MrAmorti

Пікірлер

@bernhardprumm1168 4 күн бұрын

Hey, I am struggling with the doors, I have an issue while opening the doors via rc, one door doesn't open properly, goes up sticks and falls down, it seems as is there to less traction, with manual help it works. Any idea? Thx

@MrAmorti 4 күн бұрын

@@bernhardprumm1168 somebody else had this problem. It turns out CaDA gives you two strong clutch gears for the doors, and a weaker one for the spoiler. Maybe like him, you put a weaker one in the door?

@bernhardprumm1168 4 күн бұрын

@MrAmorti boah, quite fast. To be honest I can't see it without deconstruct, but many thx, I will keep in mind for Some cold winterdays

@plavnieks66 Ай бұрын

you fixed it?

@MrAmorti Ай бұрын

Yes. Yamaha fitted a new TPS under warranty, free of charge! Crazy on a 20 years old bike, but true.

@plavnieks66 Ай бұрын

Thanks, have the same exact issue 👍

@MrAmorti Ай бұрын

@@plavnieks66 no harm in asking Yamaha to fix it. Email the local dealer with your chassis number, and ask them if the recall is still active for your machine. Not sure if it's country dependent, but I think it applied for all S1 models at least.

@MrAmorti Ай бұрын

@@plavnieks66 if they won't do it FOC, don't bother replacing it with a new one off uncle Ali. Better off with a used S2 , or a new original part.

@쿵똥똥 Ай бұрын

When moving forward using the pullback motor, the gear works well, but when moving the pullback motor backward, one of the gears does not move and makes a clicking sound. I would appreciate it if you could tell me how to solve it.

@MrAmorti Ай бұрын

@@쿵똥똥 watch the video! It's all there for you.

@쿵똥똥 Ай бұрын

@@MrAmorti Does this mean that if I change to the yellow gear knob, the pullback motor will work well!?

@쿵똥똥 Ай бұрын

@@MrAmorti kzbin.info26ur3Y28iJE

@쿵똥똥 Ай бұрын

kzbin.info26ur3Y28iJE

@MrAmorti Ай бұрын

@@쿵똥똥 yes. However it is still not like a real RC car. It will destroy other parts if you do lots of backwards and forwards movement

@JuanJoséMolinaRios-n6y Ай бұрын

How did you do that?

@MrAmorti Ай бұрын

The problem was the pivot bolt. BMW used a 5mm thread with a 6mm shoulder, and there's no bush in the lever. It's no good, and after some time the hole wears too big, and it gets stiff. I drilled the lever out to 8mm, threaded the holder to M8, and used a stainless bolt as the pivot. More here revtothelimit.co.uk/viewtopic.php?t=6618

@MrAmorti Ай бұрын

@@JuanJoséMolinaRios-n6y kzbin.info/www/bejne/r6G8dYaQp8lqhbssi=aFDhmw5neaOrdAh4

@nejadsb 2 ай бұрын

Any tips for fixing the steering angle? It has very poor steering in 4wd build

@MrAmorti 2 ай бұрын

@@nejadsb build it in two wheel drive. The manual doesn't hide the fact it has poor angle in 4wd mode. It's because CV joints aren't strong enough for the weight and power, past a certain angle.

@MrAmorti 2 ай бұрын

@@nejadsb also there's no central differential, so driving it in 4wd isn't really a great idea.

@bettinaschneider1316 2 ай бұрын

Thanks, I will get my one next days

@rescobar1907 2 ай бұрын

Hi Amorti. Thank you for the video. I have completed the product. The doors and spoiler work very well. I have no problems going forward. My only problem is going backwards. It gets stuck when going backwards. What should I pay attention to? Can you please help?

@shinji6645 3 ай бұрын

Do you maybe have a fix for the spoiler getting stuck, not wanting to retract and not extending all the way? It's making me go fucking insane

@MrAmorti 3 ай бұрын

@@shinji6645 I've not encountered that. Maybe the clutch gear is weak or an actuator faulty? You'd have to identify the issue before you could solve it.

@shinji6645 3 ай бұрын

@@MrAmorti I think the cog has too much resistance on it as the motor makes the axle spin but it just doesn’t grip onto the cog. When extending it stops halfway through because the motor faces too much resistance. I just have no idea what to change to make it stop shitting the bed in that case, I built it entirely by the book :/ Good job Cada, definitely worth almost 300€

@lienly 4 ай бұрын

kzbin.info/www/bejne/mZqWfH-IdrSsp9E though I don't understand what he says, from video you can see his car doors open and rear spoiler up simultaneously.

