Пікірлер
@aqeelgill6039 16 сағат бұрын
Thank you so much its worked
@UltimateDIY 15 сағат бұрын
Welcome!
@vyktorsolo3468 16 сағат бұрын
God bless u man, u r the only man on earth who figured out to fix ACP STATE FAILEURE, It saved my nas, thx a lot once again
@UltimateDIY 15 сағат бұрын
Welcome!
@oana4295 16 сағат бұрын
Buna, In pachet e acel chenar mic alb, ca un inel care se introduce in robinet. E musai sa fie pus desi robinetul merge fixat si asa cum e el?
@UltimateDIY 16 сағат бұрын
Buna. In pachet sunt diferite sisteme de montare in functie de tipul robinetului de pe calorifer. Utilizati doar ce este necesar pentru a-l putea monta.
@oana4295 11 сағат бұрын
@ am inteles. Cumva nu reusesc sa il calibrez. Am setat temperatura de 21 de grade, dar nu porneste apa in calorifer. Porneste doar dupa ce dau ok si apar apare pe ecran 6900, ceea ce reprezinta 900 de secunde. Trebuie acele secunde lasate pana la capat sa se scurga?
@UltimateDIY 5 сағат бұрын
Esti pe ceva mod cu timer. Muta pe modul manual.
@oana4295 Сағат бұрын
@ da asa e, am reusit. Merge, insa pacat ca scoate un fluierat non stop…ceva ceva nu ii convine la pozitie. Desi am pus acel chenar alb ca altfel se misca fara el.
@UltimateDIY 51 минут бұрын
Fluieratul il face robinetul in sine, cand trece apa prin el si e semiinchis, nu termostatul.
@jgbelmont 17 сағат бұрын
How do you deal with the extra amperage into the UPC? It was not designed to take that many amps in yo.
@UltimateDIY 17 сағат бұрын
Amps don't work work like that. The UPS takes what it needs and that's it.
@mohamedaitcheikh4393 22 сағат бұрын
Bro it was fixed b ut I have A new issue it's when ever I want to turn on my laptop I have to do the same proccess everytime is there are any final solution for this ???
@UltimateDIY 20 сағат бұрын
Yes, replace the bios battery of the laptop, so the bios settings don't get loat at every shut down.
@jcbstarworld Күн бұрын
Thank you it worked ☺️
@UltimateDIY Күн бұрын
Welcome!
@prathamjitesh1641 Күн бұрын
Thank you it really helpful.
@UltimateDIY Күн бұрын
Welcome!
@vincentgunst1271 Күн бұрын
Thank you for the info, it helps.
@UltimateDIY Күн бұрын
Welcome!
@IWoVex Күн бұрын
2y later and still not sure if i should take the rubber/silicone pads off 😂
@UltimateDIY Күн бұрын
I don't either 😁
@IWoVex 17 сағат бұрын
@UltimateDIY You are amazing, still replying to comments on 2-3y old videos is something rare to happen on yt thank you for that ! , but may i ask if you are still using the same fryer till now if you are then this thing is a beast i bought it up recently so I can't tell how long will it function normally but you on the other hand used it long enough to review it's quality.
@UltimateDIY 17 сағат бұрын
Thank you! Still using it just fine. It looks a bit rougher now, but still working 🤭
@IWoVex 17 сағат бұрын
@@UltimateDIY Amazing 🤩 , thank you so much for the reply and i hope your unit keeps running fine for a long time and mine too !.
@UltimateDIY 17 сағат бұрын
@IWoVex welcome!
@normanseagull4027 Күн бұрын
Might be better if you try it out first then review.
@UltimateDIY Күн бұрын
Could be, but this is my "workflow". I also answer any question in the comments over the years, so that actually brings recent information all the time.
@UltimateDIY 2 күн бұрын
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬ THANK YOU FOR WATCHING! PLEASE LIKE AND SUBSCRIBE! ▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
@anushkasingh8458 2 күн бұрын
very detailed vedio
@UltimateDIY 2 күн бұрын
Thanks!
@novice0012 2 күн бұрын
What type of ram did you use here? DDR3 or DDR3L?
@UltimateDIY 2 күн бұрын
If I remember right it's DDR3L. As a reassurance, DDR3L modukes can work as DDR3, but not viceversa.
@fnsweatzy 2 күн бұрын
Doesn’t work
@UltimateDIY 2 күн бұрын
Not possible. I already reset 2 units by this exact procedure. Maybe you are doing something wrong.
@fnsweatzy Күн бұрын
@ I did this but it didn’t work so what I did was I went into settings and clicked power off as I clicked restart it worked
@UltimateDIY Күн бұрын
Weird. Maybe it was stuck somehow. But glad you managed to get it to work 👍🏻
@jesua_chvgar 2 күн бұрын
Straight to the point, and all working as it should. Thank you, my man.
@UltimateDIY 2 күн бұрын
Welcome!
@cristi.flo.47 2 күн бұрын
Merge aceasi metoda si pe desktop de la lenovo ?
