also i love the lil mini tractors ones everywhere lol
@ziplocBagofRobloxia14 күн бұрын
would love to see a harware and electronics kit for this on your site, is it compatible with the mk3? (im printing one as i speak :P
@MakitProjects14 күн бұрын
@@ziplocBagofRobloxia Sorry, electronics are not the same on xl and normal. XL uses linear actuators instead of micro servos for rear arms and uses bigger motors and a more capable ESC.
@ziplocBagofRobloxia13 күн бұрын
@MakitProjects alright thanks, perhaps a regular non tipping unpowered wagon in the future?
@SB-10020 күн бұрын
What filament would you recommand for the tires? I am not shure wich TPU i should use. Thanks
@MakitProjects20 күн бұрын
@@SB-100 difficult to say. It depends on the printer you use among other things. In my case, with a prusa mk3s, sakata x-920 works really well. It's not very flexible, more like hard rubber but it prints very easy and with no clogs or any other problems. Don't know if it sells worldwide though. Hope that helps!
@Ciudadano31429 күн бұрын
increible diseño Compadre!!!!!!!!
@MakitProjects29 күн бұрын
@@Ciudadano314 gracias!
@terrydennis467Ай бұрын
Very impressive design. I have just accumulated all the parts for the smaller Mk3 though.
@SB-100Ай бұрын
Nice tractor. Do i need a bigger printer or is standart 21x21cm enough?
@terrydennis467Ай бұрын
There are three front half pieces over 24cm, max 24.3cm, rear wheels 20.7cm diameter
@MakitProjectsАй бұрын
@@SB-100 you'll need at least 25x21cm build volume and 20cm on Z
@SB-10029 күн бұрын
@@MakitProjects so a bambu a1 should do the Job?
@SB-10029 күн бұрын
@@MakitProjects and where can i find the Cultivator?
@MakitProjects29 күн бұрын
@@SB-100 yes of course, I printed it using an Bambu a1 and a Prusa mk3s
@Speedycat3 ай бұрын
Just finished assembling mine, it is awesome! Thank's a lot for uploading your designs
@MakitProjects3 ай бұрын
@@Speedycat thanks!! Really happy that you like it!
@wowwatcher1013 ай бұрын
When will there be a full parts kit??
@MakitProjects3 ай бұрын
@@wowwatcher101 Sorry but there are no plans for selling a full kit.
@wowwatcher1013 ай бұрын
@@MakitProjects dang the part list is quite daunting I just finished printing everything but
@MakitProjects3 ай бұрын
@@wowwatcher101 there is 3rd party hardware kit on the BOM, have you checked it? Sorry I edit myself, MK2.4 kit is not available , only mk3
@wowwatcher1013 ай бұрын
@@MakitProjects right :(
@RCmodeleng4 ай бұрын
Well done for work, determination and attention to detail, the important part, looks great, added to my list of things to make.. Keep up the good work and good progress with future projects and development.. Its not easy, but most appreciated 👍
@MakitProjects4 ай бұрын
Really appreciate these nice comments, that makes it worthwhile!
@newbenben36514 ай бұрын
bonjour merci pour tout c'est superbe video tuto . je voudrait savoir ou avez vous les boite de rengement pour les vis est boulon
@MakitProjects4 ай бұрын
I designed my assortment boxes to fit my needs but they are quite similar to other designs online. If you want, I can upload them.
@gopinath41196 ай бұрын
Thanks for the model. Everything is good except few parts availability. Would like to know it the 1:14 differential works as well?
@MakitProjects6 ай бұрын
Thanks! I've just added more links to buy the differential: docs.google.com/spreadsheets/d/1zS39qBsAIDUCei11DcebSgQcGvX-5azmxUevi4KTiyc/edit?gid=1714058316#gid=1714058316 Let me know if you have problems with more parts and I'll try to find more links.
@gopinath41196 ай бұрын
@@MakitProjects Hi thanks for the replay. Problem is, we cant import from China as it was Banned in my country. Here in my country I was able to get 1: 14 RC car differential instead of 1: 12. So I was woundering if 1: 14 differential can be compatable instead of 1: 12. If so I can order them.
@gopinath41196 ай бұрын
Wltoys XK 144001 Metal Differential is only avaliable for sale in my country.
@MakitProjects6 ай бұрын
@@gopinath4119 sorry, I haven't tried that one. It seems that axles are different so it shouldn't fit without modifications. The one I used is a replacement for FY01. Have you searched FY01 differential to see if you find any?
