Know quiet element 11 inch? Low density non kettling

Where can I get one of these from. I have tried Ebay, but when I put details, it comes up with this will not fit my vehicle.

Great video and advice

A really great video thank you. Can I ask when you had cut the double skin leaving an open cut at the top what did you do to stop dirt and water getting into that area so the rush does not just start there?

just what i was looking for, perfect! No nonsense straightforward stuff. Thanks. 👍

Got same problem, but screw got broken a bit inside. Nothing to grab the screw. Il try to drill wall plug and broke it. Thanks for video.

As much as I like the idea of bolt on outriggers, there is no way I'd be using rivnuts in the old chassis like that. I'd think welding in some crush tubes and long bolts through the chassis would be a better way of doing it.

Thanks OP, was expecting half a day of work having to take the whole front end of the car off to get to that thing out. So it’s a nice surprise to see how easy it is. Made my day!

When I had a Capri years ago, someone told me to soften the hoses with boiling water from the kettle. Been doing that ever since as there's less chance of a good hose being damaged.

That's a driver's side MOT fail technically.

Very nice job love the colour mate 👍 👌 👏

thank you for an interesting take on what must be a common repair, one which I found needing with my pre-*MOT. But my approach is a little more traditional than yours. I have bought lightly galv YRM double skinned footwell repair panels. they will be cut to what is removed with a lip and Mig welded in, some spot weld and some butt weld. This will be painted with Raptor U-Pol anti corrosive paint and finished with body paint, an some underbody paint or wax for the exposed paert. So the finished repair will be like factory.

That looks lovely, you did a great job ☺️

You should’ve put it inside out first to wrap the tie wrap, now the tie wrap is visible.

Thanks, and love your wee pal helper 👍

Thanks for the video it really helped ❤❤

Cheers,

What is the torque setting he used?

This car needs some rust treatment.

Don't you have to adjust the beam of the new foglight?

Fantastic video. Thank you!

I will be replacing mine next week. Watch to see how it goes!

Perfect… so simple and so necessary.. thanks for sharing mate

Yes thank you very clear and helpful - hope those aren't the wife's scissors 😂

Thanks for the informative and useful video of yours !

IV changed a bulb I know have condensation any tips what IV done ?

Hey mate. It's not clear where the blue cable goes. I have looked under the casing but just can't seem to find it. Cheers

same thing happened to me last night 😂 great video mate

lucky man, mine top mounts bolts won't move a bit :(

Do you have to switch off the hot water if you're taking the thermostat off and not removing the entire element?

Thank you for the tutorial, I couldn't find a way to adjust it.

you fucked that up and rivnuts will not pass an MOT

Good video, I plan on doing exactly this

I get it even when half the key was stuck in the lock cylinder about 15 years ago😀

I like videos like this, no nonsense talking and shit. Straight to the point! One question: any symptoms ? Noise ?

Thank you 😊 very helpful

Thanks for your videos and inspiration. The laid back approach makes a daunting task easier for us all 👍

Nice, done it all from inside the cab 💪

Great Job 👍

Thanks for that as mine didn’t even have them fitted lol, just now order two

Brilliant thank you. I had a similar problem and could work out how to take the lock barrel out of the old luck assembly

This video is interesting; however, it would be better if the camera was closer. Sometime ago, I had removed the lock rivets and replaced a small spring which was broken inside of it. So I've riveted again and it is working perfectly. It was not necessary to buy a brand new locker which is pretty expensive in Brazil.

That was an excellent video thank you

By sealing the ends of the weather strip with DumDum putty / butyl putty, you will reduce water ingress into the doors by a lot

This video was EXACTLY what I was looking for and the format and your clear instructions delivered!

When welding one day with full mask and suede jacket with the collar flipped up, i still had a welding spark jump into my mask and land in my eye. Terrible rust stain and burn scar. Had plenty of mri's since and no known particles still in there i guess.

Thanks, very clear and sorted my problem. I dropped mine from 8ft and the switch broke. You will need to solder one connection, worth considering if you need to get hold of a soldering iron as the switch is expensive.

The trickiest part is disconnecting the wire plug, but it does not show in the video.

Thank you! Great information for us guys with Defenders in the States!

I had a problem with tarnished contacts in the battery screwdriver. I moved the battery out a bit and the screwdriver worked. So it's not always the fault of the electronics!!!