My 250r starts first kick when ice cold never need the choke. Rich?
@duneblogger68124 күн бұрын
Could be. If you arnt having other issues i would just leave it alone
@Fox250R24 күн бұрын
@@duneblogger681I’ve gone from a 185 main to a 170 and 60 pilot to a 50, top end is sputtering can’t figure out why.
@duneblogger68124 күн бұрын
Ive only worked on banshees so not sure what size mains you need for a 250r, but ive use 48 pilot jet in keihin carbs. Having to big of a pilot just could just make it rich and sputter at 1/4 throttle if you dont have enough air to add to it with the air screws. Wouldnt worry to much about that. But if it sputters up top, that means its rich. Just check you plugs and see if its black or brown. You want it to be golden brown
@Fox250R24 күн бұрын
@@duneblogger681jetting this thing has been a pain in my ass for many years! I’m going to go on a limb here and say it’s the 38pwk.
@Fox250R24 күн бұрын
@@duneblogger681I’ve also had air Strykers still can’t tune worth a shit :(
@motormouth24722 ай бұрын
Those early 5.0 Modulars are probably one of the best V8's I've ever heard. This video brought back some memories of my dad's old 2012 F150 with the 5.0, I miss that truck.
@duneblogger6812 ай бұрын
I did sell this truck. I miss the sound and how fast it was. Upgraded to a f350 6.7 for towing now.
@motormouth24722 ай бұрын
@@duneblogger681 ahh nice, those 6.7's sound great too. My next vehicle will probably be a 5.0 F150 whenever I can afford a nice one
@Floridawoodsbanshee7 ай бұрын
Are you still riding banchees?
@duneblogger6817 ай бұрын
Yes i am, just havent uploaded a long time
@tomj337 Жыл бұрын
Mine does the same when I chop the throttle the revs hold high for a while before returning to idle is this the same?
@duneblogger681 Жыл бұрын
In this video it was pretty boggy. If yours has a hanging idle. Kinda like what you said, revs up then takes a while to come back to normal idle, it could be your air fuel screw needs to be adjusted (turned in a half turn) see if that helps. Or you could have a slight vacuum leak around your intake gaskets. Hope this helps. Id try the air screws first. A good ball park is 1.5 turns out from being fully seated to 2 turns out.
@mudboysoffroadtoys66872 жыл бұрын
I don't wanna see his back pockets 😭bro😶
@azmacoroni11892 жыл бұрын
What size are those 4 bolts in the front of the motor that hold the motor in place
@anthonyk6265 Жыл бұрын
12mill or 14
@Floridawoodsbanshee2 жыл бұрын
What A-arms did you go with? I can't tell. Alba? Fireball? Jd? I have older set of Fireball from 12 years ago. But Fireball has redesigned long travel arms. Just talked with them today. Want to update my front. Already have stage 4 elka. But they setup for MX. Sending them out for service and new trail settings. Did you like the arms on this bike?
@Floridawoodsbanshee2 жыл бұрын
That's how I would expect to do first break in ride. After 1st good heat cycle! Sounds good
@Floridawoodsbanshee2 жыл бұрын
Damm your building some nice bikes. What color blue it this?
@duneblogger6812 жыл бұрын
Electric blue
@jgrossaint3 жыл бұрын
Who's daughter is riding the yellow bike?
@derekprince61963 жыл бұрын
would be better if he didnt install in the dark.
@dabtech74563 жыл бұрын
Daaaaaamn thats a fat ass cat lol
@danielracicot87833 жыл бұрын
Glad to see someone else using the type f , first vid I have seen thanks for posting
@MFarid33 жыл бұрын
What were the silver shocks with reservoirs that you had on first?
@duneblogger6813 жыл бұрын
Yamaha 450r shocks. They worked good but werent correct length so it sat kinda low and i just upgraded to elkas and never look back they are worth the money
@MFarid33 жыл бұрын
@@duneblogger681 those are the ones that are 18.25”?? How did you get them to line up? I have +2+1 a arms but I think they’re standard travel and just dry fitting them it doesn’t look like there’s any way I’ll be able to get them on.
