Red River Racing

Пікірлер

@logancorwin8983 3 ай бұрын

What’s the status on the car

@largesfc 8 ай бұрын

Did those 10 bolt tubes slide right into the 8.8 tubes?

@teabag402 Жыл бұрын

What became of the car?? We need an update!

@radkesrods1184 2 жыл бұрын

LMFAO. niggas out here fresh outta diapers barely hittin puberty acting like pros n shit cuz they got a camera. plebs.

@AlexPerkins252 2 жыл бұрын

Do you know what size those spacers/reducers or whatever you’d like to call them are? I’m trying to do this myself but I can’t find the size

@jimbo9357 2 жыл бұрын

I have 3 third gens. Working on my 86 TA WS6 now. Some good ideas in your vid.

@H00K-KING 2 жыл бұрын

What about putting 35 spline axles in it. Go big or go home

@asli7955 2 жыл бұрын

This guy looks familiar

@GarthJwells 3 жыл бұрын

How well did the 4l80 fit? Doing a 6.0 swap out of my truck soon

@car46999 3 жыл бұрын

You mention that the 8.8 would get sleeved at 2:14. Were sleeves needed, or did the 10 bolt axles slip right into the 8.8 tubes? I have seen some internet posts stating that they will slip fit into the Ranger and Crown Vic 8.8 axle tubes.

@motherlovinsnuffstar 2 жыл бұрын

From what I've read (on the Agearhead4life FB page) if you use a ranger 8.8 you don't need the spacers. Supposedly they taper before going into the center section.

@aaronmcdonald8423 3 жыл бұрын

Awesome set up man!.... My fuel system is almost exactly like yours i just have to finish up the wiring for the pump....my question is where did you hook up your ground for the fuel pump & where did you hook up your ground for the sending unit (fuel gauge)?

@redriverracing8985 3 жыл бұрын

I used all the factory wiring for the fuel sending unit, I believe the wires were black and purple iirc. I wired the ground to a clean spot on the chassis with a big self tapper, I think it was in one of the holes where a heat shield was at some point

@aaronmcdonald8423 3 жыл бұрын

@@redriverracing8985 was the ground that you used the big self tapper on the frame in the back? Or somewhere else?

@davidz1189 3 жыл бұрын

I like your Video on the 8.8 rear end its my next project.. How ever would like to Know how your exhaust turns out will you be installing a True Dual exhaust?

@redriverracing8985 3 жыл бұрын

Im a cheap ass and didn't want to pay $550 for the true dual kit that needed to be modified anyway. I have a 3" single pipe with magnaflow muffler that I ordered from summit for less than $200 total and I will make some piping to merge it to my headers

@dilligaf9199 3 жыл бұрын

Good video. I will be saving the previous one to favorites for the 4l80 and 8.8 info references. Keep the vid's coming...

@redriverracing8985 3 жыл бұрын

Will do, the camaro comes out of winter storage this week! Any questions feel free to ask

@characterdevelopment2361 3 жыл бұрын

Will the 7.5 tube take a 31 spline swapp

@redriverracing8985 3 жыл бұрын

yes it can, and I didn't realize that dutchmen axle made custom 31 spline axles for a small amount more than I payed for the 28 spline. Had I known that previously I probably would have gone with the 31

@characterdevelopment2361 3 жыл бұрын

@@redriverracing8985 I was thinking they did I wasn't sure . This is a street strip build right?

@tylerhaycraft7381 3 жыл бұрын

do you know what year rangers can use the 28 spline axels?

@redriverracing8985 3 жыл бұрын

I believe all rangers that had the 8.8 were 28 spline, but it has been a while since I really looked into it

@jasonscott6731 3 жыл бұрын

Was that a pace car model?

@redriverracing8985 3 жыл бұрын

Yep its an 82 that was originally an indy 500 pace car edition. Paint started to peel so previous owner sanded and primed over the blue

@eliseol.6788 3 жыл бұрын

Hey bro could u share the link for the transmission crossmember

@redriverracing8985 3 жыл бұрын

PA Racing website is under construction right now, but join the lsx swapped third gen group on facebook and look up Matt Walter, he is the dealer I ordered through

@djrowe10 4 жыл бұрын

Your sleeve concept is something diff builders like me have done with GM 8.6 10 bolt smaller axle tubes with 10 bolt 8.5, 8.2 ,or 7.5 axle tubes on top. I always weld housings cold. Heat treat is only helpful if doing cast iron that gets super hot like manifolds that have flexing and expanding issues. There is lots of theory about it out there. Like the video a bunch and am now convinced more young guys are making tons of LS engine builds and drivetrain videos preserving and modding hot rodding classics then any other time 🤙. Keep on creating your cool build with more videos coming.