@lienly 4 ай бұрын

watched this video 3 more times, found few more questions. decided to upgrade suspensions together. at 19:29+22:21, can't find that green shock absorber c51021 on cada. at 17:36, what's the part number of 'number one connector with 2 stud axle'? at 2:48, what's the 'little cowling little fairing' to press 2 rubber bands? at 7:54, you say don't put a 3 long pin, but put a 2 long pin. does 2 long pin include in package? once I got all needed parts you mentioned, I will start building this AMG ONE. thanks again.

@MrAmorti 4 ай бұрын

@@lienly 1) I have it from an older military motorcycle. 2) it's two parts. An axle and a connector.

@MrAmorti 4 ай бұрын

@@lienly 3) the whole assembly I was holding. 4) there are plenty of spares in the box

@Nebula0825 4 ай бұрын

F***king flaw design

@lienly 4 ай бұрын

So all I need to buy for fixing bugs are just 2 yellow gears? The rest bugs can be fixed by using package parts? Thanks.

@MrAmorti 4 ай бұрын

@@lienly yes, the only real bug I had was those gears. However, you may also want to buy two metal universal joints (four if you're going 4 wheel drive) as one user reported a plastic joint failed. The suspension stuff I mentioned is not really bugs, it's all optional and uses very common parts if you have any kind of spares reserve. If my video helped, please use my affiliate code AMorti5% :)

@lienly 4 ай бұрын

Thanks for your quick reply. Yes, your videos are very helpful. This AMG one is my first MOC toy car, a freshman in MOC. so I don't have any extra parts. Just temporary ignore the suspension issues. What's the metal universal joints part number? I plan to build 4WD. What's the instruction manual step for these joints? Does your promo code apply on parts?

@MrAmorti 4 ай бұрын

@@lienly code applies to the whole cart. Joints are here: decadastore.com/products/cada-metal-universal-joint-3l-jt6001

@lienly 4 ай бұрын

@@MrAmorti check manual, the 4 universal joints are on steps c37, a50, a56.

@MrAmorti 4 ай бұрын

@@lienly the supplied joints are plastic. It's stronger with metal upgrades

@JuliusEngelmann 4 ай бұрын

Do you think that its possible to not have the doors electric, so i can open them separate from each other?

@MrAmorti 4 ай бұрын

@@JuliusEngelmann everything is possible. But! This model was designed from the ground up with the motors in mind. You'd have to figure out the modification yourself and where to put a thumb wheel. Consider the speed of a CaDA motor is faster than a Lego one, but the doors open at a moderate speed. It's going to be a whole lot of thumb turns to make a door open. Better to look for a way to fit two of the micro motors, I think.

@s24667 4 ай бұрын

Guys, quick question. Both of my left wheels, front and back, are not moving. Does anyone have this issue? When I take off the wheels, it works, but with the wheels on, it doesn't. They are not stuck anywhere. This means I can hardly go backwards and can only move forward very slowly. The Battery Box loading 3hours and after 5minutes is it empty?When I reverse it sounds like the gear is out. The engine accelerates but does not move when reversing. But when the tires are off, everything is fine.

@MrAmorti 4 ай бұрын

Put up a video. But in general - it must be the tires are rubbing somewhere.

@Nebula0825 4 ай бұрын

Broken design, motor will damage gears.

@Nebula0825 4 ай бұрын

Let’s sue cada for flaws advertised and defect product.

@gabrieldaun9937 4 ай бұрын

Can I buy them?

@MrAmorti 4 ай бұрын

Yes! Link in the description

@paullondon7728 5 ай бұрын

Good morning again hope your well.Could you please confirm the part number for the 2 gearbox parts i believe it is 32072 ? Also not sure of part number for 2 long pin in same modification Thanks Paul

@lienly 4 ай бұрын

can't find 32072 on cada web... don't know the part number of 2 long pin...

@paullondon7728 5 ай бұрын

Just started building lego technics set's and really enjoying it in your opinion is cada as good .

@MrAmorti 5 ай бұрын

Yes it's good. It's maybe not *as* good in that it's not as thoroughly tested, but it is good. And a lot cheaper. Among Chinese bricks, CaDA is my favourite. Especially in recent sets like this one, the quality is right up there and some parts like tyres are better than Lego. Some other brands like mouldking are good, but the pins are a harder plastic so go in and out harder and tend to creak.

@Shurik_BLR 5 ай бұрын

Большое спасибо вам 👍

@deletedchanneI 6 ай бұрын

12:58 looks like vertical grey arms are touching tires at top position 🤔

@MrAmorti 6 ай бұрын

Folding up the fender does weird things. It may touch at full suspension compression, but not in a normal position.

