Пікірлер
@ronm6585 6 ай бұрын
Thank you.
@CyberPhox-c3y 11 ай бұрын
Fellow Canadian on the east coast here - nice to see an install like mine that I am planning that can survive the winters up here!
@timpeterson2738 Жыл бұрын
Your video is one of the best out there, good job, and yes I'm copying your install best i can with time being the fear factor.
@Chase_Anderson Жыл бұрын
Thanks Tim! Good luck and any questions let me or the discord community know! The discord chat was super helpful with my questions along the way.
@timpeterson2738 Жыл бұрын
@@Chase_Anderson cool thanks
@atomicdetailsoc Жыл бұрын
i more secure joint would be a heatshrink butt splice connector. you need a crimping tool though...
@Chase_Anderson Жыл бұрын
There is probably always a more secure option… there is no physical loading on this setup and no issues so far.
@_tim Жыл бұрын
Man every time I think I'm settled on pixel strings I see a video like this in my feed that makes me think twice about strips and aluminium channel instead. Looks great!
@Chase_Anderson Жыл бұрын
Thanks! There are pros and cons to both setups. A lot of advocates for pixel strings seem to needlessly really hate on strips, but they don’t mention how expensive perma track is, how long it takes and tedious it is to make your own product comparable to permatrack, or the pain and suffering of pushing all the pixels into the track lol. I personally like the clean look of the strip install, basically invisible when off. And even it also has the option to look very much like pixels too, you could set a segment to use only every 3rd light and it would have the same spacing but still be invisible when off. Both are good choices, and just to make it harder don’t forget to check out the 30mm pucks! They come wired into tracks already, I would do that over pixels.
@_tim Жыл бұрын
@@Chase_Anderson Oh no don't give me a third option! I think my shunning of strips in the past was because I was only considering 5v varieties and getting put off by the more frequent voltage drop, but your video is the first I've seen that uses WS2815 12V which has totally changed my thoughts. Am I right in thinking the backup data line just gets wired into the same data channel output on the DigQuad?
@Chase_Anderson Жыл бұрын
@@_tim that’s what I had thought too, but Quindor (who makes the boards) directly advised me to wire it to ground - so that’s what I did. Further discussion in the community makes it sound like either will work (can splice the data or wire to ground) but I just followed Quindors advice and have had no issues to date.
@timneal609 Жыл бұрын
I want to do strips but how do they do in the extreme Alberta Canada cold winters.
@Chase_Anderson Жыл бұрын
@@timneal609 I’m actually in Alberta, and I just took some footage, I was going to show them working fine in -33C! I’ll make and post that video in the next couple weeks.
@nyacoustics8373 2 жыл бұрын
How do you measure your roof lines?;. Do you actually go on on the upper level of the roof ? Is there a program
@Chase_Anderson 2 жыл бұрын
Yes I went up and measured, being a solo project I taped one end of the measuring tape to the end to hold it lol. For rough measurements you could use an app like measure on iPhone (I’m sure android has something similar) but for the actual measurements for cutting and whatnot I would want a physical measurement. Keep in mind you’ll need to install them, so you’ll need to figure out access at some point.
@nyacoustics8373 2 жыл бұрын
@@Chase_Anderson gotcha thanks so much !
@smattt 2 жыл бұрын
"I'm not gonna climb up on the roof cos I don't wanna die today!" LOL!
@PeteyPablo408 2 жыл бұрын
Do you have a link to those light switch covers? I could really use a couple of those for my flood light security cameras kids tend to turn off too often .
@Chase_Anderson 2 жыл бұрын
Here is the link. I don’t have a 3D printer, I found someone on a marketplace type site that printed 3 of them for $10. www.thingiverse.com/thing:4143224
@PeteyPablo408 2 жыл бұрын
@@Chase_Anderson thanks
@ericmoreno655 2 жыл бұрын
How did u wire up the led lights to the dig quad cause the led strips have 4 wires coming out ?
@Chase_Anderson 2 жыл бұрын
I’m not sure which you’re asking, but The ws2815 are 4 pin which are positive, negative, data and backup data. There are 4 x connect wires coming out of the box which are 1) first strip 2) second strip 3) power only to feed dig uno on second level which controls third strip 4) was going to be power injection for the first long strip but it looked good without it so I didn’t waste my time.
@ericmoreno655 2 жыл бұрын
@@Chase_Anderson thanks I was asking about the 4 pin wires that come out of the led lights them selfs. Since you only need to connect the 12v, negative, and data to the dig quad. But the led strip has 4 pin wires coming out of them.
@Chase_Anderson 2 жыл бұрын
@@ericmoreno655 ok ya, it’s the backup data… major benefit imo to have a backup data line.
@danallen4550 2 жыл бұрын
Thanks so much this is AMAZING information, Did Ray Wu connect the WS2815 strips for you before they sent them?
