What about if you do not have access to the PLC to put force on the terminal, how can continue the troubleshooting./

Me, the other maintenance dude and the plant manager carry's this knife. It's a goodun. Lightweight, good working length and holds up to daily use at the plant or in the field. Just right.

You are really gifted in teaching this clearly. Thank you so much.

Is the pls short circuit protection on on the output side?

Thank you!!

Starts by saying he's not a metal fabricator. Proceeds to use equipment only a metal fabricator has access to. Just kidding with you, i used my cousins automotive shop all the time and got to use many tools that I wouldn't normally have access to. This was positively brilliant. I am hoping to make something similar for my round table.

Whats the practical representation of the and gate "here "

Great video. Straight to the point. Thanks.

Can u also upload how did u set uped it, step by step, and all the components used in it.... 🫠🫠🫠

If possible please explain about meter in/meter out with PRV.

I diid this on my brothers house but removed the sticks and screwed metal plaster channels on the walls , and used pine battens on the floor to reattach the skirting

It's swank!

Good job I’m glad you showed me how to do the fan so it goes through the wall cause I got it GE too

Working on a bathroom with 1970 Sheetrock. It's falling apart at the bottom so I am going to have to put some shims in. Uggggg thanks for the video.

Nice thank you

Thank you sir for this video.

Thank you sir

You have just saved me 4 hours of readingz and practically saved my trade test. Thanks

Well, it didn't work for me, one the switch on the unit has 011 we got this from someplace else and I'm trying to connect to it with a switch or direct. I'm thinking that it was address as 192.168.1.11 but no luck, my laptop is 10.98.4.8. I have an CLX 5000 with two enbt cards, so I made the 2nd card address as 192.168.1.10. my network is 10.98.4.3. connected to the switch I can see 2 of the three PLC on the switch, but this Flex I/O nothing. please. Trying to do a class Darren .M

Hi, I'm a technical institute student at Hydraulic systems technology , how can I figure out the latest things in my field,

very nice tutorials. thank you sir.

What size dry wall did you use for the wall and ceiling?

Great video. I'm going to use the template trick too and not eyeball and get it close. For the record I'm a Gen X.

Thank you for this amazing free education professor! Trying to learn as much as I can about hydraulics to prep for an upcoming forklift mechanic interview, and this was gold.

How long did it take you to get down to the studs?

Very helpful, thank you.

Thank you for the very detailed video! Super helpful

What if it was wired with wetted voltage? If the output is sinking, the power goes to the bulb, and then to the output contact.

Holly chit Gen Z guy...I don't know about you but I can pencil a mark by eye and install the lights and they will look beautiful..

I had 6 outputs from a plc, these are nozzles that were opening accordingly as programmed. However, after some times the began to operate inappropriately. Instead of opening and closing sequencially as programmed, they began to open and close in a wild manner, what could be the cause, any idea on what i should do?

This is one of my best videos. Thank you so much. Please, help and make more videos on plc troubleshooting. If you've link to other topics on plc troubleshooting please , share with me. Thank you again.

by metering in you could get springback, right?

Thank you so much, just have one question regarding the 80HZ setting: can the VFD output in general exeedes the max operating freq of the motor and how does that affect the motor?

Report back to the bosses lol that had me laughing my ass off! Just move the output to another open spot or just add another 120v output card. PLCs lose Inputs and output all the time. Don't make a bigger problem than it really needs to be. If you know the bulb is good, go straight to the output and check it there.

which application are you using

Can I use a reed switch instead of a limit switch?

Awesomeness THANK YOU for sharing, sincerely appreciate your time!!!

Thanks 👍🏻

Good day, sir. may i ask what is the name of this application that you are using? thank you very much!

I could be wrong but I think the K is what they use outside the US as a symbol for some sort of coil.

Thx so much. My partner tore down wall all at once weeks ago and it's was a tedious clean up digging out lath from plaster.

Thanks! First video that came up in my search and has everything I needed to change the fan direction on my Oh Sung microwave!!

Does this book have related videos for each section?

Great walk thru video and narration.

You don't change the old electrical wires out?

Very good explanation. I like it. Thank you so much for your informative tutorial.

Great and simple explanation. Can you tell me the name of the software you used?

Great clip .New friend to follower.

Finally, Time to make a suit of powered hydraulic combat armor.

Thank you!