@duneblogger6813 жыл бұрын
Yes it is 18.25 maybe they were to long for my long travel arms i cant remember now. If i were you just buy the legacy edition shocks they are $1000 and they set them up for your weight and arms and you get front and rear and they ride super nice once you get them all dialed in. Just spend the money 🤘
@mushmanist3 жыл бұрын
Wats the solution?
@gompie2503 жыл бұрын
bigger pilot ;)
@ShotByDEBO4 жыл бұрын
Nice jeans. Wish I could see everything else. 🥴
@elloquitocriscristia4 жыл бұрын
You're loss my friend, is not a ford , why not a yamalub or amsoil?
@duneblogger6814 жыл бұрын
Ive tried a few brands out there type f seems to shift way better and smoother. Also when the bike sits for a month or so the clutches dont stick together with type f. Its 3.50 a qrts lots of pros to using it only con i have is you change it more often which isnt necessary a bad thing. Use what you think is the best man. My uncle has been using it on that bike since 1995 and i bought from him in 2014 and i still use it and transmission is original so it works great
@kekex16664 ай бұрын
How much oil
@Ghost-gw2ue4 жыл бұрын
Thanks for the very good advice.
@Ghost-gw2ue4 жыл бұрын
Was it worth the time and money besides buying one already built ? Thinking of getting a frame titled .
@duneblogger6814 жыл бұрын
Up to the person. Either way your spending money. Look at spending minimum of 3k building one. guess if you arnt mechanical inclined then buy one already done. Or depends on if you like riding them or building then riding them. Ive done both and im at the point i just wanna ride them.
@bansheemittenriders70604 жыл бұрын
Sound just like mine fuck my life
@OGKILLa93654 жыл бұрын
i dont recommend the crappy aluminum case savers. i had a alba case saver on one of my banshees, the chain broke, cracked the case saver and took a chunk off the case. i recommend a DRW performance one or TM DESIGNWORKS. those won't crack for sure
@mattgehrke4 жыл бұрын
How well does this case saver work? I was told these aluminum case savers do nothing, if the chain were to snap
@duneblogger6814 жыл бұрын
Well in the video i broke a chain right before and had the case saver on. It works, It keeps the chain from wrapping up and cracking the case . The case was damaged before. Broke a bolt i pretty much explained everything in the video. Its 25$ better than nothing. I would recommend buying a good quality chain 100$ or more and change it out every 3 years or so depending on how much you ride
@mattgehrke4 жыл бұрын
@@duneblogger681 I've gotten a lot of mixed reviews about this case saver. I heard DRW, is the best for case savers but I don't really have 80 bucks to fork over for a case saver 😕
@moemoney19645 жыл бұрын
Damn that cat big
@duneblogger6815 жыл бұрын
Haha yeah it was winter time the cat hadn't been doing much
@moemoney19645 жыл бұрын
@@duneblogger681 I tried the trans in my shee and I like it shifts good but can't seem to get carbs right and crisp
@duneblogger6815 жыл бұрын
Check out my friends channel south texas banshee he has a great video on syncing carbs and lots of other good content for jetting i should take the time and make a few videos but im just way to busy with work dont have much time to do anything at the moment
@codykuiper96135 жыл бұрын
What mods are done to the banshee
@duneblogger6815 жыл бұрын
I got 3 of them but this blue one is completely stock all original. just has vforce 4 reeds, fmf pipes, k and n filters and rejetted for those mods nothing fancy
@nathanshouse51155 жыл бұрын
The side of your case says 500 ml and you put a whole quart in ???? 946ml??
