Needed to see this !!thanks for the share. I am new to tech and this will go a long way

Wow . Thanks for the share. Recently transitioned into IT and this video will go a long way

Good job

,Hindi ma

Been doing cable infrastructure for 20 years. Almost every place I have worked we were absolutely forbidden to use tie wraps on the cable.... Velcro only, or in the case of central offices or AT&T buildings, 12-cord. And the next cable monkey I catch using snips to trim the ends off a tie wrap gets a smack in the back of the head. At Lucent, we were required to use flush cuts. I got in the habit of using flush cuts real fast where we were allowed to use tie wraps. A tie wrap with a jagged tail sticking out will flay your arm or hand open so fast it ain't funny! Looks like yours seem to be trimmed nicely flush. Good show.

Very Nice

I know this was a tutorial, definitely beautiful structuring, but shouldn't you have maintained the twist as close as possible prior to termination? We are always demanded by construction specs to keep twist right at termination at the patch.

bad cables harnessing

Without labeling, your guys are going to do alot of walking from room to room to tone those cables out. Unless it's a tie panel to other floor patch panel.

Thanks for the good work

Good thanks

Cable look terrible , used valco not tie rob

watched in 2021 nice work

Keep the twists going as close to the termination point as possible.

Man I wish I got load bars to work with. I’m trying a non-load bar solution with straight on termination for a bit to see if I can get it to meet my standards. Who knows, there’s a thousands ways to skin a cat.

zip ties on cat cable SMH

Excelente trabajo colega

Thanks for a great video. Best part was needing to put on your...ahhhhhh...young man glasses. Same boat here brotha 😉

Super boulot

Complete amateur.... That knife ?

Very imformative thanks for the video im trying to learning 😊

Worried about you razor blade saftey skills Great video

This looks horrible. You wouldn't last an 8 hr shift at my company. My supervisor would whip you with those tie-wraps as you were being escorted off the jobsite. KZbin needs to do a better job reviewing videos before putting them up on their website...

Cable p0rn

Ele escolhe o cabo à toa não o têm numeração nos cabos, e isso mostra k nao sabe o k faz. Em redes estruturadas é super importante marcar os cabos para k na outra extremidade saia certo. Imagina do outeo lado desses cabos tens pontos duplos? Como ele vai fzr? Vai meter os cabos à toa? Têm k meter is numeros seguidos. Tipo pontos de rede : 01 A 02 ai a etiketa têm k bater certo no nr do painel. Esse cara ai não sabe o k faz...

U need to folow the numbers in cable to have a pair strait in the oder end man. I guess u have cable 1 and 23 for exemple in the oder place.. always numbers and respect the order of the numbers

This is the kinda boring work as a System admin I hate doing. I would always contract this out.

kzbin.info/door/tQhbKQhLYKEyy4tKcgvi_g

Que trabajo tan feo

Buen video informativo

Great dressing job, but NEVER follow his instructions to strip the wire. Commercial strippers are cheap and do not cut the insulation on the inner wires.

you almost sliced your neck to death.

Nice Terry, tkiu.

have you tried these yet? mnpctech.com/buy-stealth-cable-combs-for-pcs/cat6-6a-combs/

Very nice job!

In my opinion, the amount of cables grouped does not seem appropriate. You should separate into groups of between 15 and 20, take them apart to improve the insertion (IL) of them and in addition to avoid electromagnetic induction, this is important if the network should then be Certified. About CAT6A no more than 10 cables this is due to the frequency that handles the cable. On the other hand I agree on the use of the corresponding tools and materials (cable ties and shear not indicated for such operation) this will make our installation is standardized, avoiding damage to the network materials and during the process to avoid accidents by not use the corresponding tools.

Dear Terry, you did good job, every person have his own technique. bottom line fluke should pass it

we are not allowed to use tie wraps ..only velcro in OZ

Gosto muito deste curco, gostaria aprender.

wire tire not best to use ! can pinch wire and can not ad any new cables Velcro best to use

Ive always been told NEVER use cable ties! Always use velcro Strips to support cables

Mark cables always and than put them in to the patch panel, my rule

That's crazy using a box cutter always use your Snips and your pull string

This video is Garbage.

работать навесу, без стрипера - прекрасное руководство как делать не надо.

untwisting the pairs. you have no idea how to terminate. like to see this fluke tested

Thanks for guide us Mohamed asad

Very nice. Thanks.

This looks so ugly

very nice good job