get her back out soon. 🍻
@Kevin-dutch-rc
@Kevin-dutch-rc 9 күн бұрын
i'm looking forward to it🍻
@bennovak4182
@bennovak4182 9 күн бұрын
Hands down rich is the hardest and most Finesse driver I've ever seen. Man, the **** that you pull off is just insane. I tried to send it like you do man, but my budget doesn't let me *******. Follow through. But I enjoy watching you do it man, great job. It's awesome seeing what's capable. With these rigs.
@richduperbash2966
@richduperbash2966 9 күн бұрын
Thanks so very much for the kind words Ben 👊. I try to respect these rigs while testing their limits the best way I know. Truly appreciate it Brother!!! 🍻🤙🤙
@devinwilson2524
@devinwilson2524 9 күн бұрын
Hey rich what would cause my main input gear to grind on and around my diff case?? No shim behind input gear but metal shavings from diff is inside the housing.. cant seem to find the clicking sound when inspecting the rig..only when under power it clicks yes it’s the rear n that’s way I noticed the shaving but no teeth are missing and diff are brand new..check the front still looks good just the rear dig is now two tone?? I need help bro. Yes I still have stock bulkheads.
@richduperbash2966
@richduperbash2966 9 күн бұрын
Clicking usually comes from teeth skipping. I only use shims on the crown gear side bearing. That brings the crown gear closer to the input. Metal shavings indicate a problem no question. Make sure your bearings are all good and the teeth aren't worn and that the output cup hasn't floated forward off the input shaft. If you have the plastic stock bulkhead, make sure to inspect carefully for cracks including on the bottom. A cracked bulkhead will allow the gears to slip. Hope you get it sorted Devin. 🍻
@devinwilson2524
@devinwilson2524 9 күн бұрын
@ thanks bro just trying to make my rigs durable like yours..learn everything I know kinda from you!! just goin in your foot path.
@richduperbash2966
@richduperbash2966 8 күн бұрын
You bet Devin 👊. I should add that "clicking" usually means 1-3 missing or badly chipped teeth and "grinding" on throttle usually means slipping teeth. Of course these are just descriptives. I know you mentioned no missing teeth.
@devinwilson2524
@devinwilson2524 7 күн бұрын
@ yea all new diff’s.. I’m just going to to wait till I get my hands on some cash for some aluminum bulkhead..don’t want to keep running it till the problem breaks then I’ll find it then but more money but thanks brother
@jessejames2546
@jessejames2546 9 күн бұрын
So your stock Maxx motor handles 6s well? I’m rebuilding mine, swapping to the longer chassis, v1 to the modern chassis, I’m using a vxl 8s esc, was gonna throw my old v1 Arrma 6s motor in but if the stock works I’ll use it
@richduperbash2966
@richduperbash2966 9 күн бұрын
Yeah mine has taken 6s no problem, but the Traxxas mounting screws are only M3 vs M4 with the BLX ARRMA motor. With this M2C mount, there's the 2 standard hole face plate. In essence, I'm not sure the screws will snap off the motor. Time will tell. The old BLX motors rip hard 😍
@jessejames2546
@jessejames2546 9 күн бұрын
@ nice