@duneblogger6815 жыл бұрын
1500 ml on the side get your glasses on. These take 1.5 qrts
@nathanshouse51155 жыл бұрын
Duneblogger have you watched your video? It may say 1500 regardless of that fact with the glare in your video you cannot see the 1 whatsoever. I don’t need glasses, and I thought it was obvious it was a question for you with all the question marks I left, haha I knew you sounded like a punk
@00MRROCK005 жыл бұрын
Whats the mod of stock one if u remember
@duneblogger6815 жыл бұрын
Well funny story i bought this banshee from my uncle and was told it was a 4 mill he had it built in 1995 and i believed it was a 4 mill because its pretty quick but turns out it its just ported good. After 20 years it finally broke down on me crank bearings were bad. Whiling tearing it apart found 513 pistions in it which are for stock stroke lol. So rebuilt it last year got a few videos on it check them out if you would like.
@00MRROCK005 жыл бұрын
Maybe he used 4 mil crank with short rod , in that case no need for 795 pistons .otherwise I don’t think a stock crank will run near to the 4 mil as i see in this vid , or maybe the good porting will gain that much of power ?
@duneblogger6815 жыл бұрын
Yes you can do a 4 mill short rod but it was stock crank welded. All matters on pipes, tires, setup and weight, and jetting. I beat lots of people cause i weigh a lot less than them lol. I run 12 paddle 22s. Had a plus 4 in this video Couldn't launch for shit haha
@nathansumerlin83913 жыл бұрын
Setup is usually worth more than power
@pedromaciasrubio92635 жыл бұрын
Wat size motor u have ????
@duneblogger6815 жыл бұрын
Just stock motor for this bike i had. I got multiple bikes. This one had fmf pipes v force 4 reeds and k and n pods at sea level
@AngelRamirez-pu8po4 жыл бұрын
Duneblogger I’m running 300 on my banshee I had got the motor rebuilt ported heads v force reeds 4s one size up on my domes and that’s it. My power band won’t kick in tho I’m go down to 290 what do you think?
@USMC-Sniper-01375 жыл бұрын
How about stickers older than a year old??
@duneblogger6815 жыл бұрын
Yeah man no matter how old this works on
@craigraptorguy595 жыл бұрын
Wish I would have known you were there I would have come out and rode with you. Great video, have fun and Merry Christmas
@duneblogger6815 жыл бұрын
Thanks buddy. This footage is from a month ago just happened to edit it today. Merry Christmas
@joebrownfield79465 жыл бұрын
Took you long enough
@trevorstednitz14365 жыл бұрын
What color is the power coat on the frame?
@duneblogger6815 жыл бұрын
Heavy silver i believe
@goldenwheeledbanshee91605 жыл бұрын
Thanks 4 sharing.
@amvanquish55555 жыл бұрын
Did you see they came out with a new design? There just like ktm plastics.
@duneblogger6815 жыл бұрын
No i Didn't these things are pretty cool for what they are
@amvanquish55555 жыл бұрын
Duneblogger still running ok? How long have you had it?
@duneblogger6815 жыл бұрын
I bought it used didn't run good at all when i got it. So i screwed around with the carb. Still backfired so i ordered a new bigger 26mm carb and installed runs really good now. I should of done a video of installing it but thought of it after the fact. Only had a few months now.
@amvanquish55555 жыл бұрын
Duneblogger what was the stock mm?
@duneblogger6815 жыл бұрын
I don't remember like 18mm or something.
@kevingalindo15 жыл бұрын
Rip it!!!
@BrandonRossVlogs5 жыл бұрын
Get new bars grips and get rid of the plastics
@duneblogger6815 жыл бұрын
My bike my rules
@BrandonRossVlogs5 жыл бұрын
Duneblogger 95 purple plastics with renthal bars and black grips no bar pad would look clean asf. The plastics and bars make it look shitty lol
@duneblogger6815 жыл бұрын
@@BrandonRossVlogs it had the purple and yellow plastics that looked shitty so i painted over them. I do have a new set for the rear but fronts are staying
@duneblogger6815 жыл бұрын
@@BrandonRossVlogs the handle bara stay to i like the way they are. Also rode on the bike when i was younger with my uncle and held onto those bars so sentimental to me. But yeah eventually find some renthal bars lol
@kevingalindo16 жыл бұрын
First like first view!