@UltimateDIY 2 күн бұрын
Nu stiu asta din pacate
@torsen1987 2 күн бұрын
Why not just buy Milwaukee or Festool from the start? Why even bother with these cheap tools ?
@UltimateDIY 2 күн бұрын
Some kind of joke? Not a single one of these cheap tools has failed on me in a way that it could not be fixed. As an average home user there is absolutely no reason to buy tools 2 or 3 times the price. As a pro that makes money with them, yes, it makes sense to get something a bit lighter or more powerfull or even more reliable, as any downtime costs you money. But for home use? Hell no.
@hellsing56666 2 күн бұрын
Cause we are broke as fuck
@UltimateDIY 2 күн бұрын
@hellsing56666 😁😁✌🏻
@iliepetrescu819 2 күн бұрын
De la ce magazin ai cumparat membranele? Multumesc
@UltimateDIY 2 күн бұрын
Nu magazin. Claudiu Urban acum multi ani.
@TclsparePhone-b4s 2 күн бұрын
Is the odd adapter sata and usb3? What is the usb interface? Can it be adapted to fit a stick type ssd (msata/m.2 etc) alongside the 2.5" is the usb visible as a boot drive? If you could have a zif ssd, 2.5" ssd and msata ssd all in one that makes for a LOT of storage space.
@TclsparePhone-b4s 3 күн бұрын
Can you install an SSD in the wwan slot then boot with clover?
@quantummechanized2975 3 күн бұрын
can you do it with the laptop on so you can directly blow on the entire fan if you can only see part of it through "cracks"?
@UltimateDIY 3 күн бұрын
No, not a good idea.
@quantummechanized2975 2 күн бұрын
@@UltimateDIY how would i clean all of it without opening it and voiding warrenty then?
@UltimateDIY 2 күн бұрын
Tha fan spins when you blow air on it, so most of it will get cleaned, even if you can't see it all.
@quantummechanized2975 2 күн бұрын
@@UltimateDIY thanks
@putnamlandconservancy8941 3 күн бұрын
Thank you! Worked perfectly!
@UltimateDIY 3 күн бұрын
Welcome!
@Johns.wildlife 3 күн бұрын
Great video thx
@UltimateDIY 3 күн бұрын
Welcome!
@Brab82 3 күн бұрын
Frigging
@nguyenchihuy4915 3 күн бұрын
So so so much thank you ❤❤❤
@UltimateDIY 3 күн бұрын
Welcome!
@AvengeBasketball 3 күн бұрын
This unit is terrible. Doesn't let you get really hot water when you need it. Hot water lever get's stuck and unable to turn after 2 years of use.
@UltimateDIY 3 күн бұрын
What does really hot mean for you? Are you pressing the button to allow extra rotation for hotter water?
@AvengeBasketball 3 күн бұрын
@ Yes, I pressed the button so it can rotate forward for hotter water. But there’s a limitation for this unit. “The thermostatic mixer is pre-set to a safety stop temperature of 38 °C. Since operating conditions in each supply system varies, it might be necessary to calibrate the mixer according to the service and installation instructions.” You could probably overwrite before installing it but most don’t know how.
@UltimateDIY 3 күн бұрын
Nope, you got it wrong. This is the limit without pressing the button. With it pressed it goes way higher. But maybe you have a defective or decalibrated unit.
@naijachoicetv 3 күн бұрын
5 years later, you're still a life saver. A repair shop is charging heavily for this
@UltimateDIY 3 күн бұрын
Glad I can help 👍🏻
@gimenes29 4 күн бұрын
Audi A5 Coupe 2016!
@UltimateDIY 4 күн бұрын
Thank you!
@AdrianP07 4 күн бұрын
Aoleooooo ... asta-i englezeasca rumaneasa !!!! Va cunoaste lumea de la o posta breee !!!
@UltimateDIY 4 күн бұрын
Va? Dar tu nu esti roman? 😁
@technicalupsfaults5074 4 күн бұрын
How to change total forward energy Reading?
@UltimateDIY 4 күн бұрын
No idea
@foreverbellet3 4 күн бұрын
toppppp
@UltimateDIY 4 күн бұрын
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬ THANK YOU FOR WATCHING! PLEASE LIKE AND SUBSCRIBE! ▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
@RandomActivities_FM 4 күн бұрын
I clik Shift+f10 cant display cmd sir... Update : I solved this... In the firs step.. I force clik the power buttom to restart.. And then to the 2nd step to regedit and solved the problem... Thanks
@sharath7cool 4 күн бұрын
Thank you it works
@UltimateDIY 4 күн бұрын
Welcome!
@Runitback405 5 күн бұрын
you are a very funny guy 😅
@UltimateDIY 5 күн бұрын
Thank you!
@georgecristea7287 5 күн бұрын
salutare astazi mi-am cumparat acest ups intrebarea mea este: cum fac sa setez sa imi iasa 230 pentru centrala pe gaz exista vre-o setare?? prin pc ? prin care pot face aceste ajustari? si sa va spun de ce vreau aceste setari m-am trezit cu 251 de volti in priza din cauza celor de la compania de furnizare curent enel electrica cum s-or mai numi ei si vreau ca prin acest ups sa setez iesirea din el fix la 230 sa nu treca de aceste numere se poate prin calculator sa editez iesirea din el????
