Andreas Gorivo Buducnosti H2O

Пікірлер

@litmantoolit5881 24 күн бұрын

hi just a question my battery cuts off as soon as the scooter is under load is this a solution

@ElectronicRepair.Serbia2023 9 күн бұрын

Yes this is the solution.

@brandonkucksdorf8663 Ай бұрын

How in the world did he get 54v output? I can only get 18v. Please help!

@bantushakya5097 2 ай бұрын

Hi sir

@MatthiasSnoep-yf6rg 2 ай бұрын

Do you have a partnumber? I have a problem with the exact same chip, but can't get a replacement part because a of a burnt number

@zvonkodurdov5926 2 ай бұрын

Gdje je servis vaš,i gdje mogu nabaviti nove baterije za ovaj usisivač.

@benomimo8265 2 ай бұрын

The problem with discharging the only way it 's to change bms

@davidecer8180 3 ай бұрын

hi, I followed your tutorial, everything is fine but why does the voltage go back to minimum if I connect something?

@joeysmith646 3 ай бұрын

Can you change the discharge plug too?

@dilipraharka4988 3 ай бұрын

Burn out😂😂😂 same problem with me

@riseofgamer7518 3 ай бұрын

What is the total price of full restoration ?

@user-qk8sg2cm9i 3 ай бұрын

Što da ne,vidoko mu usisna grana tojest filter za vazduh a to je najbitnije.

@gotagboa 4 ай бұрын

What liquid and cloth did you use to clean the screen layers? Thank you

@gotagboa 4 ай бұрын

Alcohol ethanol and tissue paper? Thanks

@user-cz6kg6td4j 4 ай бұрын

😂👍🚢

@lj-qd1tt 4 ай бұрын

CAR 😅😅😅

@jasambre-gc3or 4 ай бұрын

pa ode bus na odpad

@damianwebb7422 5 ай бұрын

Can you pls explain which wires you connect. I have same battery but I can’t get it to charge & give output over 4.6v

@dopeydave5317 5 ай бұрын

Is this just for the charger or to bypass the battery i have done a diffrent bypass an can get 44v but need to be able to cxharge now battery works fine on bike

@dopeydave5317 5 ай бұрын

I have the same battery but cuts out on full throttle

@dopeydave5317 5 ай бұрын

Myn dose the same did u get around this problem mate

@smpbih 5 ай бұрын

To si ti nešto sjebao

@robertorodriguez1845 5 ай бұрын

Hey man had a question for ya. I ended up taking off the wires for the battery screen and was wondering if you had a picture of how they are supposed to go.

@goranperic4471 6 ай бұрын

Koji je ovo smrdljak od grada kada imaju reku na putu😂

@jackbucko1598 6 ай бұрын

How do you charge the batter and active the screen

@criodna 6 ай бұрын

Hello Andreas! There is a burn capacitor in my G2 tower. I want to buy it and sold it in order to fix it. If I send you a photo of the mobo can you recognise the info of the capacitor so I know which one to buy?? Thanks

@user-zs5ut4kq3u 7 ай бұрын

Hi everyone, the bypass works partially or only for charging but for discharging it doesn't work. You can see the right voltage with a tester but if you try after a few seconds the voltage will turn off the only method which is the simplest is simply change the output port in the BMS. I attach a video that explains it well the title is: Bird es-400a | bms Bypass | Tutorial | DIY

@jnygaarddk 8 ай бұрын

How did you enable the output??

@ElectronicRepair.Serbia2023 6 ай бұрын

I don't do nothing yast upgrade the charging conector.

@Mou_Lom 8 ай бұрын

Ни так так бы сразу показывали китайцы, для сварки стали 0.8 надо 220 ампер, только на видео металл перегрет

@xwatchid 9 ай бұрын

can you use any reasonable 26V supply?

@emekaobi2727 9 ай бұрын

Good day sir. I want to ask a question and it is this, can a system still work if a component is shorted to the motherboard. Have been experiencing a issue with my system when used with the battery it works for two days after that it will refuse to power on not until I remove the battery for one day before it works again, at this moment it refuses to on nothing I'll do will make it come up not until I wait for one day.

@ElectronicRepair.Serbia2023 9 ай бұрын

The buton its stacked whit glue mast pull hard

@FPRTuning 4 күн бұрын

Is ot 18650 or 21700 cells in these

@CardsMoto 9 ай бұрын

I know this is old But phew, it gave me confidence to do it to my Legion 5 lcd, Success operation 🎉🎉🎉

@joesoefismail9697 9 ай бұрын

Where can I repair my MPF Drive? Thank you, Joesoef. The Hague, nl

@mysiak8237 9 ай бұрын

Did you pry the bottom out ? I removed all the screws but it's still stuck

@georgewhite9002 6 ай бұрын

SAME DID YOU FIGURE IT OUT?

@mysiak8237 6 ай бұрын

Remove all screws and pry it off with a lot of force no other way. but you still won't be able to remove the cells from the metal casing because it's encapsulated in some sort of resin. I tried cutting it very carefully but still managed to pierce them. Unless you have an angle grinder better to just leave it in the casing and use a 50V to something useful converter.

@fluorescentblack4336 4 ай бұрын

@@mysiak8237 How are you charging one of these? I have several and want to charge them safely

@user-pz6jl6jv2z 10 ай бұрын

How do you open the unit?

@karabomichisi1460 10 ай бұрын

Hey I have a ProBook 650 G2 HP laptop and it stopped charging, I was using it and saw that it's low so I put a charger in and it was charging fine until it suddenly stopped now when I try to hold the power button for a few seconds without the charger in it flashes an orange color on the led but when I put the charger nothing happens but turn on at the caps lock button please help

@laptopDoctorKZN 11 ай бұрын

Hi. I need a picture of the psid section please if u have

@EliteForexTraining 11 ай бұрын

What if the outside screen got gracked can it be replace if yes please how

@lukiczwa12 11 ай бұрын

What liquid do you use to remove the glue? Regular lighter fluid? ;)

@ElectronicRepair.Serbia2023 7 ай бұрын

Yes Regular zipo lighter fluid

@Draeber 11 ай бұрын

i added a FHD cable and installed a 1920x1080 screen. totally awesome now, but was more work than i thought it would be. Had to completely disassemble it...

@jdryyz 3 ай бұрын

Hi! I am interested in doing an upgrade to a 1920x1080 panel also. Are you saying the FHD cable added additional steps or something else made it necessary for more disassembly in your case? The panels seem to be easy to locate but the cables not so much. I know you cannot add links to YT comments but maybe you can share where you found yours?

@Carobni.patuljak Жыл бұрын

Višak delova :-)

@fraaggl Жыл бұрын

IT DOESN'T WORK , the only good technique is to change the BMS, cut open the case and change the BMS, it's tedious and takes several hours...

@Krzysix.io11 2 ай бұрын

It works, you're not smart enough

@fraaggl 2 ай бұрын

@@Krzysix.io11 I've tried on several batteries and no it doesn't work at all.

@Krzysix.io11 2 ай бұрын

@fraaggl give me your discord ill help ya out

@Krzysix.io11 2 ай бұрын

@fraaggl give me your discord I'll help ya out

@Krzysix.io11 2 ай бұрын

Give me your discord I'll help ya out

@fraaggl Жыл бұрын

Pas la peine de vous fatiguer CA NE MARCHE PAS !! Il faut la bonne commande BUS, meme un bypass sur un mosfet ne marche pas du tout. La seule technique qui marche c'est malheureusement de changer le BMS ce qui prend plusieurs heures vu qu'il faut carrément couper la coque alu a la meuleuse...