you should also have shown how you did the bottom part. you just talked about it.

Thanks for sharing pro tips my friend. I heard u say at beginning about dropping half inch but leveled everything else. Question about slope, I’ve got 2 corners that have sunk low over time and me putting ladders up against. Flow is terrible and water holds in corner where gutter wraps around eave corner, how does one tackle corners? Down spouts are at both ends fairly long run like the one in this video

ay! dont point that at me! never point a gun at someone like that!

We are a representative democracy we vote for our representatives and then they vote for us at least that is how it’s suppose to be. Call it what you want but our representatives can’t vote on anything unless we first vote for them case closed.

You dont have to crimp anything... all you have to do is crimp it seven times

Tommy is a God amongst men in the carpentry world.

Yes, I will definitely want one of those.. Getting those 4 inch elbows together nicely has been very challenging!

Dude thats sick af!

You’re getting that decorative and that particular about a freaking downspout now? What is this world coming to the most important things in life aren’t things and don’t point that gun at me again young man we’re gonna have an issue.

Need a slopping compound miter video 🎉

If you come to a house where the drip edge is screwed on tight, do you unscrew it or do you extend the drip edge and add charge extra?

Loss the sun glassed

For your standard expansion we always notch one gutter and slide them into each other so it still looks like one continuous gutter from the ground same concept tho put two end caps in there and cap the top. we also make our end caps to fit inside the gutter without the extra lip

Where did you purchase hangers? Thanks!

How do you reinforce the gutter to handle the weight of the chain?

Man, I just started installing gutters a couple of weeks ago, and these marks are the bane of my existence! I have to clean the gutters with microfiber and wd-40.

What is Bonderite?

Stick to Gutters, and try staying out of the gutter next time

That front wheel caught my finger one time and tried to pull my skin off😅 I think I'm gonna find one of those sponges on a stick to do this from now on

How far was your spacing between hangers?

Hey Josh, I have a question about expansion and contraction on a 6” k-style gutter that’s 80ft long. When doing the end cap expansion joint how much of a gap do you leave between the two.

That’s cool and all but I can’t see anything your doing ….

Would you guys recommend investing in a generator for a brand new gutter business? Do you ever use them? I'm in Austin so it's not exactly comparable to your market, but just wanted your thoughts.

I had a gutter fall and im so glad i found your video with your complete detail on everything you did. Thanks MrGutter!!

Absolutely correct re. rubber expansion joints. I made the mistake of using them with mitered corners around my hip roof. Expensive, a pain to install, and a 2-year lifetime before the rubber rips. Do NOT miter corners on long runs, cap the ends and let them float.

How far should the gutter be below the drip edge

I have this issue. Can’t I just run a bead of outdoor caulking between the drip edge and gutter?

Can you please show how you do a Gable Dormer. Do you cut to match slope of roof or just stop it short and throw and End cap on?Thanks in Advance

Great video.

This example of rain in his demonstration is ridiculous and not at all realistic to what occurs outside

Rotate on the shaft.

Gaf. Take a guess.

I'm not a gutter installer, but I've done lots of fine granite work, and now I'd like to transition into gutter installation. You don't have to tack the middle of the gutter two times if you have made a mark on the facia where your ladder is and marked the gutter at the same distance, then you can match those two lines and don't have to go down to check if the gutter is aligned on both ends and unscrewing to aligning the ends... Otherwise, I'm getting great value from your videos. Thank you very much!

In the video you say you're using rt angle tin snips? In the links it goes to left angle? Which is correct?

I wish the Rt Angle tin snips didn't cost so much.

Thank you for your video. Does anyone get cut walking by the sharp cuts? I think I will file mine down a bit?

Thanks soooooo much for the z flashing tip..

Thank you so much .... these are exactly what I am looking for to move the new gutter downspout extensions out of the way on lawn mowing days! And the installation looks so easy peasy too!!

Looks sharp

Reading a lot of the comments here, people seem to think that a DIY video should *not* be professional. I guess, as a DIYer, I want my work to end up as professional-quality as possible, maybe even better (noting that a lot of pro's are sloppy or cut corners).

This old house folks know a thing or two about construction work, but don't trust everything they say, one day that old man was demonstrating how to install shingles on a roof and the first thing i noticed was he installed the starter shingle upside down 😂 i had to take a screen shot of that.

I love that box downspout. I was blown away by the Box downspout with the open channel. Do you save any money bending your own downspout verses buying it?

excellent work

Outstanding

This video was really helpful! We installed gutters this morning using TOH’s video (which was a great visual tool). But unfortunately when it rained this afternoon, rain poured behind our gutters because we didn’t install under the drip edge like you recommend. I wish we had seen this video before we started to have a different option!

What is your method for cutting the downspouts to length, appears you use snips. Can you give a detailed explanation and why you don't use sawzall/wheel grinder?

I have to do this on a mobile home. Thank you for the tutorial.

I'm moving away from truck and trailer for my gutter company into an E Transit. How do the tires hold up having all the weight of the machine and coils on 1 side? Also do you load your scrap into the van? Thank you

Do you have one for 6inch?

What's eavesthrogh you mean eavesdrop , where water falls into gutter....explain I might be miss reading