Does any one know how to save them as a jpeg format?
@PoppyHillDesigns7 сағат бұрын
@@paulcotesr5623 Unfortunately the software was discontinued 4 years ago and is no longer available.
@paulcotesr56233 күн бұрын
where can i find this ? program ty
@jackscrafts92029 күн бұрын
TY
@chopchop516610 күн бұрын
This is the clearest, most succinct tutorial I’ve found for using layers in XCS. Thank you!
@PoppyHillDesigns10 күн бұрын
Thank you. So glad you found it helpful.
@joshchatasegich643726 күн бұрын
I am trying to print my own designs for some cabochons, would you be able to share with me what type of printer you use
@PoppyHillDesigns24 күн бұрын
I use an Epson inkjet printer, set on "best" quality. The paper is a lightweight cardstock. Another alternative is to take the file to a copy center, like Office Max, Staples, and have them print onto cardstock for you. Those image are more vibrant because they are printed with a laser.
@stephaniearchuleta968729 күн бұрын
Do u spray anything on them when they are done
@PoppyHillDesigns21 күн бұрын
You can apply food grade linseed oil.
@loaferscorner1600Ай бұрын
I enjoyed your videos, one question do you any problems cutting the 1/4 wood with this laser.
@PoppyHillDesignsАй бұрын
@@loaferscorner1600 I did 2 passes and that worked for me.
@DaleGustafson-n2fАй бұрын
Your tutorial is excellent As an novice to using a laser machine, I really appreciated the detailed step-by-step coverage of the design process and your use of the cutout sections was brilliant idea. I hope you keep making more tutorials.
@PoppyHillDesignsАй бұрын
@DaleGustafson-n2f Thank you. I appreciate your comment, and I'm glad that you found the tutorial helpful.
@judykritikos29532 ай бұрын
You said "trivet" at the end - can these Dollar Tree glass pieces be used as an actual trivet - straight from the oven or stove top??? That'd be nice!
@PoppyHillDesigns2 ай бұрын
Unfortunately no, as this would activate the sublimation ink and destroy the image.
@gambo472 ай бұрын
please help, I have a 20mm thick piece of oak but cannot find anywhere any help for what settings to use when using the honeycomb bed, which shelf if any I should be putting the oak board on, and then which settings I ned to change on the software before processing it... thanks
@PoppyHillDesigns2 ай бұрын
Remove the honeycomb and place it in the first slot down. Place the board on it and see if the top of the wood comes up to the opening, if not you will have to place something under it to make it level with the opening. Change the "MODE" to "Baseplate Removed" and perform the automeasure. If that comes back OK choose your settings from the materials panel. Use the new materials suggestions to choose the look you want.
@gambo472 ай бұрын
Thankyou for that, I'm. Amazed that having watched so many videos, read loads of guides I couldn't find any that describes exactly what I was looking for. @@PoppyHillDesigns
@fionabentley6342 ай бұрын
Thank you for this tutorial. I am new to this machine and software and am finding it hard to get my head around, this tutorial was really helpful. thanks again
@PoppyHillDesigns2 ай бұрын
Glad you found it helpful. These machines are a lot of fun.
@janlewis23863 ай бұрын
Very helpful video, I am new to laser machines and have this one. Thank you very well explained video.
@PoppyHillDesigns3 ай бұрын
So glad you found it helpful.
@djp8283 ай бұрын
what would be the settings for an xtool d1 pro 20w?
@PoppyHillDesigns3 ай бұрын
I don't know. I have a 10 watt machine. Try starting low and building up until you find the right combination.
@pascalebretagne84284 ай бұрын
thanks a lot for this excellent tutorial, I discovered news software functions with this vidéo. I'll be there for the others episodes!!
@parisharrison66394 ай бұрын
Thank you for this video. I am excited to do this.
@PoppyHillDesigns4 ай бұрын
Thank you Paris, glad you liked the video.
@danield.794 ай бұрын
I just received my M1 yesterday and was browsing several videos trying to learn how to use it and came across your channel. SOO GLAD I DID!! You are very thorough, and as an amateur, that makes all the difference in the experience. I am a visual learner, so your step-by-step instructions guides me through the process with ease! So glad I found your channel. Looking forward to learning all I can about using the M1 and V 2.0 of Creative Space.
@PoppyHillDesigns4 ай бұрын
Thank you Daniel, so glad you liked the video and found it informative. Good luck with your M1, I really enjoy mine.
@hknjue4 ай бұрын
Fantastic, thanks for the tutorial.
@PoppyHillDesigns4 ай бұрын
Glad you enjoyed it. Have a great evening.
