At 0:32 what is that pipe with the white plastic and metal tip used for that goes into the top of the engine into that ring thing?
@JacoBadenhorst5 күн бұрын
PCV hose. Positive Crankcase ventilator valve.
@Zachgalldeon7 күн бұрын
vice grip for clamps works much better. give i try.
@JacoBadenhorst7 күн бұрын
@@Zachgalldeon this is why I like this platform. Thanks for the advice. Will give it a try for sure!
@joshuagreen73528 күн бұрын
Could you quickly explain how to remove the passenger side airbag panel please?
@JacoBadenhorst8 күн бұрын
@@joshuagreen7352 I tried as I just wanted toe remove the airbag panel in this video. You have to remove the whole dash... That's the only way I could get to it. If there is someone else that knows I will he eager to listen.
@dbaznr10 күн бұрын
Keep the wrench in the undo position, so when you turn the tool to cut the wire, it tights further the loops. Also instead of the front hole, install a small rod, to constrain better the wire near the edge.
@itumelengjunior729111 күн бұрын
200n/m for the rear bearing???????????
@JacoBadenhorst11 күн бұрын
The Ford Bantam user manual actually Specs 235nm for the drum retaining nut
@steviepelser447915 күн бұрын
Hello , ive replaced the timing chain but still has a noice , what else can i look at ?
@cixxnine692715 күн бұрын
Hi jaco i have a ford bantam crank but no start please help...
@punaforager17 күн бұрын
can't find the fuse....?
@SamsonMoyahabo19 күн бұрын
Ford bantum rocam how to put head sens
@Zimbabwerailways22 күн бұрын
Whats your opinion on da anc coalition
@mohamedharbaoui255725 күн бұрын
interrupteur de meule à disque
@My-Amazing-Life28 күн бұрын
Haha
@SiboneloXulu-u6mАй бұрын
Vidoe bleeding clutch please
@dokesz530Ай бұрын
are bosch parts like coil and wires are good?i bought motorcraft sparkplugs i dont like ngk but need to fix the 4rd cyl misfiring issue.
@JacoBadenhorstАй бұрын
Yes you should be ok with BOSCH aftermarket coil and ignition leads.
@dokesz530Ай бұрын
@@JacoBadenhorst thanks.i ll test all wires and coil if there is a bad contact.i ll buy bosch then.
@mawandengcai23Ай бұрын
Who can you recommend me to fix my hand break. It barely stops the car from moving
@JacoBadenhorstАй бұрын
Any reputable break and clutch shop. It may be that the rear brakes are worn. That puts slack in the park break cable as the park break only actuates the rear brakes. The slack has to be taken out of the cable if the tear brake shoes are not replaced. It's easy. A 10mm spanner is used to tighten the cables after removing the leather boot around the park brake handle.
@jxms3729Ай бұрын
Dankie oom, die video het baie gehelp👍
@JacoBadenhorstАй бұрын
Groot plesier.
@AhmedNabighАй бұрын
You used a lot of sizes of ropes, what are they
@JacoBadenhorstАй бұрын
I honestly cannot remember the sequence. 3mm, 5mm, 8mm, 10mm, 12mm. If you follow along I give the exact lengths and diameters to make a short bull whip. Just adapt the lengths for a longer whip.
@colinbreedt3804Ай бұрын
My rocom was idling then just died the stater won't even turn over dash lights to come on
@JacoBadenhorstАй бұрын
Electrical issue. Did you find the problem?
@alexpittendrigh4600Ай бұрын
Dankie Jaco. Stem saam. Haal die engine uit. Goeie videos. Help Baie
@sanctifiedandpurified2299Ай бұрын
Thanks for these videos... EC has a gap in having quality mechanics... Im lucky to be driving this beast. Recently it was mixing or on the genesis of it. The fortune part is that i saw in time, sad part i took it to the wrong hands that left milky reduce on the engine top cover. 2. Also struggling with the car losing power, and stalling, eventually stopped (cranks with no luck of starting). Im thinking of changing the coil pack and plugs myself
@JacoBadenhorstАй бұрын
Coil pack and plugs is easy to do yourself. Just make sure you don't swop leads.
@xXSlyfoxMinionXxАй бұрын
Option A and any hammer, you've got two tools that are way better at B's job.
@JacoBadenhorstАй бұрын
I feel exactly the same. A "multi-tool" is never as good as the individual tools it replicates.
@prano550Ай бұрын
nice ,but why are you armed while working on a trailer lol
@JacoBadenhorstАй бұрын
The neck of the woods I live in.
@PulaneMolopaАй бұрын
How do i bleed my clutch on Ford bantum
@JacoBadenhorstАй бұрын
On the concentric slave cylinder there is 2 ports. One is the hydraulic input. 2nd is the bleed valve. You will need 2people. Depress the clutch. Pedal. Open the bleed valve to release pressure. Close bleed valve. Release clutch pedal. Depress clutch pedal. Release bleed valve. Close bleed valve release clutch pedal. Repeat till all air is removed.
@Martin_3DАй бұрын
Gedore is very popular in Brazil and has a factory there. They are very proud of their manufacturing and stamp the origin on the packaging and tools.
@Martin_3DАй бұрын
Gedore is very popular in Brazil and has a factory there. They are very proud of their manufacturing and stamp the origin on the packaging and tools.