@gopinath41196 ай бұрын
@@MakitProjects Yes, its not available here but I will see if any of my friends coming from US. Will get from them. Would like to finish this project at any cost 😀
@thomasweis20776 ай бұрын
Hallo, ich bin begeistert von deinem Traktor, ich werde in den nächsten Monaten mit Sicherheit den ersten Traktor Drucker und zusammenbauen. Meiner Enkeltochter werde ich auch einen bauen. Ich freue mich schon auf ein weiteres Video. Liebe Grüße Thomas
@MakitProjects6 ай бұрын
Happy to hear that! I'm sure your granddaughter will love it!
@AakaarLab7 ай бұрын
I love your work sir
@MakitProjects7 ай бұрын
Thanks!!
@Ciudadano3147 ай бұрын
buenissimo !!! gracias por compartir estas cosas !!!
@MakitProjects7 ай бұрын
De nada!! Gracias a ti por ver mis videos!
@stephanevaucelles63787 ай бұрын
hello , thank for video
@MakitProjects7 ай бұрын
You're welcome!
@Hunihunor909 ай бұрын
27th and 28th step... what is that part under the front wheel turning rod that connects to the middle? Seems quite important but could not fins it in this manual or in the stl files :(
@Hunihunor909 ай бұрын
found it, but I still think it missing from video ;) great project though and thanks for the help in the beggining.
@haraldbartholome93889 ай бұрын
Hello, I have a question about the video, what is the name of the part that is plugged between the Y-cable and the servo MG90S.
@MakitProjects9 ай бұрын
Servo inverter, but I have been having problems with last versions of these inverters. If you use the radio I recommend Rc6gs, you can use channel mix and don't use any inverter nor y-cable.
@tscreationkakhandaki569711 ай бұрын
🔥🙌👌👌👌👌
@BaumiMike Жыл бұрын
Hello, I work in the field of agricultural technology and am a mechanical engineering detail designer. I always have the idea of constructing a Steyr 80 in an RC model, but so far this has failed due to lack of time. I have great respect for your model and will print it for colleagues as a Christmas present and give it away with the necessary components. Congratulations and recognition for the model and the assembly instructions! BRAVO
@MakitProjects Жыл бұрын
Thank you very much!
@MakitProjects Жыл бұрын
I hope your colleagues like it!
@ondrasekaxman7116 Жыл бұрын
Heslo Can I ask to you About dumper trailer step 4 on the threaded rod and on the rod is the šňůře and on the square is thet circle Sorry for the bad english I dost speak english
@ondrasekaxman7116 Жыл бұрын
😃
@tjitsewenselaar5874 Жыл бұрын
Nice thing man u olso have plans to make a tipper trailer ?
@MakitProjects Жыл бұрын
Yes, I plan to, but I need time ;)
@lorenzoberhofer5783 Жыл бұрын
Great my weekend is saved. Thx very much😊
@MakitProjects Жыл бұрын
Happy to hear that!
@GamerTechAj Жыл бұрын
Very nice bro
@ripmax333 Жыл бұрын
How much infill and Perimeters did you use on the TPU tyres? And what Infill did you use? Gyroid for example.
@MakitProjects7 ай бұрын
Sorry, didn't see your message before. It depends on the TPU brand. I normally use about 5-10% infill and rectilinear pattern. But I remember with my first TPU I could print with 0% infill and still get good top layers. That was great but sadly the brand does not exist anymore. I know this won't help a lot after all this time... Sorry again for missing your message.
@tjitsewenselaar5874 Жыл бұрын
When new video
@MakitProjects Жыл бұрын
Pretty busy at work but I'll try to do my best!
@tjitsewenselaar5874 Жыл бұрын
When u gona make some more tools for the mk3 tractor
@MakitProjects Жыл бұрын
I have the platform trailer ready. And I'll keep working on more tools. What do you suggest?
@tjitsewenselaar5874 Жыл бұрын
@@MakitProjects a ground bucket for the rear end a mower
@MakitProjects Жыл бұрын
@@tjitsewenselaar5874 any examples (pictures) of them?
@tjitsewenselaar5874 Жыл бұрын
@@MakitProjects where can i send them?
@MakitProjects Жыл бұрын
@@tjitsewenselaar5874 makitprojects@gmail.com
@ondrasekaxman7116 Жыл бұрын
Can dumper trailer be attached to openrc tractor mk3? If so, would you please make a build with me dumper trailer?
@MakitProjects Жыл бұрын
Yes it can. Yo have to use the optional rear hitch for the mk3. About the dumper trailer, I would like to improve it and use a linear actuator. So it makes sense to wait and make a video about the new version. But if you don't want to wait, you should be able to assemble it with the picture instructions. It's not very difficult
@ondrasekaxman7116 Жыл бұрын
Thanks
@nigelsimkin5910 Жыл бұрын
what percentage of infill did you use?
