Was that a McLaren towards the end that let you by?
@performance_engineering15 күн бұрын
The black car was a lotus exige, there was red 600lt in the middle of the vlog aswell
@richardalvarez100329 күн бұрын
what size tires you were running . Im scared to rub on 275/35zr20
@performance_engineering29 күн бұрын
From memory it was running the same tyre size and didn't have any rubbing
@968Porsche1993Ай бұрын
3rd season in a row I've watched this video before doing my end-of-season service Thanks again!
@performance_engineeringАй бұрын
@@968Porsche1993 that's brilliant, good to know it's helpful 👍👍
@968Porsche1993Ай бұрын
@@performance_engineering Went great! What is the average time to complete this service? I spent 3 hours yesterday and another 3 hours today? Didn't include a trip to the Tire shop to get a screw removed and a tire plug after finding a sheetrock screw in my rear tire!
@968Porsche1993Ай бұрын
ps DON"T FORGET TO RELEASE THE PRESSURE FROM YOUR BLEEDER BEFORE UNSCREWING IT FROM THE RESERVOIR!
@performance_engineeringАй бұрын
@@968Porsche1993happy days your all went smoothly. Hmm probably around 3 to 4 hours, depending on how familiar you are with removing the centre locks.
@968Porsche1993Ай бұрын
@@performance_engineering pps I hate brake dust!! As long as the wheels were off, I deep-cleaned them inside and out. It took 3 scrubbing to get them clean and added a few hours to the job
@leslieankers1886Ай бұрын
Mint where are you based
@performance_engineeringАй бұрын
@@leslieankers1886 based in Cardiff, CF24 5FF 👍
@White_Chapel2 ай бұрын
My 2.0 caddy maxi could do with a remap like this. Was it done on standard factory hardware or did that need upgrading too?
@performance_engineering2 ай бұрын
This was done on a completely standard car, no hardware modification. Send me a email if your interested on getting it tuned
@White_Chapel2 ай бұрын
@@performance_engineering Nice one . Thanks
@kush2522 ай бұрын
How much does it consume fuel at 140 km/h, ?? thank you
@performance_engineering2 ай бұрын
MPG is very subjective and haven't tested at them speed I'm afraid but you should see an improvement in mpg when driven economically
@stance4life.982 ай бұрын
Sounds lovely
@performance_engineering2 ай бұрын
Was a great sounding system 👌
@teddiazjr.62233 ай бұрын
Another great video Please post the link for the spring compressor
@performance_engineering2 ай бұрын
@@teddiazjr.6223 glad you enjoyed it. Try this link, good quality springs compressors that don't cost too much - www.sealey.co.uk/product/5637175238/1000kg-2pc-coil-spring-compressor
@Nachtwind73 ай бұрын
Did this just today to replace a faulty coil. Good video, thanks!
@performance_engineering3 ай бұрын
@@Nachtwind7 brilliant, glad it helped 👍
@steinyndestad4 ай бұрын
Very good. Best instruction video on center lock removal online. You may want to post that part as a separate video. 👍
@performance_engineering4 ай бұрын
Glad it helped. That's actually a good idea, ill look into uploading just the centre locking part of the video separately. Thanks
@cicliolmo71526 ай бұрын
those springs and spacers really gives it that nice fitment and stance. Top work mate !
@performance_engineering6 ай бұрын
Yea it does look great 👌 cheers mate 👍
@Abelsgarage_6 ай бұрын
Would this process work on a B9 SQ5 ???
@performance_engineering6 ай бұрын
Process will be very similar for the a SQ5 👍
@Tangored57 ай бұрын
I'm debating whether I should get the 034 springs or H&R Springs. Which one would you recommend?
@performance_engineering7 ай бұрын
I use H&R on near every vehicle which comes in for lowering springs. 034 will probably give you the same stance but not sure on the ride quality
@chistianmeyer27287 ай бұрын
how much are those soul headers
@performance_engineeringАй бұрын
If you send me a email I can get you some prices
@allym95007 ай бұрын
I’ve got one of these 102hp 2.0l euro 6 jobs. Now I’ll need to map it up having seen this 👍🫡
@performance_engineering7 ай бұрын
Makes such a difference, you will love it
@cicliolmo71528 ай бұрын
Top work mate. Do you recall if these were Sport or SuperSport springs ?
@performance_engineering7 ай бұрын
Hi, believe these are the supersports seats on this S5
@b28hizzle8 ай бұрын
How can i get a legal version of this!