@jakobusmouton42972 ай бұрын
Thank you very much for this video I am doing my timing chain, cv joints axal completely new, my Bandam is making a rumbling noise when she starts up, so I hope by replacing the timing chain and components with the oil pump that that should be gone otherwise it's in the head, but I don't hope so. Any Ideas it sounds like the oil is priming for the first couple of seconds, MY 1600 Bantam has 300 000 km on the clock and.
@jannieglad65132 ай бұрын
The last time i took out the gearbox to remove the sump i decided enough is enough. I drilled 2 holes in the bell housing exactly under the 2 bolts and use a small ratchet and extension to remove the 2 bolts. Worked like a charm for me.
@WesleyThompson-ov6yd2 ай бұрын
Hi Jaco, Great work on the videos, really helps alot. What could be the cause for gearbox oil leak through the breather, Thanks.
@JacoBadenhorstАй бұрын
Probably overfill. There should not be pressure in the gearbox. and there is no way any oil can leak into it.
@BhekiManzini_SA2 ай бұрын
Heelo Jaco, is it possible to replace valve stem seals on the rocam without removing the top?
@JacoBadenhorst2 ай бұрын
Should be yes. one cylinder at a time. Feed a piece of rope into the cylinder through the spark plug hole. Hand crank to compress the rope in the cylinder. This will prevent the valve from dropping into the cylinder when you take out the valve spring.
@Hp_Magic2 ай бұрын
Thank you it helped me out after 2 yrs of uploading 🙏
@JacoBadenhorst2 ай бұрын
It's my pleasure.glad I could help.
@ceciliamabothe21182 ай бұрын
Hi Jaco, how do we get hold of you if need your services?
@JacoBadenhorst2 ай бұрын
Good morning. Please let me know what servic you require?
@user-xe2jt1zm1r2 ай бұрын
Gedore Blue Türkiye 🇹🇷
@job38four102 ай бұрын
Isn't there a way to make a wire hose clamp that dont waste so much wire.........
@JacoBadenhorst2 ай бұрын
This one works way better with much less waste. kzbin.info/www/bejne/fZ6vnJ-uoJ5qsLs
@steveborgresistance83102 ай бұрын
B ! Every day💯
@kenneths.93152 ай бұрын
This helped zero. If it breaks I will buy a new one.
@JacoBadenhorstАй бұрын
True, but if I fix it without it costing me anything, I can buy a different tool of that value. But each to his own I guess.
@mick1gallagher2 ай бұрын
Ridiculous nonsense hose clips are very cheap
@HadeerHaitham-pn9qn2 ай бұрын
Can you translate it into Arabic?
@dirkkruger95722 ай бұрын
Mooi job Jaco
@stefandejager35122 ай бұрын
How did you know that the head blew? My bantam is overheating after replacing the water pump, radiator. And themestate as well. And what must i replace whe. i do the head
@JacoBadenhorstАй бұрын
Got excessive pressure in the coolant reservoir. Plus sputtering and uneven idle. Did you replace the temp sensor? the aftermarket ones are different from OEM. You can take the head to any reputable engineering shop that specializes in it.
@LegjobbNap2 ай бұрын
great!
@johansteenkamp64812 ай бұрын
Hoe lank het dit jou gevat om hom weer aanmekaar te sit?
@JacoBadenhorst2 ай бұрын
9:00 begin strip. 16:20 als klaar en op hulle plek.
@L35inColorado3 ай бұрын
Thanks for sharing this!
@JacoBadenhorst3 ай бұрын
Absolute pleasure.
@Zimbabwerailways3 ай бұрын
You alive
@bhutimakakula3 ай бұрын
thanx for your helpful and informative videos, what i need to know is whether a bad water pump can contribute to oil mixing with water?
@JacoBadenhorst2 ай бұрын
Bad water pump will lead to overheating that will lead to a blown head gasket.
@bhutimakakula2 ай бұрын
@@JacoBadenhorst Thanx man for that clarity🙏. Is there a video where you are setting a timing chain maybe?
@jasonflynnpp1443 ай бұрын
Great video
@SidneyBromfield3 ай бұрын
interesting did you test the etc switch on the thermostat housing because oem is no longer manufactured at ford ? please bear in mind cold reading on ohm meter of the ect swtich cold is supposed to be 5 kilo ohms and just above 2 hot?
@JacoBadenhorstАй бұрын
This explains a lot. Had a previous issue where the replacement sensor(aftermarket) was "faulty" out of the box. Thank you very much for pointing this out. This is why I love this platform.
@SidneyBromfield3 ай бұрын
fiesta runs on a duratec motor with a cambelt. rocam is a rollerbearing camshaft as the name implies and runs on a camchain. Yes most of the non-OEM parts are no longer manufactured meaning you have to be careful when purchasing after market parts. epecially the ECT Switch as their ratings are totally incorrected on kilo ohms
@LEROY87813 ай бұрын
Can you please assist, where can i buy tripod cv boots for my bantum, or can i use the normal CV boot
@JacoBadenhorst3 ай бұрын
AutoZone or midas will be able to supply you. A Normal boot wil probably not work.
@kokka2423 ай бұрын
Ek het jou video gebruik om my head te ruil nou wil hy nie start nie so dra hy swaai val die petol gauge na E toe enige idee wat kan fout wees?
@JacoBadenhorst3 ай бұрын
Sounds like you have a dead battery or bad ground.
@kokka2423 ай бұрын
Thx will check it to day
@kokka2423 ай бұрын
Sprayed all the electric connectors cleaned the earth bonding half a can of quick start and she is running well baie dankie