Thank you very much😊

Thank you for the video, I have the exact same model and this walked through a successful fix! That unattached wire connector, at the end, befuddled me for a moment.

That is my model. I changed pressure switch and water inlet valve.....valve still hums, will not finish a cycle. I am throwing it away and buying a new one, I give up....LOL

It did not work for me, any other suggestions?

Wow, this fixed my dishwasher.

Good job. I carry a small metal pick set I bought for a couple dollars at Harbor Freight, works great to deal with issues like this

Thanks so much, it worked!

Wouldn’t happen to know a part number for that board by any chance, would you?

Thanks bud!

Bad dampers on the motor! 4 springs sit inside that shell on which the motor and compressor sit on :)

Sir i got same fridge 3 days ago but it’s not cooling or making ice 🧊 that much

Thanks for your advice Hameed. Not all Sub-Zeros have the condenser units down there though.

😂very very funny 😂🤣

I never paid attention to that center piece of the check valve that it can be removed for easy cleaning..grate job

Good job

Another great job.

We have the same model as in the video. I tried reversing the door on the dryer first but the screws that are on the hinge side are fine thread and they would not screw into the former receptacle side. I didn't want to strip those fine thread screws. The screws on the receptacle side are course thread. Can you offer some advice here?

A good idea is to thoroughly trip your breakers manually at least every 6 months .. this will more than likely prevent what happened to her . And thank you for helping her with door handle . Sadly a lot of people are in her shoes . Thank you for a great video 😊

Following your video I was excited that I could fix it myself. However, where the wire was completely broken was very close to the little curved plastic tube in the hinge mechanism. I tried to be gentle but the copper wire pulled out of the wire insulation completely. Now I have no access to that end of the wire. Can I take the hinge off (and I guess the entire door) and somehow retrieve enough wire to sodder the wires together?

Is the control board that need to be replaced if it keeps appearing or the touch pad ??

Thank you for sharing, apparently we all have the same issue here!!

wil the water sensor reset as well? I noticed that my washer wasn't sensing enough clothes so it only releases enough water

thanks brother i am already a subscriber. i have to work on one tomorrow

Kinda stuck at the first step. How do you remove those stupid covers for the screws holding the top in place without absolutely scratching everything?

So what do u do if it still doesnt spin??

I did that. After we moved it into house it wouldnt spin. I did your test all lights blinked..then rinse light.....they all blinked...water came out then now all lights r on.. now what???? I bought it used...then lights went off rinsed... clothes dont seem to get spin water out of them. What am i doing wrong or is it the washer

Those control boards can be pricey

Proof that silly mistakes can happen to even the best...

Worked perfectly thank you so much

Nice one, thanks mate!

Please how do I use the oven to bake

Man i never laughed so hard when you washed your face 🤣🤣🤣🤣🤣

Hi, just moved into a new house with the same Aga, followed your instructions and can see the spark but it’s not lighting, it was lit when we arrived so know it works, I’m not convinced it’s releasing gas when I press the button down, and tips to get it firing?

Thanks for this. Just finished swapping out my display. Back up and running!

Why aren't you narrating, saying what buttons your pushing I can see the start button but can't make out the other one

You need to reverse your washer door

Thanks!

Thank you for clear explanation and so much attention to details

I thought you were going to try to microwave a microwave

Lol I tell customer the same thing

Thanks Hameed for a helpful trick of the trade video. You're amazing! Going to subscribe now.

I have an electric Kenmore oven where the broil element will work, but the bottom bake element isn't heating. Would this be a function of a faulty control board or something else? Thanks for any help you can provide!

For someone with zero handyman skills I did this in 5 minutes. Perfect instructions!

Where do I get this part?

At 11pm my fridge wasn’t coming on and was beeping. I thought I was going to have to buy a new one. So glad this worked. Thank you so much!

Great Video! Thanks

Remove filter cover at the bottom. It is likely to not be draining so use towels to mop up water so you can see into the drain. There is a yellow plug. Remove but remember which way up it goes. Feel inside and check the rotor can spin freely, there may be a blockage. Once freely spinning replace yellow plug and filters and run a fairly hot wash with a tablet to dissolve fats. Call a tech if you can't get rotor to spin.

Very informative, thanks much!

Your the Maaaaaaaaaan!!!!!!!😊

It also will not fill up with water.