@damrs2yall4384 ай бұрын
Awe Mann ! This is such detailed information! Thank you thank you, really need this tutorial for all crafters! New Subbie for this too😊
@PoppyHillDesigns4 ай бұрын
Thank you, I'm glad you found the information helpful.
@gloria65085 ай бұрын
What is the advantage to doing this versus printing on a color printer and framing? Is the image embedded into the wood, or is the wood used only to hold the paper in place?
@lisaedmonds94835 ай бұрын
It doesn’t use expensive printer ink and looks really cool and detailed
@djp8283 ай бұрын
Because there's no sense of statisfation that's the main reason people enjoy arts n craft.
@Jemmyjo5 ай бұрын
You, do not have enough views!!!! I hope you see this, because you are showing what NO other crafter is showing. This is needed!!!
@PoppyHillDesigns5 ай бұрын
Thank you! KZbin ranks channels by how frequently you post videos and how many views. Time does not allow me to post as often as I would like. I'm happy that you enjoy my content please share my link to others that many benefit from it. Thank you for watching.
@Jemmyjo5 ай бұрын
@@PoppyHillDesigns I will most definitely share your videos. I wish there were more videos like this. I don’t think I have ever seen one and I have really needed it. I do sublimation, htv, rhinestones, designing, etc, but being able to get those measurements will make the project look better and go faster. You should keep at this as time allows! I get it. I have a farm that takes my time. I Have to grab my time when I can.
@rps16895 ай бұрын
does the glass cabochon need to be a little smaller than the bezel?
@PoppyHillDesigns5 ай бұрын
I have found that when I buy 25mm cabochons and bezels there are slight variances in the sizes. Most of the time it works out fine.
@pamelagriffiths46435 ай бұрын
This was great thank you. I don't have the same laser machine but I am hoping I can incorporate what you showed using Shilloute Studio and then pulling it into Lightburn. I'm not sure if you can design in Lightburn as I have only used it so far to transfer my files to cut on my machine.
@janesfavsvideos5 ай бұрын
@viridianaflores33136 ай бұрын
What do you use so the wood won't moved ?thank you
@PoppyHillDesigns6 ай бұрын
Nothing, it's heavy enough so it won't move.
@SweetPstube6 ай бұрын
I'm looking to make this but don't quite see how you attached the hangar - doesn't seem to be covered in tutorial. did you add another spacer at top? how did you get the little flower in center top hole attached - nice touch i would like to incorporate.
@buddysmith70806 ай бұрын
Thank you for the very detailed instructions. How did you know what to adjust the settings to?
@PoppyHillDesigns6 ай бұрын
I tested on another bit of wood to get the settings that I wanted. xTool has a newer version of their software out that gives you a visual of the settings, that will be helpful.
@jeangrandy86726 ай бұрын
Do you mirror the image?
@jeangrandy86726 ай бұрын
I’ve been told that after about 3-4 months the image starts to fade or get foggy!! Is this true???
@PoppyHillDesigns6 ай бұрын
I didn't see any problems with my project until recently. It does seem to look a little foggy but that 2 years in. I think the 651 Oracal vinyl is key to the success of this project.
@jeangrandy86726 ай бұрын
@@PoppyHillDesignsnow I’ve been told that if you use thermal laminating sheets as opposed to the Orcal 651🤷♀️ I want to try to do it, but I don’t wanna sell it to somebody and have them come back to me a few months down the road and complain about it
@MissLilRasta8 ай бұрын
Hi, is it okay without homecomb or riser?
@PoppyHillDesigns8 ай бұрын
Yes, you may have some charring on the backside.
@SweetPstube8 ай бұрын
i'm excited to try out some of your ideas. do you think it would work to use only 2 pieces of wood - no spacer - glued together. glue photo to backer then top with a resin dome?
@PoppyHillDesigns8 ай бұрын
Sounds like a great idea!
@12mgreene8 ай бұрын
On the $Store on did you put the vinyl on rough side or the smooth side?
@PoppyHillDesigns8 ай бұрын
Smooth side.
@Mrs6218089 ай бұрын
Beautiful
@djr30089 ай бұрын
Just an FYI. You helped me so I will help you as well. When you want to brake down your text to more then one line just put the cursor where you want to split the lines and hit enter. No backspace or shift key needed. (Copy paste), highlight object then right click on the object, hit copy then hit paste close to where you want it move to then make your adjustments. No need for c-control or v- control. You can also go to shapes to get a circle or square. <--- to each his/her own on this one. I like to use shapes and unlock, then size it. Either way works. Much of what I am telling you are updates or improvements they made to Creative Space. Another great video TY, I leaned new tricks from you once again.