@Chase_Anderson 2 жыл бұрын
Correct, all I had to do was mount the strips and connect the x-connect ends
@MS-rs8le 2 жыл бұрын
Great video Thanks! Sad that the clips are made from chromed steel and WILL rust over time I am sure of that, may take a few years but here comes the rust??? Wish they made them with stainless steel but cheap china crap right? I would suggest to use stainless screws when attaching ANYTHING outside! Also, ANY led strip that is in a protective silicone sleeve is NOT waterproof by any means! What makes it IP65, 67 etc... is the sleeve itself What people do NOT understand is the condensation factor also. Condensation will in time work its way into the sleeve and the strip will go kaput!!!! This all depends on your weather factors in your region! Im sure using the aluminum channel will help from the elements. Heres one for you, Have you ever asked yourself " WHY " a LED strip manufacturer ONLY puts a 1 year warranty on LEDS they produce when they have a 50,000 hour life span which is roughly 6 years of leaving the lights on non stop! Why only 1 year hmmmm! Hope your project holds up and good Luck Thanks for the great video
@Chase_Anderson 2 жыл бұрын
Thanks. I contacted the supplier and the clips and made of stainless steel.
@JoseHernandez-gl9ef 2 жыл бұрын
What did you spend
@Chase_Anderson 2 жыл бұрын
I think it was around $1000 usd, but that was also buying some stuff like a $200 Makita heat gun lol
@scottadkin541 2 жыл бұрын
You sound like a seasoned electrician. No ones ever gonna see that
@Chase_Anderson 2 жыл бұрын
I’ll take that as a compliment lol
@IntermitTech 2 жыл бұрын
Just stumbled across your video, awesome work on the install but also the video, shows a lot of stuff and how you solved them! Very happy to see the boards are working out for you too. :)
@Chase_Anderson 2 жыл бұрын
Thank you, coming from the master himself that means a lot! You helped me figure out many things in the discord chat, I sincerely appreciate it and the community you have built is amazing.
@mitchyv1980 2 жыл бұрын
My ip65 tape came with adhesive backing. Its worthless. I use construction adhesive to glue them in my channel.
@Chase_Anderson 2 жыл бұрын
That makes me feel better, thanks!
@lucasschrieken 2 жыл бұрын
your video was recommended to me... but to be honest. Good Job! sometimes I still get a small sprinkle of hope for the KZbin algorithm. Nice work, Nice explanation keep up the good job! Happy New Year!
@RSpills 2 жыл бұрын
Just wondering why you used a dig quad and a dig uno? I was under the impression that the dig quad could run data and enough power for this size of install.
@Chase_Anderson 2 жыл бұрын
A digquad could definitely handle it, in theory you can do 600 pixels per channel and there’s also a loophole to get 5 channels out of the Digquad instead of 4 so that’s no issue. I did it this way for 2 reasons: 1) lots of people report issues of longer data runs (over 25’) and running my top roofline off the Digquad would required that data line over 30’. Using the diguno up there my longest data line is only a few feet 2) the way I did it also leaves me open for future expansion - the second data out on the diguno up tops leaves the option for me to run another line to the upstairs window and then I have 3 left on the Digquad I could do my front window, door and garage door. The caveat is that I have to make sure they’re synced right now… it would be way easier to control and schedule if it was one controller but then more work to modify later if I want to expand which I likely will.
@RSpills 2 жыл бұрын
@@Chase_Anderson thanks for the explanation. I have my lower level running right now in a dig quad…and now that I know that the ws2815’s work in the extreme Canadian cold, currently running in -30C. I’m going to start the 2nd floor of my house in the summer and try to run it all off of the dig quad. I’m going to pick up a QUINLED Data booster to help with the longer data run. Hopefully it goes well. Thanks for the vid and the response.
@DavidJJJ 2 жыл бұрын
@@RSpills We have the opposite issue, 40c + days at Christmas isn't that nice for lights :)
@ojasray1 2 жыл бұрын
Would love to get the link to the seller who made the custom lengths - I too also do not know how to cut and put together….
@MrSadlerd3 2 жыл бұрын
Happen to have a link to the seller that did your custom lengths? I'd love to purchase from them as well.
@gradmihaialexandru3445 2 жыл бұрын
Vendor for the led strip?
@dusty717 2 жыл бұрын
Great video! I did the same thing using Dig-Quads and bullet pixels. Are you using xlights and WLED?
@Chase_Anderson 2 жыл бұрын
I’m using WLED right now, I guess I completely skimmed over that part. I do have xlights downloaded and I’ve played with it a little, will likely dive in more in the future!
@sama1732 2 жыл бұрын
Thank you for sharing. The wife wants a similar setup (only the horizontal runs) and this gives us a great idea what they will look like. My project for the next holidays season. Merry Christmas and Happy Holidays.