@performance_engineering8 ай бұрын
Can offer soul performance sports cat downpipes. Send me an email if you are interested - [email protected]
@johnkim93348 ай бұрын
Wht brand splitter do you have on the front bumper?
@performance_engineering8 ай бұрын
Hi. Not 100% sure but think this was Maxton splitter
@eternal2k49 ай бұрын
How did you remove the orange from your headlights?
@performance_engineering7 ай бұрын
This is how they come from the factory in the UK
@WanderingFriar9 ай бұрын
Lovely result but will never do it to mine. I’m too chicken. Great job, Nate. Love your presentation style.
@performance_engineering9 ай бұрын
Thanks, glad you enjoyed the vlog. 👍 Lol the 991 does look great even in stock form so don't blame you for leaving it alone lol 😁
@TheCinderellaman109 ай бұрын
That torque line is real power, many other setups will lose torque along the rev range, but with your mapping that is a proper fast road car, lovely.
@performance_engineering9 ай бұрын
Yea this was a pretty quick S3 on the road, was very reliable too at this performance level. Glad you enjoyed the vlog 👍
@R1Custom9 ай бұрын
You mentioned you added spacers, can you recommend them/ or a brand that fits a 2018 Audi A5. Thanks
@performance_engineering9 ай бұрын
Hi. Yes that's not a problem, i supply Bimecc spacer kits on the online shop if your interested in purchasing a set. Www.performance-engineeringltd.co.uk
@hlwilliams059 ай бұрын
Do you have torque spec for the different bolts? Bought a set of springs for my car and I’m looking to do it soon, but don’t want anything to come loose
@performance_engineering9 ай бұрын
I don't I'm afraid sorry. All the bolts are very hefty bolts so you will be fine tightening them up as tight as you can.
@DanDada9 ай бұрын
nice video! just don’t wear jewelry during operations please :)
@performance_engineering9 ай бұрын
Thanks. Can I ask why you mentioned about not wearing jewellery while working
@DanDada9 ай бұрын
every dealership doesn’t allow wearing watches or any type of jewelry because it can a.) scratch the car b.) is a potential risk of injury for every mechanic
@filmnegah.9 ай бұрын
Voodo blue colour
@performance_engineering9 ай бұрын
😁👍
@tobymarshall25210 ай бұрын
Looking to get my m135i tuned do u do gearbox software aswell?
@performance_engineering10 ай бұрын
Hi. Yes I can tune the gearbox for you aswell as the ecu. If you wanted to send your details to [email protected] and I'll some info for you.
@omedonnie10 ай бұрын
Stock it is low enough, especially with PDCC.
@performance_engineering10 ай бұрын
To be honest, for most people it is most likely low enough, but I wanted to reduce the arch gap
@omedonnie10 ай бұрын
I understand you. But my Carrera 4 GTS sits stock at almost the same height as yours. I do have PDCC.@@performance_engineering
@performance_engineering10 ай бұрын
I didn't have PDCC on my GTS. If I remember correctly PDCC cars was a little lower.
@omedonnie10 ай бұрын
That's right 20mm. How much did you lower your red beauty?@@performance_engineering
@performance_engineering10 ай бұрын
The H&R lowered it around 25-30mm over a non PDCC GTS. Doesn't sound much but it looked brilliant and the ride was near enough the same as stock.
@nighthawk007711 ай бұрын
Brother just drive and enjoy the car. No one in Porsche land really cares all that much about 0-60
@performance_engineering11 ай бұрын
Cars long gone now mate
@Posyworlwide11 ай бұрын
I’m subscriber 880 , 8 is the number wealth. Let’s go 😅
@performance_engineering11 ай бұрын
Haha I like that 🙌🙌🙌🙌
@Posyworlwide Жыл бұрын
Mate you are good at this, such a natural on camera. I hope you comeback, you’ve earned yourself a follower.
@performance_engineering Жыл бұрын
Much appreciated your comment 👌 I do always think about getting back into the vlogging, I will get some new content very soon 👍😁
@Posyworlwide Жыл бұрын
@@performance_engineering Awesome hope to see you soon.
