Sig sauer quality control is trash. 3rd spectre comp and I still don't have a functional gun.

How would you compare the recoil of this setup to something like Glock 19 ?

I have the 4" 10mm & it also jammed. It got sent to S&W for what seems to be the standard polish job that doesn't fix the gun. Guess what? It still jams! Geez S&W!!!

When you hastily put your rival back together like it’s a Glock 😂 thanks bro not all hero’s wear capes 🦸

I have the none threaded berrel version of this gun. This is a great chest holster out in bear country gun. But what would be the purpose for a threaded berrel out in the woods.

I absolutely love mine. I built my ar with a Geissele lower with a mystic black that shoots the 7.62x39 rounds. I shoot steel case ammo thru it and have not had one issue or jamming.

Sounds like a personal problem

This is probably gonna be my next everyday carry

Imagine people complaining and not bieng able to manage 9mm recoil 😂

I carry mine in a miami style sholder holster. Woprks well and conformable.

Have you considered S&B is range ammo that is loaded barely hotter than 40 SW when you are crowning the FN "recoil king"?

Thanks ! Good video

I can stack rounds. But they’re always low and left. I can’t seem to take out gun movement for my trigger pull. Recoil management is not my issue.

Where does Smith and Wesson ever say the equalizer is targeting novice gun owners?

I fell asleep while listening to this. :) thank you.

I bought a 5.5. Redhawk have not shot It yet 🎉

Try double slapping the mag in HARD. That should be standard w any mag going in. Military training. Also pop the loaded mags bottom on your hand firmly before insertion a couple times on the bottom to properly seat/ line up the bullets in the mag. Works w my TH10. However, getting that mag release to loosen up took some work. Lil oil helped a LOT! 😁

If all you have is a 9 mm, carry the right ammo. If you can handle something with a little more pep, you should consider at least 10 mm with the correct ammo. Most people can handle 10 mm with a little bit of training.

The bdl is that S&W sold everyone junk and should replace the springs

Just my own opinion but I would say 99.9% these discharges are from static electricity I had a 45 ACP in the holster trigger guard go off when I pick some thing up and felt the static electrical zap boom the gun went off you could look in the shell which was not ejected because it was in a holster the shells from the firing range had a slight soot mark inside the one that fired in the gun did not strange it was different from every other shell like the powder fired then the primer primer had a very small dent it’s static electricity people!!!!!

I run an aftermarket barrel in all my Glocks not for a velocity increase but for a fully supported chamber, my 10’s are loaded hot so that helps

Need one of those😊

Does Springfield Armory make any conversion barrels for this, such as 357 sig?

Top 5 only micro 9s...

Sub-compact!!!!

That Glock has an aftermarket barrel. Did the other pistols have stock or aftermarket barrels? My G20 gen 3 occasionally gets a FF with Underwood coated 220gn hardcast. That 230gn DoubleTap your using seems to have an even flatter bullet than the Underwood. I might buy a box of that DoubleTap 230gn and run it through my stock barrel. I would expect one of those flat nosed bullets to get stuck on the feed ramp.

The hellcat to me is wildly uncomfortable but i do carry a shadow systems and agree with the 365

So beautiful 😍😍😍😍

In Alaska, they tested the S&M PERFORMANCE CENTER 10MM AT -27 degrees. First bullet jammed. But he noticed he has his finger on the slide. Slowing it down. After using proper holding, it fired several types of 10mm with no problems. Even the Bear round and the low grain one used for targets.

All those smaller guns are obviously compromised in some way, if you can carry a larger gun you probably should.

Grizzly Ammo 220gr the best in Alaska followed by Underwood

The KKM fully supports the round the Glock barrel does NOT --- a weak cased "HOT" round could rupture and blow the gun up --- why Glock recommends only using factory ammo and NO reloads???????? Is the best reason I know of to change the barrel.

So the grip screw ? What's up with that ?

Try G9 10mm ammo.

That CSX🔥

XDM all day everyday and twice on Sunday!

Showing the trigger off would look better if you turn the pistol around.

You are clueless, I own 2, 38/357 and a 9mm. But you are a topperware kind of guy.

Could you imagine if they switched the barrel with the recoil spring, like the Laugo Alien but without the gasblowback delay system !!!

From my research there isn’t much difference between the 3.8 and 4.5 ballistically. So I’m purchasing the 3.8 this afternoon. I’m curious if the 4.5 threaded barrel would work on the 3.8. Would be 5.25 overall and that would make a significant improvement. I know you can slide swap, but what about just the barrel. Yes it would stick out funny, but in the woods who cares.

I love my hellcat and my hellcat pro. I own a lot of handguns, rifles, and shotguns. When it comes to my EDC, it is usually my hellcat or my hellcat pro. Sometimes I carry a glock 43x. I own smith and wesson's, beretta's, kimber's, etc., but my hellcats are what I usually carry, depending on what I'm wearing and where I'm going. I shoot both the hellcat and hellcat pro extremely well. I love the sights, the capacity, the ergonomics, the ease in concealment, etc. If you can't handle the hellcat, then you need more practice at the range, and need to adjust accordingly. I have hundreds of rounds through both the hellcat and hellcat pro, and neither have had a single jam or malfunction.

l shoot 7000 rounds for one month my Mc9 Canik with out malfunctions. and no cleaning

I just watched this vid for the 2nd time and I would recommend some CCI #9 shot shells for MOSQUITO CONTROL!

This legion converted me. Was a glock guy my whole life. Best Duty Pistol hands down

Sig P938 says Hi.

So simple. Yet , I Couldn’t figure it out. Thanks.

Song makes me feel like im otp on hold🤧🤧

No Glock?

Can you remove the muzzle break and install the suppressor? I took out the three screws, but unable to remove the handguard... how do you remove the handguard?

How is it one year later?