I especially liked your design of the tip of your dril pipe using galvanized steel pipe.
@ssarraf6855Күн бұрын
Man, l absolutely love ❤️ your attitude! And your persistence and perseverance, not to mention your family who stood by you 🎉❤
@jamesbailey77853 күн бұрын
Just for info; sometime near 2019 Bobcat changed the "problematic" check ball pick up tube design and switched to a "primer bulb with Check ball in "it. I would just switch all primer bulbs :)))
@new4friends8 күн бұрын
Was the coupling you broke a well drive coupling or a regular one?
@worldsstongeststrains9838 күн бұрын
You know they make a 4 foot extension for gas augers right? Turns 4’ into 8’ or 12’
@craigmonteforte611110 күн бұрын
Dude I’m not going to Monday Morning Quaterback a thing IMO this entire Process was pretty Impressive , no matter what you attacked itvAggressively and came up with a possible Solution Yet Continuecto give it the Hard Work until Success
@thomaspaccione721412 күн бұрын
This has to be the best oil change video I have even seen.
@Fix-p7z13 күн бұрын
Hi bloke found this water drilling method so you don't need to backfill Cheers 🥂🥂🥂 kzbin.info/www/bejne/aaGyhK14nKdrjbcsi=7gR5g6LGhEHSAWZl
@richardamick169019 күн бұрын
There goes his back
@CrazyFamRust24 күн бұрын
Did anyone notice that you could just keep holding the power on the auger and it would come up while you pull. Like drill , stop drilling and big gets stuck so start drilling again and pull out.
@bruceglisson172017 сағат бұрын
I have drill a many a hols with my auger and never have gotten it completely stuck like he did
@brianstouffer330624 күн бұрын
I WAS WONDERING HOW YOU ARE LIKING THIS MULCHER NOW THAT SOME MORE TIME HAS GONE BY. ANY ISSUES? HAVE YOU HAD TO REPLACE ANY TEETH? HOW MANY HOURS DO THE TEETH LAST AND ARE THEY EXPENSIVE TO REPLACE?
@SteveDoesEverything15 күн бұрын
Still love the mulcher. I don’t have any regrets buying this. I have had to replace the teeth. You can turn them to get more life out of them. Each replacement tooth is $27 plus tax. As far as length of time the teeth last, that completely dependent on many factors, how often you cut into grade, what type of material your cutting etc. you should examine the teeth after every use and determine how efficiently you’re cutting.
@Boeing_hitsquad25 күн бұрын
Yes, deep breaths
@olgaguer644325 күн бұрын
5:10 - drilling teeth
@olgaguer644325 күн бұрын
Pipe supply store
@Perfectjzman29 күн бұрын
Super cool dude, shocked pvc held up to the torquing from drilling
@sltpsvita1129 күн бұрын
Did anyone get this to work?
@andreloudon8934Ай бұрын
You need to circulate a clay/water mix going into the inside of the pipe and returning around the outside of the pipe using a 2 inch or better trash pump in order to stop the ground from collapsing around the pipe and freezing it in place. Dig a big hole next to the well (mud pit) and fill with the slurry and circulate it while drilling.
@john1072Ай бұрын
Hello, i have questions/concerns about isoscell. Are they legit and on the level? They responded to me via text message and now they want money sent through paypal - seems like a scam. Please advise - thanks
@johnmorris1637Ай бұрын
Should of used galvanized steel pipe when drilling
@HasanAktuğ-q4xАй бұрын
HELAL OLSUN.Çok güzel iş.
@jasonpaschich538Ай бұрын
You got er done so good job. FYI, water volume is more important than water pressure. Two hoses sealed off so the water and sand/dirt/cuttings have to come up out of the hole not back up the pipe. And go sloowwwww. Let all that dirt/sand come out up away and you wont get stuck.
@tophatpumaАй бұрын
Sadly my soil is mostly rock..
@Dan-e5fАй бұрын
You need an office job.
@JT-qf4itАй бұрын
How does it do on palmettos?