@MakitProjects Жыл бұрын
I normally use prusa slicer default values. Between 15-20% infill except for the TPU tyres with about 5-10%.
@ivangarbellini8876 Жыл бұрын
First of all, thank you very much for making such a great project free and public. I have a question about the drive motors, what are they? do you have a link to it?
@MakitProjects Жыл бұрын
Thank you! It's in the description in the BOM spreadsheet.
@DanielLauth2 жыл бұрын
Hello, 3d parts 7 is not in the assembly video. The 2 servos that are used at the rear, what are the servos? Thank you very much for the great work
@MakitProjects2 жыл бұрын
part 7 is in step 27, sorry for that! Rear arm servos are normal micro servos. Hope that helps!
@tjitsewenselaar58742 жыл бұрын
Can u make a video of how u progam the controler channel 3 and 4 for the rear servos
@MakitProjects2 жыл бұрын
I will try to make time and include it in the build with me videos.
@manuelg.17202 жыл бұрын
Muy buen complemento!! Olé!
@MakitProjects2 жыл бұрын
Muchas gracias!!
@nicolascarof7272 жыл бұрын
amazing work with the TEA20 !
@Fr1ndal2 жыл бұрын
Thanks for your work 👍🏻👍🏻👍🏻
@tjitsewenselaar58742 жыл бұрын
How u did u do the 2 smal servo on the reciiver
@MakitProjects2 жыл бұрын
You need to use mix function on your transmitter and connect to channels 3 and 4
@tjitsewenselaar58742 жыл бұрын
Do u make more inplements for this tractor?
@MakitProjects2 жыл бұрын
Most of previous tools are compatible and I plan on updating some of them and design new ones.
@tjitsewenselaar58742 жыл бұрын
For the 2 lift servos do i need a wire from 2 to 1 or?
@MakitProjects2 жыл бұрын
We've had some problems with 2to1 cable and servo reversers. For this project I use a radio with mix function and connect rear servos to channel 3 and 4, so I don't use that cable nor a servo reverser.
@tjitsewenselaar58742 жыл бұрын
Iam printing it now cant wait when its done
@tjitsewenselaar58742 жыл бұрын
When why get a drive video and whats the size i mean like 10 cm long or 20 cm long and how wide is it?
@MakitProjects2 жыл бұрын
It's about 29cm long 18cm wide. First video in action will be released very soon!!
@tjitsewenselaar58742 жыл бұрын
Is this the same size as the mk1 open rc tractor and whats the scalen 1/10 or 1/14?
@MakitProjects2 жыл бұрын
It is 1/9.5 scale (almost 1/10) but it's quite smaller than mk1 because it was smaller in real size too.
@tjitsewenselaar58742 жыл бұрын
@@MakitProjects ooh nice do u have a part list for my
@MakitProjects2 жыл бұрын
@@tjitsewenselaar5874 check video description and you'll find a BOM spreadsheet with parts and materials
@nanthakumar80422 жыл бұрын
we want printed assembly video
@MakitProjects2 жыл бұрын
I plan on doing it but it takes time... I'll do my best to have it sooner or later
@nanthakumar80422 жыл бұрын
After 1 year of R&D..humbot released new video
@MatthiasStreetview2 жыл бұрын
Great Design. When will the files be published? I cant wait to print it 🙂
@MakitProjects2 жыл бұрын
Thanks! They already are! www.myminifactory.com/object/3d-print-openrc-tractor-mk3-tea20-256143
@attackhelicopter6552 жыл бұрын
Have you considered making a front loader?
@jamietaylor53832 жыл бұрын
where to buy the differential and motor please
@rkcreatortoy2 жыл бұрын
hello, is sharing as a video copyrighted? via KZbin KZbin RC kids
@mafs412 жыл бұрын
What a great design and video, thanks.
@Hillbillyboy89RC2 жыл бұрын
Fantastic 🤩
@gordonbailey99843 жыл бұрын
Hi , do you have any other possible solutions for a drs that doesn’t involve a servo motor, if not no worries thanks
@MakitProjects3 жыл бұрын
Sorry, it has to have some kind of motor or servo.
@gordonbailey99843 жыл бұрын
@@MakitProjects yea i was thinking a motor with limit switches so i could make it driver activated
@MakitProjects3 жыл бұрын
@@gordonbailey9984 I only have servomotor option but yeah, you could try another approach ;)
@gordonbailey99843 жыл бұрын
@@MakitProjects no worries, ye i will try with limit switches and let you know how i get on 👍 thanks
@ashborn52413 жыл бұрын
What remote control did you use for the drs? If i use say a 6 channel radio remote can i control the drs, the steering and the rear throttle independently?
@MakitProjects3 жыл бұрын
Yes, 6 channels means you can control 6 different things.