@UltimateDIY 5 күн бұрын
Salut. Din cate stiu eu nu se poate seta ce vrei tu. Pe langa asta la centrale cred ca trebuie ups cu unda sinusoidala pura, pe cand acest ups are unda sinusoidala simulata. Cel mai bine ar fi sa contactezi nJoy direct si sa ii intrebi.
@georgecristea7287 5 күн бұрын
@@UltimateDIY atunci nu stabilizeaza curentul sa inteleg acest tip de ups???? cat intra atata scoate??? ca pe manual nu zice ca e si stabilizator de tensiune
@UltimateDIY 5 күн бұрын
@georgecristea7287 stabilizeaza doar in afara unor limite care nu pot fi schimbate. Cand scade tensiunea sub limita si cand creste peste limita cupleaza el si intra pe baterie. Dar aceste limite nu se pot schimba si tensiunea pe care o scoate nu este fixa la 230V si poate creste spre 250V in functie de cat de consumata e bateria interna. Apropo, la o retea de 230V tensiunea poate varia intre 207V si 253V si inca este in limita acceptata de +-10%.
@georgecristea7287 5 күн бұрын
@@UltimateDIY atuncîa nu nu pot vedea ce setare are fîind stabilizată dîn fabrică șî asta imi poate dîstruge centrala nu?
@UltimateDIY 5 күн бұрын
@georgecristea7287 contacteaza nJoy pentru limitele exacte. Centrala se distruge daca ii depasesti limitele. Astea le poti afla din manualul centralei.
@nikdelta399 5 күн бұрын
Go directly to minute 6.00, before is nothing
@UltimateDIY 5 күн бұрын
I disagree. Many people like to see what's included in the box and the manual itself. People are not always directly interested in the test itself. So I include everything and everybody can choose what to watch.
@quiminiesta9969 5 күн бұрын
great video!!!!
@UltimateDIY 5 күн бұрын
Thank you!
@quiminiesta9969 5 күн бұрын
@@UltimateDIY I can buy an AAA 1800mha battery or it's too much?
@UltimateDIY 5 күн бұрын
AAA typically have maximum 1200mAh. If one is advertised at 1800mAh and it's not a well known brand, I doubt it actually has that capacity. But you can buy any capacity you want, it's not a limiting factor.
@quiminiesta9969 4 күн бұрын
@@UltimateDIY Thank you!!
@UltimateDIY 4 күн бұрын
Welcome 👍🏻
@DennY-k8e 5 күн бұрын
My chargers shows 2 LED diods (Red and Green) they are blinking. What's the problem? It worked all time in mashine
@UltimateDIY 5 күн бұрын
Maybe overheated battery, but don't remember for sure.
@DennY-k8e 5 күн бұрын
@UltimateDIY It's not , both indicators blinking at the same time. 2nd red indicator and last green indicator
@UltimateDIY 5 күн бұрын
Then try to reseat the battery. Could be bad contact.
@teddytembo2132 5 күн бұрын
Thanks so much exactly what am passing through with my laptop Toshiba let me try.
@UltimateDIY 5 күн бұрын
Welcome!
@lukaavbersek2643 5 күн бұрын
Thank you for posting this and save a lot of time for me👍💪
@UltimateDIY 5 күн бұрын
Welcome!
@Alexkonz77 5 күн бұрын
Спасибо, отличное видео 🪽
@UltimateDIY 5 күн бұрын
Welcome!
@vobchopper 5 күн бұрын
Looks good for the money
@UltimateDIY 5 күн бұрын
For sure better than I expected.
@socialwagner 6 күн бұрын
Nice video. Are you Romanian by any chance?
@UltimateDIY 6 күн бұрын
Thanks! Yes, I am.
@socialwagner 6 күн бұрын
@@UltimateDIY Bravo! Mult succes cu canalul; axeaza-te pe partea de review-uri. Sper sa cresti.
@UltimateDIY 6 күн бұрын
@socialwagner multumesc!
@hannesbernien8116 6 күн бұрын
Thank you! Such a big help! Saved a lot of frustration!
@UltimateDIY 6 күн бұрын
Welcome!
@rupaliarora5005 7 күн бұрын
cantt imagine technology has not changed in this years that I am still using this configuration.. kudos n thanks to you and 0 star for windows for creating this kind of problems to their user even after 7years
@UltimateDIY 7 күн бұрын
Welcome!
@knightslade2007 7 күн бұрын
Thanks for video
@UltimateDIY 7 күн бұрын
Welcome!
@CosmicJoeK 7 күн бұрын
Thank you for your detailed instructions 🙏🏻 Could you or anyone owning the desk tell me, if it is sturdy when elevated? Does it swing?
@UltimateDIY 6 күн бұрын
I consider it sturdy.
@catherinemantes8681 7 күн бұрын
Thank you 🙏
@UltimateDIY 7 күн бұрын
Welcome!
@muhammadumairumer5631 7 күн бұрын
Is it still working?
@UltimateDIY 7 күн бұрын
Yes.