The only problem with this is the smell from the drains are free to come up through the drain as there is no trap to stop it. You need to put a trap to stop this.

Iv just painted my floor with polyurethane paint about 4 days ago does it go hard or stay soft like rubber if so is there anything I could paint over it to make it a hard surface as I’m putting my bikes on Stands on it thanks

Thank you for posting that. Perfect idea for a skim over my sound but unsightly concrete driveway.

Great video just did my radiator and bath

Your hands ain't showing, ain't seeing what you doing

Great job... Nice colour... would that work over a fake wood work door?

Very good level witch is the most importent thing. If the level aint right the dont matter how good you lay the slab, its a shit job

Never put cross joints and never have more then 1800 mm joints

😮 OMG

Every single thing he’s showing you is wrong

It’s a case of if it doesn’t move silicon it you don’t need silicon render stainless steel bowl not if it’s fixed properly what a mess

Thanks man

Try to stop back smell?

On ne voit pas comme tu as fait

European regulations require cables to be run through conduits. By burying the cables directly into the wall, it will be impossible to pull a cable if a fault occurs in the future, necessitating the chasing of the wall again. Additionally, using an extension plug instead of installing a wall socket is completely unacceptable. This doesn't look like a proper job, mate. To be honest, more like a bodge job!

Great video! Done the same myself now - thanks for the tips! Appreciate it

How’d it hold up?

Great content matey

This was a great help. I’m a carpenter over 50 years and now retired. I’ve done quite serious work in the wet trades with acceptable results. Always looking for techniques with the wet trades and you’ve given me some more! Thank you. Love the fibre mix and the admixture tips, especially for external patches like these. I bought a poker for pouring my basement walls and worked out great. I just wondered if you’d perhaps use some form of vibration in placing your patch here, not overly much but some to consolidate? Obviously not a 2” poker but what I don’t know.

Thank you so much for this very clear video. I followed along to shorten the blinds I bought with tapes, and I couldn't be happier with the result.

Where can i buy one?

Not helpful, I can't see what you are doing, Bad work

Why do you use your finger instead of a spatula? I'm asking because I want to do it in my kitchen, but I'm afraid it won't look good if I do it with my finger. Thank you in advance for your response.

PVA really helps prior to plastering otherwise wall sucks the moisture out of the new plaster and you get cracks like that. I must admit I try not to use an angle grinder (tempting though it is) as it takes days to get all the dust out the room plus tight fitting mask rather than cheap paper ones a must. Hammer and bolster definately more hard work but less fine dust.

Eso es Marte nooo?

Useless use,a auger drill bit

Hi can I askvwhy you wet slabs first, isnt it more difficult to brush compound when wet rather than dry

Just moved into my first house, going to be laying my laminate this week, pulled off my skirting to see big holes already done by the previous owners and just covered up, looking forwards to giving this a go and getting it sorted before my lovely new flooring goes down. Thanks for the great vid.

I’ve just painted mine Matt black all purpose universal but how long should I wait until I turn heating on?

I’m only replacing my skirting boards not the flooring is there any way to fill in the gaps while protecting the wooden floor that’s in the room currently?

Iam sorry but we can't see

How to mic

I cant see anything. Terrible

You don’t need to sand / just get a bucket of hot water and dish soap the door clean and buy a can of self primer and 2 cans of the finished colour / and take out the windows / it took me a day and it looked great and 6 years down the road it’s still faultless

Really informative video. Thanks for that. Just followed your instructions and replaced a rotted door jamb in the cellar. It had been nailed on with giant Victorian brad things, but the new one has five concrete easy drive screws holding it. It isn't plumb, but neither is the rest of the house. Place looks like they used a cat on the end of a length of rope as a line.

Is there no need to use PVA before you apply that One Coat?

This was really helpful, thank you! In my case the plasterer filled up the holes, but I plan on putting a smaller skirting board than it was before and not sure how to make it look nice 😮‍💨

Poo camera work. Didn’t show how you fixed the sockets into the wall

What’s the fall towards the ACO from the building? Lovely looking job

Nice finish!! what’s the fall from the building for water run off, I’m setting out my paths and concerned I’ve not left a good enough fall. I’ve got 10mm of a fall over 1800

Is the primer just concrete glue? What is the fiber has to do with bonding? You need to vibrate the new concrete for a better surface to surface adhesion.

This is just gross

You are a joke. Nobody taught you pride. 😢

This is really helpful! Pulled off my skirting yesterday and faced this exact situation!

Great vid. Qq- could i just spray the whole radiator rather than brush painting?

This is good useful video but some important parts & step are not showing due to camera angel

Right my project for June!

In terms of regs, can drainage channel be plumbed into the rainwater pipe, or does it have to go to the waste pipe?

I know you were trying to help out but jeeezus,..couldn't see a damn thing due to the shoddy camera work.

And I’m over here wanting to chase the block work because it pisses me off to no end when it sticks out on the wall too