@deletedchanneI 6 ай бұрын

what do you about this set overall? is it worth it? i’ve found your review, don’t worry

@MrAmorti 6 ай бұрын

I still think it's a great build, and looks good on the shelf.

@mansoorayaz3461 6 ай бұрын

Hi. At what part of the video do I place the T liftsarms? Also where can I buy the number 1 connector with the 2 stud axis from. Could not find it on bricklink

@LittleBuddy_0723 6 ай бұрын

Thanks for the tips👍❤️ Btw I would like to ask, how to remove entire battery hub out of the Mercedes-AMG One in finished build?

@MrAmorti 6 ай бұрын

It's not going to be easy to extract the battery. You can charge it inside the model, so it was never meant to be removed. You'd have to start removing panel assemblies until it fits out.

@LittleBuddy_0723 6 ай бұрын

@@MrAmortiI see, because I scared the battery long time didn't charge or use the liquid will leak out to damaged the AMG one 😬

@MrAmorti 6 ай бұрын

@@LittleBuddy_0723 it contains a lithium battery, it won't ever leak.

@LittleBuddy_0723 6 ай бұрын

@@MrAmorti really?ohh thanks for let me know ❤️

@MultiAndreasH 7 ай бұрын

Du hast mir sehr beim dauen meines AMA One geholfen, ich habe alles aus deinem Upgrade Video umgesetzt und bin Extrem zufrieden.

@adolfshitler 7 ай бұрын

What was the initial problem? My fz6 misfires at times quite badly at small throttle settings when the bikes hot around 3k rpm. Cheers

@MrAmorti 7 ай бұрын

The TPS was bad. Replacing it immediately cured the problem. I have another short showing it in diagnostic mode. I was able to get the TPS paid by warranty/recall , even just this recently. Ask the Yamaha dealer for the same!

@adolfshitler 7 ай бұрын

@@MrAmorti I went to my local Yamaha dealer today, they said no recall for my 57 plate fz6. Funny thing is, before i went i opened the diagnostic menu on the tps setting 16-102 with no fluttering, i gently opened and closed the throttle, turned the bike off and my misfiring has now gone, how strange is that!

@adolfshitler 7 ай бұрын

@@MrAmorti Have been to the Yamaha dealer and they said no recall for my 07 fz6. Before i made the 8 mile journey i entered diagnostics mode and checked tps "16-102" with no glitches, strange thing is that after doing that the poor running/misfiring has now stopped. How strange is that?

@MrAmorti 7 ай бұрын

@@adolfshitler strange for sure. It can be as simple as dirt on the wiper track, maybe you somehow cleaned it off? Or maybe it'll fail again soon, if it's even that. Did you ever catch it glitching? If not, could also be eg. a bad fill of fuel with water in the bottom of the tank that's now worked its way through.

@adolfshitler 7 ай бұрын

@@MrAmorti Very odd, never saw it glitch at all, it's was doing it through many tanks of fuel so unlikely to be water. It would at around 80°c start kangarooing at very small throttle settings every time i rode it for the last 3/4 months 50/60 times, never did it before then. It's only got 9k on it so was hoping for trouble free running for many many miles. My only other thought was a coil breaking down when the engine was hot and transferring heat into them. Time will tell no doubts 👍

@milan6230 7 ай бұрын

hey, my reading says 14, which is below recommended, does this means that tps sensor needs replacement?

@MrAmorti 7 ай бұрын

It probably does! Especially if you're getting running issues. Test it again when hot, look for glitches

@vladhack 7 ай бұрын

Can you please tell me what is the fastest way to rebuild from 2wd to 4wd?

@MrAmorti 7 ай бұрын

Sorry no. It's not something I've done, nor would I recommend it since the steering is *so* limited in that configuration.

@KryptonianCraft 8 ай бұрын

at 17:38 where can I get the number 1 connector with a 2 stud axis?

@MrAmorti 8 ай бұрын

Probably bricklink is best, if you do not already have those as spare parts.

@KryptonianCraft 8 ай бұрын

@@MrAmorti can you please send me the link? Thank you so much.

@KryptonianCraft 8 ай бұрын

Hi. Thank you for sharing these tips and tricks in your build. I watched it couple of times. The 2 yellow knobs need to add in the motor to avoid the skid, are those extra parts in the box? or need to get extra from the Manufacturer?

@MrAmorti 8 ай бұрын

Thanks! Those gears aren't included. You can add them when you order from CaDA, at 6 cent each.