@SteveDoesEverything15 күн бұрын
When the teeth are good. It powers through them pretty decently
@desfiguradoalnacerАй бұрын
I have a question, my don't leak but the boom won't stay up will.slowly come down making a cracking sound same bobcat 763 any help would be appreciated
@seekingadventuresАй бұрын
Use your legs, not your back to lift.
@commentseditedАй бұрын
Using bentonite?
@davidvance7339Ай бұрын
You are going to injury your back bending over and pulling upward that way. Use your legs more.
@sport07-o2lАй бұрын
You hurt my back yankin on that auger
@stevee4942Ай бұрын
Keep the auger clear, never got my auger jammed.
@dwaynet21842 ай бұрын
You would go faster without the pressure washer, you need more volume of water to move the dirt faster. Pressure washers are designed to do a lot of work with little water as possible and you need all the water you can get .
@vincew.69052 ай бұрын
Once to break in . Is done it’s OK to use 50:1 on this unit.
@Yankee_Redneck66982 ай бұрын
Husband:😰 yank, pull, jerk, jerk, pull, think, yank, pull, pull, think, yank, pull, jerk, sigh to self...😮💨 Wife:🫤 "Is it stuck? Husband: *Quietly considers a murder for a second* 🤨🤐
@RodgerHopkins-w5h2 ай бұрын
Got the auger hooked on a rock!
@UltraLimitedHD2 ай бұрын
Definately the armstrong method. In Florida we can usualy zio them in.
@jws39252 ай бұрын
This might work in sandy soil with no rocks but does not work for most people. So if you think it is just this easy make sure you have the right type of soil.
@gianbattista2 ай бұрын
ma non farci ridere
@michaelfoort25922 ай бұрын
Sharpen your bit with a grinder, your metal loses its temper and dulls super quick.
@michaelfoort25922 ай бұрын
Fix it again Tony
@nihataltinboga75442 ай бұрын
Hello friend, I did as you said and the scraping starts in hiveos, but when I log in with the user and password in 51pool, the account does not open.
@radjeshsingh2 ай бұрын
And can you drink this water ? Is it deibkable ?
@ChromeDaimao3 ай бұрын
how did u get the second cropping part? Mine just stays static across the video.
@moviesforrandy3 ай бұрын
I am to dam old for this.
@Clayton-Bigsby9663 ай бұрын
The cutoff wheel at eye level😂
@jdere317603 ай бұрын
Did you soldered or brazed those refrigerant lines? Solder will never hold the refrigerant pressure on the hottest day! If you know anything about spraying, it’s 2000° of heat. Kind of dangerous up there in the attic with all that wood and insulation. Maybe you should show how to spray down and wet surfaces that are flammable? I don’t know. Maybe the difference between experience and non-experience? Lots of attorneys out there waiting to pounce on content that ends up killing someone or burning down their house.
@serenityplantation76383 ай бұрын
The beginning of this video is proof that KZbin should be banned unless ur licensed to teach 😂😂😂. Anybody can show you how not to do shit with ur rental equipment
@barbrice7213 ай бұрын
Pita. Just named my Black cat that. Lol
@Nonyabusiness9113 ай бұрын
Oddly enough water jetting without predrilling a hole works better. If you pay attention to the videos created by the guy that started all this he’ll tells you. Use the well size you want and jet it down. I had coral about 2’ thick I had to get though. I made a drill bit using conduit. I cut a large bit in half wielding a section to each end. I used an impact hammer and after a couple of hours got through. If I ever do it again I will use galvanized well pipe and special couples and a jack hammer. The pros here use a sled with a hundred pounds to slam them down. I believe a jack hammer with a home built attachment would do it. I did 27’ before jetting stopped working. I ran 2 hoses and all the water just disappeared. It was 2013 and it has never run dry even after a massive drought.
@ggsholdings72254 ай бұрын
Thanks for the detailed explanation
@DanTheManIOM4 ай бұрын
and Steve kept the neighbors entertained for hours and hours and slept so soundly at night, no one could wake him !
@JonathanJanaszak-ir2rv4 ай бұрын
Oh, I didn't see you have the gasket on the twist n seal flange and also a big no no, NEVER EVER caulk the base of a toilet unless the subfloor is concrete, otherwise when the wax seal goes you will trap the water underneath and rot out the plywood subfloor.