Can i do this with '06 Nissan Xtrail?

Man this woke my maxima back up

I tried this several times and got it. Thanks.

I have two '18's. An Explorer and F150. They have two separate chains and two tensioners. I paid $38 ea for the tensioners at the dealership. The thing that's annoying is they don't offer a complete kit to replace the timing set. You have to buy everything separately. If you're not boosting, you're driving like a grandma and people are honking at you. People think the timing is rattling upon startup but the majority of the time, it's the turbo waste gate arm. I highly suggest replacing your water pump and oil pump if you're doing a timing set. Yes, you can change the oil pump without pulling the pan. The thing that sucks is the oil pump cost alone is over half the cost of the timing set. We get around 18 mpg in the city and around 22 on the hwy. But we drive like we stole them. Our hwy mileage goes up in the mid 20's if we actually did the speed limit. My F150 has the ext fuel tank and allows me to go 600plus miles between fill ups. And yes, I pull 12k lbs with mine as it has the max tow package with a 13200lb tow limit. It pulls and stops easily. My son has a 5.0 in his F150 and it does very well also. His just hit 200k and still the original timing set with no rattle. My F150 had 175k miles on it before I did the timing set.

LOL this is why it costs like 900$ to have your starter motor replaced. Or a 1000$ spark plug change. You do not need to spend all the time and effort removing the steering wheel. Holy hell. Did you forget you were making a how to video and not trying to pad the bill with "labor"?

Well, this tool is useless if the shaft threads are not there due to heavy rust or stripped 😂

What if you have a v8 in a v6 body would it still work the same ?

Thanks dude

I just bought a 09 Murano and replaced the Accelerator pedal sensor and got no results.(I was told this was the issue) It doesn't rev up. Is this the limp mode low tranny fluid? I didn't check it. I did hear a loud whining when 1st started, I thought it was the pw steering pump. Thanks much for any help.

is that works on Altima 2013?

If you're not stepping on the accelerater at all in step one why should tou make sure its released

I dont understand thix cuz electron flow is negstive to positive...and conventional current is supposedly positive to negative

Programming the second key won't work for my 2009 Silverado. Help!

Will this process work on a 2019 Titan 5.6?

Thank you for the explanation, I have seen this 'procedure' on other videos but all of the steps were combined and not needed once completed. This worked for me the first time , so I made notes in my Haynes manual for next time.

I’m actually mad at ford for this one. $4000.00 repair for a part replacement that originally used to be a very cost effective Hydraulic system. I want a truck that goes and turns. Why make it complicated with ridiculous parts like this. My 1995 mustang still steers just fine, but my “built Ford tough” f-150 can’t make 225,000km without needing a repair worth 10% of the entire vehicle brand new.

Wow the guys is genius, the accent was excellent for my comprehension ❤

Can I do this even with a vehicle using a sterling box

The only thing I need to know is I absolutely will never own one I consider them to be junk

Good video

Fuck Ford and its PATS system. I had enough. Whos got money for all that shit? Not me. Im a poor loser. I junked my POS mustang I'd had for 20 years. Ford got me, alright. Never again, Ford. It will rot away to nothing in the woods. And i will piss on it every time i see it.

Hi there, Quick question - I just got my EPS rack replaced on my 2011 F150. A few days after getting it back from the mechanic I have been having transmission sensor issues. A friend plugged his code reader in and got the code "P0720 Output Speed Sensor Circuit" Could this be an issue from incorrect programming and calibration of the new EPS rack? Please let me know. Thanks

I see this doesn’t work for my 2009 Malibu.

After I clean the throttle body on my 2007 Chevy Tahoe it was idling at 3200 RPMs . couldn't get it to go down . Finally I turned on the AC on high and it pulled the RPMs down enough to be able to drive it

Y’all be saying make sure the pedal is fully released so am I supposed to pressed down/hold the gas pedal down Lol

Thank you very much for the precise step by step video. I would like to add on to this procedure as most batteries are below 13 V, so I if you can connect a booster cable with another vehicle then your voltage should be around 14.5V. Then try to relearn, mine worked the first time after I had 4 failed attempts without a booster connection.

Does this work with the Nissan Almera classic (QG16DE engine)

How do you know if you are in the boost and how do I stay out of the boost

I wouldn't trust cardone's claims of reengineering. The rear wiper motors on older Ford Explorers and Expeditions are known to fail due to the internal plastic gears. Yet cardone continues to sell those wiper motors with plastic gears and they still fail early, just as they did 20 years ago.

what happens if u don’t hear the sound ? done this like 5x and never heard anything

Worked

Could it simpler, face west now hop on one leg , good video man

👍👍

What a BRAIN on this tech. He really knows and loves his job. He's the guy that works 10 hours on cars and then goes home and reads about cars and then goes to bed and dreams about cars 🤙🏽♥️

Is this applicable to a 1998 Infiniti Q45? Thank you!

Do you have any videos on the newer push button from 2020 and up. I'm having some crazy start issues with my 2021 gmc 2500hd 6.6 diesel and my security module is stuck in learn mode.

Do you ship to Mexico? It is rack&pinion for DAEWOO MATIZ 2010 in your catalogue? Regards!

I’m going to try this on a Chevy Malibu 2012

Did the procedure and My RPMs are back to normal but check engine light is still on. Does this mean I didn’t do it right ?

How do you do a brake pedal switch relearn on a 2012 chevy silverado

Hello brother, does it work on Chevrolet Optra 2011 engine 1.6? I have changed the throttle body to a new one but when I start it up the RPM stays below 1000 or on 1000, may you please help me, thank you very much

I cleaned my throttle body 2010 Silverado and my engine ran at over 3000 rpm there was no way I was going to keep my engine running for 3 minutes.

fully depress the accelerator peda Wait 20 seconds and Fully release the accelerator pedal within 3 seconds after the MIL turns ON (((((((((( NOT RUN in wait 3 seconds in stop MIL ) and ON

If I start 4hi and turn the steering wheel to the end, the car stops and does not move as if something stopped the car.

Good power, decent fuel economy thus endeth the pros! Cons not very reliable & high maintenance cost. Plus a lot of failures Ang not just from lack of maintenance! The 4 cylinders are much worse with coolant in cylinders & high failure rates!

Hw do I reset if I hve push button??anyone

2010 altima push button

I have a 2012 nissan versa 1.8 s hatchback. Changed the spark plugs and ignition coils now service engine light is on. P0123, P0113, P0223, codes popped up. Cleaned TB and light is still on. Should i do this to get rid of these codes and the service engine light? Thank you!!

Does new or remanufactured last longer. That’s all I car about and don’t know

I fkn hate Nissan smh