@theLEFTY15 2 жыл бұрын
I'm curious how you did corners with the channel and the diffuser sleeve? Great video
@Chase_Anderson 2 жыл бұрын
Thanks, I bought a little hobby mitre box with saw off Amazon and just cut 45 degree miters. I got the tooth count for aluminum and I cut them with the diffuser plastic installed. I also started at the corner and worked to the ends so all I was doing was taking off like an inch with the mitre and the overall length didn’t matter, and the final cut at the other end was just a straight cut - those I cut the channel to length with the hobby saw and just used heavy scissors for the plastic.
@brucehanson4147 2 жыл бұрын
An average power miter saw with carbide tooth blade for wood trim work cuts aluminum very well and smooth. Just go a little slower than you normally would to be safe.
@RSpills 2 жыл бұрын
Pretty thin aluminum, I’d imagine a hacksaw would be just as easy.
@hockeyplayaz18 2 жыл бұрын
Thanks for the followup Chase! This is fantastic.
@manukalias 2 жыл бұрын
Very neat and clean setup 👍👍
@karthikvenkat4854 2 жыл бұрын
Thanks for the detailed follow up post explaining the install! Great job.
@bryan34wable 3 жыл бұрын
Looks nice man. I currently have ws2812’s but thinking of changing after Christmas, not happy with the 5v. With the 12v 2815’s how often are you having to do power injection and since it’s a 4wire do you leave out one of the data’s or put both of them in the data output of the Diguno? Also are yours the IP65 in aluminum Chanel? Thanks.
@Chase_Anderson 3 жыл бұрын
There are 3 separate runs and NO power injection! Longest run is 480 pixels. I think power injection started with 5V and people with 12V just think more is better but to me it would be a waste of time and money - you can decide if it looks underpowered lol. The back up data connects to ground. Yes aluminum channels and I went IP66 because I live in Canada with lots of snow and rumor is the ip65 are not waterproof on the back. So IP66 is in a silicon tube completely waterproof, but doesn’t have the epoxy coating the IP67’s have so easier to fix if there’s an issue.
@bryan34wable 3 жыл бұрын
@@Chase_Anderson awesome. I’m in central California so not so much rain let alone snow. My IP65 are holding up. I’ll probably have to do power injection just not as much as I do now with the 5v. My lower roof line has 4 strands in a row and with 5v I injected power at every joint.
@Jasonoid 3 жыл бұрын
How did you end up mounting these to your home? Hard to tell from the video. Looks great!
@Chase_Anderson 3 жыл бұрын
Just with the provided clips and screwed to the bottom of the soffit. I said I would make a video showing it because I can’t post pics in these comments to show it, I’ll make it my goal to have it up within 2 weeks of this comment.
@Jasonoid 3 жыл бұрын
@@Chase_Anderson all good, thanks for the reply. I understand the work that goes into these videos having a channel of my own lol
@hockeyplayaz18 3 жыл бұрын
@@Chase_Anderson Awesome work! Can you throw a parts list and links in the description when you make that video?
@Chase_Anderson 3 жыл бұрын
@@hockeyplayaz18 will do. I plan to film it tomorrow morning as long as it doesn’t snow!
@Chase_Anderson 2 жыл бұрын
Here you go, kzbin.info/www/bejne/m2OmgZ6aipmenaM
@rykerholms2613 3 жыл бұрын
Do you have the channels facing forward towards the camera or are the pointed down?
@Chase_Anderson 3 жыл бұрын
They’re 45 degree (called v shape but more like L shape lol) channels so kind of down and out, I think good for my setup because it slopes down towards street.
@bigmahlman 3 жыл бұрын
Looks amazing, been thinking about dong a simular project but a little lost on some of the specficisc. How many LEDs per meter did you use? How big of a power supply was necessary? How often do you have to inject power?
@Chase_Anderson 3 жыл бұрын
30 led per meter which also helps on power requirements, I don’t think you need any more especially since most people view so far away. I’m using a Meanwell HLG-320H-12A which is 22A. I’m actually not injecting power! There are 3 separate strips here, each powered from from the beginning only and the longest run is 480 LEDs. My OPINION is that power injection is very necessary for 5V, but somehow carried over to 12V with many guys acting like even though it’s not necessary it’s better to power inject… waste of time and money imo!
@MrSACKBOYPARADOX 3 жыл бұрын
Looking good. I’m new to this I have the lights dig quad, I don’t know how to mount them on the facia. Can u upload a video showing us how to do it? Thanks
@Chase_Anderson 3 жыл бұрын
Sure, I’ll put something together.
@karthikvenkat4854 3 жыл бұрын
@@Chase_Anderson I’m interested as well! This is super cool. Are the strips visible during the day?
@Chase_Anderson 3 жыл бұрын
@@karthikvenkat4854 during the day the lights definitely aren’t as impressive. I’m aiming to have that other video up in 2 weeks, I’ll include a clip of the lights during the day.
@Chase_Anderson 2 жыл бұрын
Here you go kzbin.info/www/bejne/m2OmgZ6aipmenaM
@richtodaro9919 3 жыл бұрын
Great!~!