@damararyohanggoro9162 8 ай бұрын

Nice review and fix, cool! Do you plan on adding mudguard on the front?

@MrAmorti 8 ай бұрын

Thanks! You could probably do something using the brake caliper mounting point, but it would probably obstruct the suspension. Unless you 3D print a specific part, I think it is fine without that, but of course YMMV.

@slyght82 8 ай бұрын

Tried everything, but I wasn't able to fix the front suspension. As soon as I attach the hood, it won't push all the way back. Looks to me it's not only related to the electric cables but to the hood on top as well. In addition to that I have issues with the drivers door not opening correctly because the large conrod is dragging on one of the connectors of the steering wheel. Secondly moving backwards in conjunction with steering is not working well. I have not figured out why, but I guess it's related to the overall weight of the model because it works perfectly fine when I put the model upside down. In case you have any hints, how to fix that, please let me know.

@riccardocosta2767 8 ай бұрын

Hi, what tipe of lamp (the code) did you punt on the front light? Thanks

@MrAmorti 8 ай бұрын

It's a used OEM indicator from BMW. Sorry, IDK the code.

@mssm9495 9 ай бұрын

But after 5 mins of play, the car will no longer drive in reverse. There's a clicking noise from somewhere that is NOT the knobbly gears (as per the fix), nor the pull-back motor. The clicking is from somewhere just behind those elements or behind the central diff.

@mssm9495 9 ай бұрын

And now because I was forcing the issue, the car doesn't drive forward either. The same gear pairing is now constantly slipping. It's most likely related to the rear wheel dif maybe.

@mssm9495 9 ай бұрын

It's the differential that's slipping, because the fake engine is running OK. One of the new Lego differentials should fix it.

@MrAmorti 9 ай бұрын

@@mssm9495 sorry it happened to you! The car is quite big and heavy for the old type differential, so it can be better with the differential type from the TopGear rally car or even the 1:8 Ferrari. I didn't have any problems, but I guess driving mostly forwards (even up a hill and for a long time) is less stressful than driving indoors with frequent back-and-forwards manoeuvres.

@mssm9495 9 ай бұрын

Yes, after a few minutes of enthusiastic backwards and forwards play indoors, the diff chewed through the 20 tooth double bevel gear. I built the 2WD version, so that would not have helped.

@MrAmorti 9 ай бұрын

@@mssm9495 come to think of it, the CaDA Ferrari from Bruno did the same for me.

@mssm9495 9 ай бұрын

Brilliant and essential mods. Made sure to incorporate them while building the car. Thanks!

@aFrInaTiOn 9 ай бұрын

For the rubberband fix: The section title says A12, but the shown pages in the video are later steps - so the exchange to the smaller 12T gear is in A12.. just if others are that slow in understanding like I am... :D

@MrAmorti 9 ай бұрын

In case of doubt, go with the PDF version 😊 bricksafe.com/files/A_morti/cada-suzuki-katana/KatanaFixes.pdf

@MultiAndreasH 9 ай бұрын

Herzlichen Dank dafür….

@MrAmorti 4 ай бұрын

Bitte sehr!

@MultiAndreasH 9 ай бұрын

Herzlichen Dank dafür….

@theblower069 9 ай бұрын

i`m getting this on monday and just watched your video. A big thank you for the tips i wont be able to swap the suspension springs but with the cable and the arms that should be ok to do. As for the other tips i`ll be doing them. Once again a big thank you. Still a very good model Cada have one up`d Lego with this. Cant wait to get it.

@tren133 10 ай бұрын

What a comprehensive video! I haven't even decided whether to buy this kit yet, but ordered 15 black T-liftarms just in case LOL. Regarding the shocks, do you know if there is a Lego equivalent which is also firmer? Looking on bricklink, Shock Absorber 9.5L (hard spring) - 2909c02 looks identical to this spring.

@MrAmorti 10 ай бұрын

I'd say that the Lego spring is pretty similar to what you get with the kit. Tbh the original shocks aren't bad at all, I just was fortunate to have harder ones available.

@lienly 4 ай бұрын

can't find you mentioned 2909c02 on bricklink...

@tren133 4 ай бұрын

@@lienly That's weird, it comes up for my on bricklink, as Technic, Shock Absorber 9.5L (hard spring). There is also an "extra hard spring" version, 95292c01

@colinbrown2225 10 ай бұрын

Hi i just woundering for any help here just got this set now i have to parts misssing from bag 4 2 R15 and 2 L16 have contacted seller a week ago now no feedback yet uk seller is there any where i can get these parts thx

@MrAmorti 10 ай бұрын

service.decadastore.com/ Try CaDA directly, hopefully they can help!

