I too like opaque bulbs outside and jewel tone inside. I was just thinking, Is that weird? 😆 Guess it’s not just me.

has anyone found the small can other than tomato paste?

did you put anything on the mirror to help with reflection

banding is too obvious for a quality product x and y rails resolution or qc vibrations??? WHY WHY WHY

BANDING- CAN SLOWING IT DOWN HELP>

what is the deal in placing flammable wooden walls in a shop? So you understand sheetrock. Appears you have nice bright lighting (for camera or shop use?) Low subs and they still sent products- great for all Wahta about cutting thru metals? thick AND STEEL VS ALUM SHEET

I just turn 67 years old, I was very weary that the trades were going away with the old generation, I am extremely glad that this new generation of woodworkers are taking this very rewarding trades, when you build anything it becomes your legacy to the world. Keep building, keep our woodworking skills alive.

Template?

Where is the pattern?

Cross cut sleds are one of the best jigs you can have!

I love that you have your tongue out when you work. I do the same.

A bit of advice from a picture framer…don’t use wire for hanging, use 2 d-rings (one on each side towards the top). It will then hang flat against the wall and it wont ever tilt.

Rivets

Gotta love those childproof tube-tip slicers...

I have neither the tools, the skill, or the ambition to make this. Just tell me how much you'll charge to make me one LOL

Did you wet the rug prior to engraving?

Looks like the first thing you need is an outfeed table.

Can I use 1 raspberry pi 4 for the light burn bridge and camera wireless? Or would I need 2 raspberry pi?

Can’t find templates for these.?

Maybe you coverer it, but, are you using the stock air pump for air assist or do you have a air compressor connected for higher pressures? Great comparison

Interesting fact, my Thunder Nova 100 watt at 5 speed and 50% power engraves like a dream on clean stainless steel, no sprays.

Thanks for the video love this idea.

What were your settings for this?

Can you use black spray paint for reflective surfaces?

Farbermade sounds much better :D

Beautiful work !

A Wen spindle sander makes quick work of sanding these

❤❤❤

where did you get the diffuser sheets from?

This kit is crazy overpriced just go to a supplehouse like Locke supply and buy your own pieces, you can buy 50 feet of snap lock in five foot sections for $80, and 6 inch adjustable 90’s are 3.00 lol

Stumbled across this 4 years after the fact. Did you consider soldering the cutter or is the metal too flimsy to take the heat?

That must hurt. I lost count on the number of times I got hurt just this past weekend. From hitting myself with a 5/pound hammer trying to knock out a ball joint to scratching my hand on the wall because the space I was working in was so tight. I feel your pain!

Love this project. We are going to make it this year. The stir stick holder is brilliant for the paste cans. I was wondering how I was going to get those installed.

Maybe I misunderstood what your mistake was with the gap between wall & upper boxes, but that is to be expected. If the base cabinet is level and the upper box is square, then there will almost always be a gap to shim & hide at the wall as walls are rarely perfectly plumb. Typically fixed by scribing an end panel to the wall to hide the gap.

Co2 or diode laser?

Such a lovely little project, will be trying something like this for sure in a few days time when my laser gets in.

Cool technique and a beautifully crafted sign 👍

so satisfying to watch..

Rubbish

you did a good job BUT it does not look like the same quality as a Hermes not even close but from someone who does not care or from far away it looks similar ,someone who can afford these can tell the difference but to those who are not a customer of Hermes or even want too be I can see being fine with it and not understanding why anyone would pay more when this looks the same but doesn't

Very nice. I am looking for a template for a bandsaw duck in boots but no luck. I can't draw for all the tea in China. I may have to try the rabbit!

Awesome🎉

Great video. .thank you. I just bought a used system and am getting ready to install it. I sent you a request for the PDF files! thanks for doing that! it will help immensely. I subbed and rang the bell!

Super groetjes uit denhaag holland

Just found your channel and it’s great! Why’d you quit KZbin? It’s been six months since you’ve posted!!!

Tape because of the laser?

This looks great. I built an Ana White miter station several years ago. Last June I disassembled it and my husband repurposed it in his garage. I had intentions of building a new one right away. But during that week I hurt my back. Other projects got in the way and I’m just getting started on building my new miter station. It really has sucked not having a home for things. This past weekend I built a rather large drill charging station/tool holder. It really has me motivated to get my build going. Thanks for the motivation.

On the subject of DPI, the larger the dot size the lower your DPI should be. If you run the DPI higher than the dot size allows you get each line burning slightly over the last, basically destroying the detail in the picture. Print samples in increasingly higher DPI staring from 100dpi with increment of say 50 dpi. Get a USB microscope if you can and then check at which dpi the lines only just touch. Do the test for each of your lenses. Your 2" lens will probably give you more detail at a lower DPI. On a personal note, it's a pleasure looking at closeups of your hands. On so many youtubers and especially laser videos, people haven't cut their nails in months, not to mention the dirt under those nails.

put the T nuts on inside of boards so ytou are pullimg them tightewr instead of pulling them out..

I hope you are still monitoring these posts: I have followed you 'til about 8:28 minutes in when you are at ./cam2ip to see if it is activated and running, and I get an error. The error is "john@Laserpi:~/Desktop $ ./cam2ip camera: inappropriate ioctl for device. I would very much appreciate your help.