@dyllonhaines73216 жыл бұрын
Love watching build videos!
@duneblogger6816 жыл бұрын
Thanks man i loving doing them
@82raptor6 жыл бұрын
I just bought the flowmaster American thunder system with the super 40 muffler and that was too loud for me. I am going to custom fab a super 50 and keep the stock resonator on my American thunder system. Annoying loud exhaust pipes are like herpes... great fun to catch, not so much fun to live with every day... J. Clarkson.
@duneblogger6816 жыл бұрын
Yeah keep the resonator on and it will help these 5.0l are loud once you delete that resonator
@jackmoyer74376 жыл бұрын
Yea thats how mine was after i broke mine in after rebuild now i got her richer and runnin hella good.
@reggiexp69 Жыл бұрын
same it was all fine after rebuild 6h later but also temps droped from 35C summer to 20-25C Celius i had it running great (1.5 or 2 turn air screw) no snorkle on air box stock lit no holes and twin air air filter, 22.5 pilot 210 main. ran great till the colder temps it had a horrible bog low end like it falls on its face... so i put the snorkle back on the airbox lit, a bit better then someone said turn air screw at 1 turn and i did that and boom it works again but yeah that means pilot was lean what seems logic i see its 25 not a 22.5 and my carbs are 26/28mm rdlc 31k carbs that are a bit different. anyway i ordered 25 and 27.5 pilot jet waiting for them to come, hope that fixes my issue so i can remove the snorkle and turn air screw at 1.5 or something again cause it does run but it feels like its been hold back.
@kevingalindo16 жыл бұрын
Awesome !
@okiebassmaster12496 жыл бұрын
Anybody else not getting 18 mpg out of their 5.0?
@duneblogger6816 жыл бұрын
Mine is a single cab less weight and all freeway
@Joah1325 жыл бұрын
I get a beautiful 14mpg... I'm a crewcab with a 6.5 bed. But I have an intake and a tune.. I hoped that would've helped, but no..
@duneblogger6815 жыл бұрын
@@Joah132 I got less weight man crew cabs add a lot haha. SINGLE CAB LIFE!!!!
@Recoil8165 жыл бұрын
I get about 16.5. Maybe 2/3rd of my mileage is highway going back and forth to work.
@joebrownfield79466 жыл бұрын
Yellow bikes a stock stroke you lying son of a bitch
@ezq66646 жыл бұрын
Beautiful machine...
@bossmanpoppy60116 жыл бұрын
Hey are you still building bikes
@duneblogger6816 жыл бұрын
yes just finished one. need to edit and put video on here just been super busy with work
@bossmanpoppy60116 жыл бұрын
@@duneblogger681 Alright Cool
@bossmanpoppy60116 жыл бұрын
@@duneblogger681 when you get a chance I know you probably super busy can I get your information so I could talk to you about building me a bike
@duneblogger6816 жыл бұрын
@@bossmanpoppy6011 not sure what you need help with i just do this for fun but i know a guy south Texas banshee he helps people out all the time
@bossmanpoppy60116 жыл бұрын
@@duneblogger681 oh okay cool I was just trying to see would you build me one in I would pay you for the parts plus your labor.
@thelocalprospector63086 жыл бұрын
Nice job on the banshee man just one question HOW DID YOU GET THE TOP BOLT OUT FRONT SHOCKS...???? IM STUCK
@jacystone50116 жыл бұрын
Nice
@jacystone50116 жыл бұрын
What is the 3 song
@rapstuff54626 жыл бұрын
Can you text me on Instagram,snap chat everything to get and maybe directions text me them I'm new to all this
@rapstuff54626 жыл бұрын
Or everything you need for the blue one
@rapstuff54626 жыл бұрын
Can you send me on Instagram everything you need for the blue banshee and how please I'm trying to learn