Solid content, I just replaced the two on my 12 Xterra 4.0L, mine was leaking oil from the o ring on the driver's side. The passenger side was under the intake manifold and I got access to it by taking off the throttle body. On my SUV, they are different part numbers according to the side they are installed. Thanks for the video, it will help a lot of DIY people and me as well.

The video how remove another selenoide ...???? The firth is easy

The secon

The secon

I have nissan murano 2007 problem cod..P0081

I have the same code and replaced both with new parts. But still have the code. Why?

Do you test it with the 12volt battery?

Great video thanks for explaining everything. It helped a lot

Bread chickens, leave the wheels alone

Suicide, you are a ZERO!!!!

Do I have to line any belts back up?

Thank you. Your instructions worked perfectly. I needed a circlip pliers for the back electrical fitting. Luckily I had one from working with VWs.

I like how you actually troubleshoot instead of just blindly changing parts, hoping for the best

Колодки поставил неправильно,и еще ошибку сделал что смазал направляющие они не предназначены для смазки

Thanks ive been looking for somethings like this to a while.

For the 06 charger is it better to use non adjustable or adjust lower ball joints?

I have 2009 cobalt and I threw this P0300 code today. Same thing with starting, it starts but you can tell it doesn’t want to and it actually didn’t start for me today. No check engine light though & mine doesn’t vibrate. But I’m going to check the exhaust tomorrow and see. But so far all I notice is when it’s starting.

Hey bud,,,,YOUR FIRED.

Awesome video man! GOD bless!

2006 Nissan Maxima , controls on steering wheel don't work at all

thank you

This really just worked for me 🎉thanks so much

Thank you sir. Good video.

My car won’t start. Connected everything. Any idea why? I reinstalled everything as it was. The car attempts to crank but don’t start. Also I noticed that the fuel pump doesn’t make the sound when the key is turned.

Your video is very well explained, but I can't loosen the nut that goes just above the oil filter, it measures 12 mm? How can I loosen it without damaging it?

Sensor?

So I bought 07 Silverado n drive n 3rd gear r gone ,is that shift solenoid

Great training..Thank you sir.

Glad I only have P00011; that back solenoid looks like it might be hard to get off without removing the manifold

It's your vapor canister not the leak pump

How you get the other one out??

Tengo una camioneta igual seis cilindros, ya se le cambió el compresor y más cosas del aire acondicionado. El año pasado dejé de usar y ahora que la prendí no sirve otra vez el aire acondicionado que crees que pueda hacer ??

If you are free to do what you want the. Everybody is free to comment what they want on you videos Theres always haters around

I replaced one of those in my dodge.That job is a mother fucker. It was a pita. It fixed my gas cap light. If your doing this for inspection, The car only does the evap test between 1\4 and 3\4 tank of gas. I ran the car nearly out of gas disconnected my battery to reset the ecm and ran it threw inspection and it passed.

where did you get the cams? are those original or reground camshafts?

Grease was incorrectly applied The bearing surface was completely missed out. (50+ years tech)

If i dont get a correct plate i can drill the holes por the plate?

Perfect

I know I'm gonna sound really stupid but I have a 2009 nitro that used to belong to my dad so I'm not familiar with it. Did you say you needed to push the middle button for the AC ?

Never ever buy an explorer with a 4.0 i was warned i didn't listen and i lost 1500 bucks

Thanks for time to show. No need to go under and remove oil filter as you found out later. Center Nut you are referring to CAN BE removed from top. You may need to remove parts for clearances but it is much easier than going under car..

Thanks so much for that video. I just spent my Saturday fixing my P0401 code and couldn’t have done it without your guide. I’m giving my son the 2005 Honda and I’m trying to get it ready for him. Thanks again my friend. If you’re even in Buffalo NY the wings are on me.

How sad you had the right tool for the ball joint . You live and you learn tho right . lol I could do that in my sleep 😴

Do you happen to remember where you got the gasket from? A link would be very helpful. Great video by the way!

Damn bro, no fucks given lol no masking off your wheels, not enough clear coat they have kind of a matte finish to me. Also, your wheel are scratched to shit! Let me guess, those wheels never come off they stay on all year round? If your trying to make your whip stand out and make heads turn do it right. It's rushed my bro, OH! another thing painting in direct sunlight not a good idea my Boi. You want to be in a cool shaded spot and where there's no dust. So being outside your most definitely gonna have dust particles even if there's no wind or breeze. Have to be in a dust free environment to not risk debrie or dust on your finish. Can't rush these things bro, that's why so many ppl are giving you shit in the comments. What's the point on spending money on expensive aftermarket shit for your whip if your gonna try and make your whip be a head turner do it right, take your time and most importantly take pride into your whip. I'm not trying to make you look bad brotha, im not hatin just somethings you know you should do more that you already know my Boi.

Actually. You should not be touching that stuff with your bare hands .

Ok I changed my water pump and then started car and my check engine light started flashing and car runs really rough now. Is the timing off? I changed spark plugs all of them but I need to know how to remove the timing chain and the pulleys please n thank you. Your video here helped alot.

Thanks for the informative vedio. Is it true that a bad ignition coil will affect either cylinder 1 and 4 spark plugs or cylinder 2 and 3 spark plugs. As to your example spark plug 1 and 4 were not sparking.

Too much unimportant talking and chatter. Just go boom here it is guys...

Thanks my brother.