So, if I use the LC7i just like you did, I don't need the PAC AMP Pro AP4CH1 like everyone on the 5th Gen forum is using? And I'm not sure why I others use both. I have a 2019 RAM 1500 with the base stereo as well. I am confused if I need the PAC AMP Pro AP4-CH1 and the LC7i so I don't lose anything or if the LC7i will be good enough alone. I already got the aftermarket ANC bypass. Did you lose alerts or useability in anything? Aside from ANC.

I wonder could these fit in the fourth Gen’s?

I've had 2 Corsa's in the past. I have a Borla sport on my Ram. The Borla is definitely deeper. I have a Corsa sport middle exit coming for my F150 tomorrow.

Thanks for the install tips. I have the same truck with the same shroud as your father. What kit or model do I need to buy for my ram 1500 Limited? Thanks for your assistance in this matter!

So you only ran two rca outputs from the lc7 to the amp? To be able to adjust them and wires the sub from the amp only correct? Dont need a separate channel rca for the sub? If so, could i get away with an lc2i instead ?

Man that’s some great lighting!

Hey quick question I have 2016 cla250 the head unit is not screen touch so how would I make this box work on my car since there is a lot of screen touching going on please let me know thanks

Nice video. Glad we could help you get squared away! For those curious... when you order the fog kit we'll provide the correct harness for your lights. Waterfowler 41 already had lights he was using which is why he had to change out the pins on his wires. BUT when you order our complete kit, we give you the right harnesses for the lights. Also, the bag of wires, that's our upfitter extension kit. That's not required and is an optional component. On the Raptors Ford makes the wires a bit short so this extends them which makes adding accessories later REALLY EASY!

Bought these Smartliners for my Chevy Equinox, fit like a glove awesome!

You really do not need to remove the screws…just loosen them enough to allow the lip of the liner to be inserted. The instructions really are terrible. It was a 60 minute project I cranked out this afternoon on my 24 Raptor.

I made an upgrade to this kit and Packbrake was gracious enough to provide me with the fittings I replaced the 90 degree fittings with 45 degree nipples on both for best oil flow I was told 90 degree fittings will greatly reduce oil flow.

I want to get this rack, but.... with removal of the gutter trim, does it leak water into the exposed clips since the trim piece wasn't put back in..

That’s amazing, is it possible to do it by programming using obd ?

I'm a chevy/gmc guy. but this truck is bad effing a$$! love it.

What’s the feel of the mats? I have an issue with stuff sliding around on my rear seat mats that came with my truck. Trying to find something like this that has a little more grip on top of the mats.

I bet your kiddo loves that truck! My sons love my RAM and call it a mini monster truck. 😂

I went with the Borla ATAK on my 2023 Ram 1500 built to serve edition in Hydra Blue. Love the exhaust! It makes a deep throaty sound--not too loud, not too quiet. I also got a 3-1/2" lift and 35" tires. Truck looks and sounds great.

Hello, I was analyzed your YT channel and I saw that in your channel have some problems, that's why your channel is not growing. Your videos is not reaching to targeted people, not getting engagement. Do you want to know these problems? If you can give me permission I can tell here, . Where Can I tell? here or email?|||\\?|?|/

Could you clarify if this pipe is intended solely for the factory location intercooler, or if it can also be compatible with the Cobb FMIC?

Look at big money over here

The vans all have built in locations for mounting things. Even SUVs commonly have rack mount. I wonder why trucks don't?

Vice design makes a cool bracket that uses pre existing mounting points where it sits just under the shifter knob.

Only issue is the clear coat on carbon fiber usually fails early and turns yellow. Ask me how I know. Make sure you keep your oe trim.

Awesome 👏 thanks man

Can you increase the RPM idle for when your going to be sitting for a while?

Nice video, I did the same mod a few weeks ago and it was annoying that there were no instructions. Turbos are definitely louder now. I can't comment on performance of this alone because I did intercooler, turbo Inlets, lower temp thermostat and down pipes all at the same time. What I can say is the mid range is definitely more punchy from all the mods. I'll be going to MPT soon for full E85 tune, injector and pcm swap (I'm 2023 also) stay tuned.

Yo that’s a cool metal pipe and a blinker fluid restricted delete paired with a nitro boost

CLANG CLANG CLANG

parking mode?

Nice video. How is the topper holding up?

how the steering wheel do with oil from you hand do you have to clean it alot? Also i thinking about a copy the same one you did. compair to the rebel that was gloss

I really like your video. And I have a same Rebel as yours. I do want to buy that bracket, but the link doesn't work, can you help me?

What weather strip did you use along the piller to hide the wire

Do you experience water coming from the talegate?😊

💯🔥

Looks great

How quickly can you remove it? I don’t plan on running it all the time, just when camping and I need the kit my kayaks on it.

What about fluid retention for like spilled drinks or something? That is my biggest concern going to these over weather tech. The grommets for the posts have holes in the tops that fluid could run down in and the mats themselves seemed to drop off, like in the front of the rear seat mats and at the doors, which would let fluid run off the mat into the vehicle. Have you tested the fluid retention or had any spills to see how that works yet?

Thank you for this video. I will be going this route. Where can I find t-slot inserts to install some chase lights? I would like to mount a couple BD S2s or DD SS2s. Thanks in advance!

Since you left the RAM cover on, how has been running?

What did you use to poke a hole on the rubber grommet to run the positive ground wire? Did you have to use a drill bit or is it easy enough to poke a hole by using a philips scew driver?

Do you know if that rear mat will work if I have the rough country under seat storage instead of the factory one

Not good State with hot Summer. The cover material gonna shrink and pull off both sides of the rails and at the back of bed cover 2 1/2 years later. The aluminum gets so hot, no glue can’t bond for long.

Not good State with hot Summer. The cover material gonna shrink and pull off both sides of the rails and at the back of bed cover 2 1/2 years later. The aluminum gets so hot, no glue can’t bond for long.

I hope by now you have purchased one of those nutcert installer tools from HF. 😊 Great video. I'll subscribe just to see what you're up to.

I have a 08 tundra and live in Southern New mexico. I have been running toyo open country for most of its life. Great tire only got better with the at3. It's the price that sucks.

Those won’t tie down a bundle of 2x’s. The eyes down near the floor are the most useful anchors. Straps run nearly horizontal don’t hold down much. The steeper the strap angle the more downforce

What mount is that for your phone?

Instead of slicing the back stake pocket would it work to go at it with a router bit? I wonder if you can retain the top piece of plastic but just remove the drop?