Does the old bushing stay out the housing when driving the new one in ? Sorry having trouble understanding the bushing install part
@waterfowlhunter1002 ай бұрын
Yes, just tap the new one in. The old one does not stay on
@ISAACIIV5 ай бұрын
What is the name of that tool?
@waterfowlhunter1002 ай бұрын
Seal puller
@joeroid12058 ай бұрын
Its was leaking alot fliud?
@waterfowlhunter1008 ай бұрын
Yes
@primerecovery51739 ай бұрын
How did you know the bushing was bad? Thanks
@waterfowlhunter1009 ай бұрын
Leaking transmission fluid
@Nebulous0_o Жыл бұрын
Genius idea driving in that new bushing with the old shaft👍🏻
@boomergt1 Жыл бұрын
Did you use a kit?
@waterfowlhunter100 Жыл бұрын
No, just got the bushing itself from the local dealer, it's still holding up. I've drove it roughly 20k miles and have no leaks.
@474outdoorz7 Жыл бұрын
Like the video. Got one made up similar to it. How did you wire it up?
@waterfowlhunter100 Жыл бұрын
Just wired a toggle to it I run into my ground blind.
@toddbob552 жыл бұрын
Chryslers have been garbage since the beginning of time
@aeron1592 жыл бұрын
if this is the case then, wont the vehicle have a bad misfire all the time?? mine has a misfire on 2 cylinder that will not go away even though I've repld the plugs and coils... but it doesn't idle rough all the time...ima try replacing the injectors next
@waterfowlhunter1002 жыл бұрын
Yes it will miss fire all the time.
@Carlos-ip2ir3 жыл бұрын
Please tell me you did not take off the cam to replace the rocker arm
@plips20024 жыл бұрын
My '05 Avalanche is doing the same thing, I'm leaning towards the transfer case control module, just fyi
@bishop51663 жыл бұрын
That's what it is
@bishop51663 жыл бұрын
Mine is doing that same thing. I had to take the encoder motor off. . put a pair of vise grips on the bitch to get the transfer case out of neutral.
@bengieandnuny5 жыл бұрын
Did the selector case module work ? Was it that or ?
@waterfowlhunter1005 жыл бұрын
I cleaned it, it did the same thing after a while, I sold the truck.
@bengieandnuny5 жыл бұрын
@@waterfowlhunter100 thanks and ya I might do the same
@thegodfaher815 жыл бұрын
How was the compression. Before I got misfire on my truck 2002 dodge ram1500.
@MrShrabber6 жыл бұрын
compression test is bliss
@suckthis16846 жыл бұрын
Hey thanks for the video. I have a 07' Ram with a 4.7 same ticking noise a it sputters when I floor it.
@rayb22506 жыл бұрын
Check the lifter, i just found the same thing on my 2000 Durango. Put it back together, rocker came right off. Lifter collapsed. Bought a new lifter, 9 bucks at AutoZone, got it in, used many handy dandy New spring installer rocker tool, yes, when mine came off the keepers on the valve came off also, had to buy new keepers, put air pressure on the cylinder, put it all back together, no more problems.
@husq486 жыл бұрын
I have an 04 Ram 1500 4.7, it was losing power at 2,500 rpm's and up, recently it started running really rough at any rpm, misfires and a lot of noise. One mechanic seems to think the timing chain jumped a tooth, very hard to start now as well, but I wonder if this could be the same problem...?
@waterfowlhunter1006 жыл бұрын
husq48 it's a possibility.
@TortureBot8 жыл бұрын
Darn. I hope when I replace my injector that that is my problem on my 4.7 in my 2004 Durango. I have had a cylinder 4 misfire for about a month, and replacing all the plugs and then swapping the coil pack with another cylinder didn't change anything. I also used a multimeter to check all the coil packs while I had them all removed. They all tested perfect. Still a cylinder 4 misfire. About to remove the injectors from the left side of the engine and test that one from cylinder 4 and see if replacing it will take care of the problem. If not I may end up having to look and see if I have the same problem that you had.
@robbiebobbie20118 жыл бұрын
my step son's truck run good but it misses when u put in gear/give it gas other wise runs fine. When I had injectors out the intake valve n top of piston had carbon build up I guess maybe valve seal bad
@robbiebobbie20118 жыл бұрын
michael what did you pick up....rocker arm? Did the cam come out without taking the sprocket off?
@katiegroom32408 жыл бұрын
how long does the battery last?
@waterfowlhunter1008 жыл бұрын
few hours, turn it off when no birds are flying
@jimmyferguson33429 жыл бұрын
Yes, but it came back out so I think a push rod might be bent or something
@michaelforshee71579 жыл бұрын
2005 Dodge Ram 1500 4.7 here - same thing but on cylinder 8 - simply picked it up - pushed the spring down and slid it back into place and bingo. Problem solved!
@yaseryousef1407 жыл бұрын
michael forshee I just did the same and I found the 2 arms were down,one of them was broken down there on surrender number 4 because of the lifter was jammed so I changed the 8 lifters on the same side and the broken arm rocker...i got( the check engine light and check head gasket light) both of lights are gone! Drive perfect!!! trans out all (Dodge+jeep) engines of 4.7 having the same problem Thank you for the video, $1500 didn't go West on a mechanic....
@hxrxld9 жыл бұрын
Did you get it done finally?
@waterfowlhunter1009 жыл бұрын
There were 8 lifters that were bad, replaced l of them in the motor, now it runs great
@michaelmeracle46509 жыл бұрын
@drewames58669 жыл бұрын
How did you end up mounting your decoys? Just seen the system and threw one together using a window motor today.. First test had trouble getting them in a good flight direction. With a little more trial and error i could probably line them out but just curious??
@jimmy31539 жыл бұрын
all i did was cut 2 '' off the factory poles and welded them on to the end of the rod at a slight inward angle, that way it levels them out when it turns on