On passenger side I removed a few grommets ,peeled back the fender well plastic and reached in.I cut a tube noodle to hold the well plastic made it easier to get arm up to replace bulb.

a turbo blanket does nothing for vehicles like this. theyre just for show on a 300 hp car

Good luck getting 850 hours out of those Sylvania bulbs , I tried them before and they were complete crap on bulb life , I kept swapping them ( under warranty) out because on my truck it takes 2 minutes to swap both bulbs including doing a alignment if needed and I got 6 Months on some of the bulbs , no I never touched the bulb all with very little Night driving !

Wow, very cleverly done dude!!

4:15 There is a much easier / safer way to do that. Just undo the two 14mm bolts holding the sway bar bracket to the chassis, on each side. This is easier than unbolting the sway bar from the end links, and allows the assembly to drop low enough to pull the spring out without any extra hassle.

Where did you buy the sensor

Does the headliner have to be out to remove all the sunroof parts? Or can this be removed with the headliner still intact?

Actual life saver

I'm shocked, $20..... $40 now under bidenomics.

I was back again to remind myself of the procedure for the drivers side. A flash light is helpful. A nuance that I realized is that it is easier to remove the connector while the old bulb is still held firmly in the socket then remove the old bulb. When you remove the old bulb just before you take it out make a mental note of the angle at which it is free of the socket. Then when you put the new bulb in you can duplicate that angle. Put the new bulb in first and the put the connector on. When reinstalling the radiator over flow tank use the flash light to help line iup the plastic area held by the clip with the clip. Tilt the top of the over flow tank towards you and push down. Usually takes a few tries but eventually will go in.

6 years later those same $20 bulbs are now $40

Love the birds chirping. Sends me back to childhood.

How did you put the bride material on doors

Didn't work on my 09

Passwnger side is easier than driver side what are yall talking about 😂

Good job

Dude you are a savior, if anytime you are in Culiacan Mexico you ve got some aguachile for sure

What are the exact name of each bulk head fittings used?

Helpful except it was EXTREMELY DIFFICULT for me to get the coolant slotted back in and I'm still not totally confident it's back in right.

litering is so cool. what a douche

I would add some more reflective heat tape to the intake. I would also show the right side change too.

It's still a Ecotec motor... made popular with a turbo by Saab in the 9-3 for the last 20 years. These new ones simply have direct injection and run more boost.

The fuel level sensor still holding up after running e85?

Thank you! This was super helpful and easy to follow!

Omg brother you are a life saver I was told I would had to pay hundreds so they can open my trunk but the your method work like a charm thank you so much 🙏

Thank you for the How To

you are a legend - worked a treat

What rear lip is that?

Thanks guys.

What aboutca 2015

I loved how he stopped at Walmart and grabbed q hot wheels car 🥺

Can you send me the link for the sunroof board I don’t know if the sides are supposed to have over hang of material or the sides

Billy!!! You saved me, Brah!! Worked a Treat!! I can now fix my trunk cable!! Thanks, Man!!!!

U definitely need to cut more rust out because its just gonna crack and rust more

Hell yea thank you man quick and easy video

6 years later and still helpful.

compressing fiberglass insulation reduces r value

Update??

Dude only the vtc actuator gear moved when I was trying to take out the spring and it went forward a bit while every other gear stayed in place I tried to start it up n it sounded horrible that was for like 2 seconds Im really stressed out, its at the shop but without looking at it theyre saying it may need a new engine or something crazy like that

This technique worked for my 2011 Acura TSX. In my case, the release cable was surrounded in a grey foam. I used a screwdriver to lift this cable up so I could grab it with some needle nose pliers. I was able to pull this cable with the pliers and the seat released

Just open the boot bro! 🤯🙄

Clean FA5 man I have one just like it but in black. Do you have any videos of how the finished headliner looks? I need to change my headliner as well and your video is the only good one about 8th gen headliners lol. S/O from NYC.

Entonces se preciona la pieza verde,y así abre????

Yo no puedo abrir

Si es comun.

Wheel arches suck the worst

I dont need a high ass expensive truck or expensive carr Just want something to move around you know

Dude I need a carr just to go to work and home and Walmart I'll give you 1,000 box but I live in Moore county

U still got the 8th gen Si ? Thinking of picking one up for $9k from a dealership

I love that every honda owner has to pop their front bumper back in by the lights! 😂 I don't feel so bad now