2 жыл бұрын
3 жыл бұрын
3 жыл бұрын
4 жыл бұрын
4 жыл бұрын
4 жыл бұрын
5 жыл бұрын
5 жыл бұрын
6 жыл бұрын
6 жыл бұрын
9 жыл бұрын
Пікірлер
@Repny2dafullest813 Жыл бұрын
The question I have is you mentioned "that one doesn't count." Why doesn't it count if the piston is all the way up.? I think I might have put my timing on that one. I rebuildt the engine and put it in and obviously doesn't turn on
@JoeGormican Жыл бұрын
It has to be on the compression stroke. Remember on a 4 stroke the piston will reach tdc 2x for each explosion. You can plug the hole a bit until you feel it pushing air out. That's the compression stroke for timing the cams.
@pranksnstuff Жыл бұрын
Great video. How’d you Mount your dial indicator? Seems like a great way to do it. I was about to try with wooden dowels but this seems much more accurate
@JoeGormican Жыл бұрын
I don't remember. Maybe there was something magnetic or maybe i just set it on something.
@JoeGormican Жыл бұрын
I abandon this setup last year. It was nothing but trouble. I had so many hours of tech support trying to see why it would do stupid things like reset the Z height to -50 and try to drive the torch through the table while ignoring the touch and lift sensors. Or randomly firing the torch during rapids. I went to a CandCNC and it's much better!
@greggjarvis133 Жыл бұрын
Like what was even the point of that?
@JoeGormican Жыл бұрын
Like why did you even watch it? If you need to time the cams on the mr1 it might help. Otherwise it doesn't apply.
@HITCH13 2 жыл бұрын
I'm curious on how the cam chain goes on exactly. I was told there is a certain way the chain goes on
@JoeGormican Жыл бұрын
Not sure but it seems like it can only go one way
@HITCH13 2 жыл бұрын
Where are you located?
@wifigoss 3 жыл бұрын
I spent a month trying to figure out issues with my c79 so did a friend of mine we discovered the boards were bad. Yours is to I know this because of the led lights on your inputs The five led lights on the inputs should not be on with nothing connected. I purchased four C79 from CNC4PC and he finally sent me two good ones with added resistors on the back to fix the issue. Just letting you know.
@JoeGormican 3 жыл бұрын
Thank you for the tip!
@joeymccaughan3656 4 жыл бұрын
hi joe how have you found the tmc torch height control?
@henryclark522 4 жыл бұрын
How were you able to surf with.no ballast or anything? I have a 2019 212 limited s and want to surf as well, any tips? Thanks.
@JoeGormican 4 жыл бұрын
Just practice keeping the nose as close to the water as comfortable. Try giving yourself a tug into the wave and ride it in. Stay within 2' of the boat. Technique plays a big part. If you're losing the wave have the driver slow. If the wave breaks have the driver speed up.
@michaelcawcutt5980 4 жыл бұрын
We have an 18 212 LTS - I'm able to do what Joe is doing above - touch n go with the rope. We JUST got the wake-booster. Definitely cleans up the wake and gives it a little more push - hoping to have it "dialed in" soon!
@michaelcawcutt5980 4 жыл бұрын
@@JoeGormican What speed you running? On our 18 212 LTS we run 10/11 mph (4600 rpm)
@jay19dbfl 4 жыл бұрын
Look at jetboatpilot. They have the setups dialed in as far as where to put the ballast to make the best wave
@GDFred88 4 жыл бұрын
Where is video "Part 1"??? I think I have the same problem. But I would like to see how far off your marks of when off by one tooth.....
@JoeGormican 4 жыл бұрын
Not much, maybe 1/8" from the mark.
@andredesouza9767 2 жыл бұрын
That's my problem right there 1/8 :(
@mchiappinam 2 жыл бұрын
@@andredesouza9767 Did you got 0psi of compression with that?
@justingeturgun 5 жыл бұрын
Doesn’t matter what side is at top dead since both outside pistons move relative to each other. I just. Put it at top dead. Move the cams to marks. Then tighten down the caps and install tensionor and it’s golden everytime.