@Freshwilliams126 Жыл бұрын
That 911 sounds good. Damn
@performance_engineering Жыл бұрын
😁🙌
@rybatb3 Жыл бұрын
Welcome. Seats from what car?😅
@performance_engineering10 ай бұрын
Hi. Not sure but believe there from a VW Touran maybe
@owenjones63Ай бұрын
Scirroco R mounted on Touran Bases
@rybatb3 Жыл бұрын
Welcome. Seats from what car?😅
@performance_engineering Жыл бұрын
Not sure to be honest, possibly a Touran or Passat
@brianmcconnachie7400 Жыл бұрын
Just watched this video good work how much does the h ^r springs lower the car and what size of spacers thanks
@performance_engineering Жыл бұрын
Thanks 👍 they lower the car around 20-30mm and from memory I'm sure there is 12/15mm spacers in this. Hope this helps
@BIueDreamm Жыл бұрын
Can’t wait to get my hands on one of this GTS!
@performance_engineering Жыл бұрын
They ate great cars the GTS, sure you will love it
@thetruth52772 Жыл бұрын
Top video mate! Thinking of doing the same to my S5 too. Cheers for the upload
@performance_engineering Жыл бұрын
Glad you enjoyed it. This setup really does look great for the S5
@allenvaughn5410 Жыл бұрын
Are there any check engine lights or ecu issues with the catless downpipes?
@performance_engineering Жыл бұрын
Hi. Yes the EML will come on for cat efficiency when running the decats so would require them to be mapping out from the ecu.
@romqa5 Жыл бұрын
Which h&r are this ? Sport or super sport ?
@performance_engineering Жыл бұрын
From memory they was the sports H&R set
@financeunchained Жыл бұрын
So tempting to add this to my almost identical car!
@performance_engineering Жыл бұрын
You will live it, brings the car alive 👌
@financeunchained Жыл бұрын
@@performance_engineering did you ever dyno it afterward?
@performance_engineering Жыл бұрын
I didn't I'm afraid. I wanted to but had an offer to purchase the car and it went straight away. Was doing low 6s on a 100-200kmh which is around 991.2 Turbo S pace so went well
@financeunchained Жыл бұрын
@@performance_engineering wow!
@reminero1955 Жыл бұрын
Great video bro! Quick question, about how much wheel horsepower do you think you can tune out a 970 Porsche Panamera Turbo model? ( non S model)
@performance_engineering Жыл бұрын
Hi. Glad you enjoyed the video. WHP figure for yours I would expect to be around 550whp with stock being around 480whp. Hope this helps
@lexus0829 Жыл бұрын
nice i have a 2012 Turbo S already have 84k miles.. havent tuned it..thanks for the video.. i think the color is mexico blue..
@performance_engineering Жыл бұрын
Glad you enjoyed it. Ohh you will absolutely love your Turbo S even more when you tune it, great motors. Yes, I think your correct, Mexico Blue 👍👍
@meliodasD2 Жыл бұрын
I'm usually not the biggest Audi fan but it turned out really nice!
@performance_engineering Жыл бұрын
Yea I do agree, looks very smart once lowered 👌
@tkendrick1 Жыл бұрын
Recently used your video to do a install on my 2023 a5. Does this affect adaptive cruise control when getting a fresh alignment ??
@performance_engineering Жыл бұрын
No I don't believe it should effect your cruise control. Maybe run a diagnostic report to see what faults come up
@banterwithbawden5444 Жыл бұрын
Could you do this on an older caddy like 2005 ?
@performance_engineering Жыл бұрын
You can tune a 2005 Caddy but I don't go back any later than a 2009/10
@aja212x5 ай бұрын
Did my 2008 Caddy with a stage 1, added 35bhp and extra 70nm of torque, reasonable gains. Feels better, less dead spots.
@klasmvm4966 Жыл бұрын
Amazing video, this covers just how to do it with the least pain possible. One question though, will this work on a A4 without the factory lowering springs? Will it clear far enough when the springs are 25mm longer?
@performance_engineering Жыл бұрын
Thanks, hope it helps with your install. What I would recommend is, when you have to compress the spring, try and compress it slightly more to take up that extra 25mm then it should allow enough clearance
@othmane767 Жыл бұрын
what about fuel economy after the tuning is it better or worse?
@performance_engineering Жыл бұрын
Typically should see around 3-5mpg improvement when driven economically
@jackl517 Жыл бұрын
Top top bloke
@performance_engineering Жыл бұрын
👍😁
@ryanowens3658 Жыл бұрын
What kind of spring compressors are you using?
@performance_engineering Жыл бұрын
They are just normal spring compressor mate, can be bought from most motor factors or ebay, amazon