After watching all the side cutter videos destroying slide plastic rings I believe that you are a carburettor god 👍
@carlpilarczyk58975 ай бұрын
I have also found that placing the slide in almost boiling water helps in both removal and replacing the diaphragm.
@johnpaulbacunawa90205 ай бұрын
Any idea master?
@johnpaulbacunawa90205 ай бұрын
I have VMAX1200cc hard start ithink the starter can't rotate the cranckshaft
@sjuozhunki29 күн бұрын
It will be your starter clutch.
@memybikeni99318 ай бұрын
Goo vid. “Not sharp” = “Blunt” but I guess 5 years later you probably know that 😊
@irieman442 Жыл бұрын
very nice! Thanks for the tips!.. blunt or dull side is fine! LOL you almost said dull... LOL
@geamax1 Жыл бұрын
Thanks!
@denniswalker92192 жыл бұрын
Excellent! Just what I was looking for . I was just about to take it apart as I couldn't see another way to replace .
@marcos669902 жыл бұрын
thank you !!
@facetious_12 жыл бұрын
Damnit. I wish I have watch this one b4 breaking the poly flare ring. Now I feel like an idiot....its impossible on some years to simply slide it in place some some say....forcing it in with the dull side of a thin knife will work much better....dangit.
@robertisaacs68172 жыл бұрын
Thanx dude. Nice video. Love the "not so sharp side" part 😄. Blunt side is the proper term. 👍
@bobeden50272 жыл бұрын
I used my thumbnail to push the rubber in.
@crnivuk70923 жыл бұрын
Pozdrav Ranko gdje se nalazite vi ,u Hr ili . Ja sam iz BiH trebalo bi mi staviti jednu membranu od Yamahe XV 500. Prije smo ljepili ljepilom al pojede se i pukne
@rankozubonja23543 жыл бұрын
Osijek
@aminirani30053 жыл бұрын
👍
@sjuozhunki3 жыл бұрын
In English it is called the dull side.
@How2Wrench4 жыл бұрын
Such huge fans over here @ #how2wrench Nice work!
@twisterstudioproductionoff11374 жыл бұрын
Pozdrav Ranko, vidim da si majstor za zamenu membrana na VMax-u. Moze li neki kontakt?
Hello from Canada. Thanks Ranko i needed to know that. I have to replace the membranes on my Yamaha Virago.
@TheDUGERMAN4 жыл бұрын
о русский) спасибо за отличное видео)
@jaredvinje80704 жыл бұрын
Where did you get the membrane?
@theturbomedia14 жыл бұрын
use a credit card. or a shopping card..it/s much better
@bubbahanks4 жыл бұрын
Thank god I clicked on this video before following the destructive method suggested by those other guys. Mine was a bit easier and only took me a couple minutes. Thanks!
@boblolo39774 жыл бұрын
Great job, One thing though, You have to mark the position of the little "ear" on the edge of the membrane and mach it with the new one, that will orient the holes at the bottom of the sliders correctly in the carburetor.
@bobeden50272 жыл бұрын
how should the holes in the bottom of the slide be aligned? I have 3 holes in mine. Any ideas?
@Alexander_Meyer4 жыл бұрын
Amazing! Thanks man
@Drtikol694 жыл бұрын
super video
@lennardlennard4144 жыл бұрын
Not sharp side of the knife is the dull side.
@alladingrc5 жыл бұрын
Thanks man. I do it with that way and its works. Ich habe mit diese Methode gemacht und ich schaffte. Λειτουργεί παιδιά, το δοκίμασα όπως λέει και πετυχε. Thanks!!!!!
@mateuszlesniak88695 жыл бұрын
Thank You for this video. I have just buy a new membranes for may new motorcycle Yamaha xs400 se. When I saw the instruction, that I need glue the membrane and top plastic ring. I was thinking, that’s not a good idea!!! You’re method is better than instruction because You not damage anything.
@donmaribras4 жыл бұрын
Hi. Where did you get your membranes?
@pomonabill2204 жыл бұрын
Where did you get the membranes???
@MsIvicao5 жыл бұрын
Jedino mislim da je problem jer nije isto gdje će gledati ono ispupčenje na vrhu membrane. Ono bi trebalo biti u točno određenom položaju na klipu kako bi klip kada se instalira bio pravilno pozicioniran... hvala za video baš me čeka promjena jedne membrane...