@FRANKSMITHIII9 ай бұрын
Planning on making my own earring brand! Gonna watch this when I get home. Thanks so much!
@PoppyHillDesigns9 ай бұрын
Hope you enjoy it. The possibilities are endless with earrings!
@djr30089 ай бұрын
Thank You. Finally someone that is teaching something, not trying to sell something or taking us along on a joyride while they get views yet are learning themselves. I learned a lot watching this video.
@PoppyHillDesigns9 ай бұрын
Thank you for your comment. I do my best!
@tammya97709 ай бұрын
Your tutorial is fantastic! You make it so easy to follow along. Thank you! I am new to laser cutting and the software. Excited to follow you and learn more. Do you have a video/file for the tree ornament hanger? Thank you!
@PoppyHillDesigns9 ай бұрын
Hi Tammy, thank you so much for your comment. I'm glad you found the tutorial helpful. I sent you information regarding the tree file via my etsy store.
@tammya97709 ай бұрын
Thank you!@@PoppyHillDesigns
@lisamiller47429 ай бұрын
Thank you for a great step by step tutorial. I have one question. Did you have to change your settings when cutting/engraving on the painted wood? Great video.
@PoppyHillDesigns9 ай бұрын
Thank you for the comment. I didn't change the settings for the painted wood.
@arizonaheatwave40809 ай бұрын
Another fantastic video!! I can’t thank you enough for the precise step by step tutorial, I struggle with computer stuff and I have learned an invaluable amount of info by just watching 2 of your videos! Thank you so much!! 😁
@PoppyHillDesigns9 ай бұрын
Great to hear!
@arizonaheatwave40809 ай бұрын
That was a very very good tutorial! Thank you so much!
@PoppyHillDesigns9 ай бұрын
Thank you, I'm glad you found it helpful.
@arizonaheatwave40809 ай бұрын
it would be fantastic if you did more tutorials with this laser Xtool M1 Thank you😁
@PoppyHillDesigns9 ай бұрын
I have several already on my channel and plan to do more. Be sure to subscribe so you don't miss them. @@arizonaheatwave4080
@bevyjeanheyrman85379 ай бұрын
Replay-thanks
@JustMeValerie69 ай бұрын
I came to this video only to learn what temperature and time to use to sublimate on a metal license plate. What a great video, well done, very thorough, no BS. I watched the whole thing and learned a lot. Thank you for sharing your knowledge, I appreciate it. 😊
@PoppyHillDesigns9 ай бұрын
Thank you. I'm glad you found the information helpful.
@hknjue10 ай бұрын
Fantastic!
@PoppyHillDesigns10 ай бұрын
Thank you, glad you enjoyed the video.
@bchollin10 ай бұрын
Thank forthe tutorial. Excelent.
@PoppyHillDesigns10 ай бұрын
Thank you. Glad you enjoyed it.
@DanielMartinez-ju4qu10 ай бұрын
Great tutorial. I feel that I can do this with these instructions. Thanks.
@PoppyHillDesigns10 ай бұрын
Thank you Dan, I'm glad that you enjoyed the video and found the instructions helpful.
@deegodess255310 ай бұрын
NICE 😍
@PoppyHillDesigns10 ай бұрын
Thank you!
@jeannieg444010 ай бұрын
That is so nice, excellent tutorial. Thank you.
@PoppyHillDesigns10 ай бұрын
Thank you for your comment, so glad that you enjoyed the tutorial.
@jeffcooper246411 ай бұрын
Great video & nicely explained. I’m just waiting for delivery of my M1 but have already been busy designing earrings, so seeing your video was very timely. Slightly confused about the need to mirror the copied image? I will not have the honeycomb bed, just the prism rods, so not sure how best to secure your basswood?
@PoppyHillDesigns10 ай бұрын
Thank you for your comment Jeff. I don't think you can secure the wood to the rods. I would suggest that you keep the rods close together when cutting smaller things. The mirror image is useful for earrings that are no symmetrical. Hope you enjoy your machine.
@TheScrapGranny11 ай бұрын
You did a great job explaining each step. I just ordered the XTool M1 last night. This is exactly the tutorial I needed! Thank you!
@PoppyHillDesigns11 ай бұрын
Thank you, I'm glad you enjoyed the video.
@crankiecrafter656211 ай бұрын
Thank you, BEST video i found. Instruction were fantastic!
@PoppyHillDesigns11 ай бұрын
Thank you, glad you found it helpful.
@amandafranco817411 ай бұрын
I’ve tried everything and sprays, coats, different glues, waiting 5 min, etc everything and I swear I’ve Ive every KZbin video on it and mine always has bubbles or bleeds or both. I’m gonna try it this way again I think it was better not cutting it out first. Ty