@pdh7722 11 ай бұрын

Dpo you know if they will they be making one without the motor/remote controls?

@MrAmorti 11 ай бұрын

I don't know, better ask directly

@ethanzaiden365 11 ай бұрын

I just completed all the drive components and started test driving the set around the house. Im hearing a sudden click noise coming from around the rear of the car when using both motors forward from a complete stop. Once the set starts going the clicking stops. Im not sure if this is the gears in the dif clicking or the motors themselves. Do you have any idea what could be causing this? And if you do, is that damaging the set? Sorry for using you as sort of tech support, but you seem very knowledgeable about this set and would appriciate the help to make sure mine is working the way its supposed to be 😅

@MrAmorti 11 ай бұрын

Hard to know without seeing it, but the only gears which aren't fully braced on both sides, are those bevel gears. Flip the car upside down, put some resistance on the tyres, and try to replicate the fault. Probably it'll be the bevel gears.

@ethanzaiden365 11 ай бұрын

Looks like its the rear differential itself slipping against the drive gear :/ Idk how to fix it bc the differential is gonna be a huge pain in the butt to remove. If this keeps on happening, will the gears on the diff eventually just wear out and stop working?

@MrAmorti 11 ай бұрын

@@ethanzaiden365 that's unfortunate because you're right, it won't be easy to get into that 5*7 frame. Maybe get hold of a heavy duty differential from the Lego Ferrari, and fit it whenever the gears quit engaging?

@ethanzaiden365 11 ай бұрын

So i just got the set and came across the video, for the clicking gears, is this an issue that can happen through normal play or is it something that happens if you try to stress the gears intentionally? I havent finished building the set but it looks like in your demonstration that the clicking gears occur when purposefully trying to break them. Is this problem a super critical issue that needs to be fixed? I dont have the replacement gears on hand and was wondering if i should just wait on continuing to build the set until i can get the replacement gears

@MrAmorti 11 ай бұрын

IMO You should continue building. I think that if you never run the two motors in opposite directions to charge the pullback quicker and also let it hit the end, you'll probably never have the fault occur. If on the other hand that does happen once, I believe the click will then always be there. If it does happen you can just get the gears for a few cents each, cut that one pin, and do the mod.

@LeGeek88 11 ай бұрын

Bonjour, Alors moi j'ai fini de monter ce modèle, sauf que je trouve que semblant des disques de frein font freiner les roues avez vous ce même soucis. Par contre j'ai bien pris en compte les 2 pièces knob jaune Merci

@MrAmorti 11 ай бұрын

The brake discs shouldn't interfere with the running. If they do interfere, then maybe something must be adjusted.

@aFrInaTiOn 11 ай бұрын

Thanks for the nice and detailed review! Looking good and seems to be a nice set - except if one is concerned about the engine.. :D

@maweb_ Жыл бұрын

Hi there, I need your help. I'm currently stuck at the doors.. I can open the door but it won't close. It seems that the button for closing the of the remote control has no function. Opening is no problem. I also saw how the spoiler at the rear was moving in. But now it's not moving out.. I checked the cabling and everything seems fine. Every other button on the remote controller works. But not the one for closing the doors.. any hints?

@MrAmorti Жыл бұрын

Could you have a faulty remote? Try connecting the motor to a different output in the battery, and see if it works there. Try posting a video at the CaDA Bricks Facebook group, maybe we the community can help, or point you where you can get replacement parts if faulty.

@maweb_ Жыл бұрын

Thanks, will check this out!@@MrAmorti

@staenker1983 Жыл бұрын

Love how your doggy is entering the room and looking like “I was sleeping… WTF are you doing again!?”

@OfficialTransformers Жыл бұрын

⚡️⚡️GREAT STUFF⚡️⚡️I’m glad I found your channel I look forward to seeing more of your videos📺 I do mostly TRANSFORMER Stop Motion 🎬📸🎞️ I hope you enjoy my animation‼️ 5:46

@FlamboyanToPossuM Жыл бұрын

I'm just so happy that CADA is coming up in the world! They've been doing a great job making custom models and I'm glad they've been getting recognized by manufacturers. CADA and COBI coming into their own and doing licensed sets is great to see and I'm all too happy to see real competitors to Lego :)

@Nebula0825 4 ай бұрын

This model is a f@@@@king flaw design….Lol

Ең жақсы KZbin

Пікірлер