Is the transfer case bolted to the cross member?

heh its funny, I had a stink bug living in my box too.... @4:20 in the very top left corner hah

Those are some strong bolts

I just learned a few things. Thanks

Get a bottle of water for that grounding rod. Easiest install you’ll ever do.

Idk but I'm pretty sure if that's a sub panel the neutral and grounds are supposed to be separated

Yeah good idea tunnel under the concrete 🇺🇸🇺🇸🇺🇸🇭🇲💪💪💪

Man the calculations were wo confusing. So why did you divide 2 by 12 again? Thankd for the video

Great Video - Exactly what I was looking for. Thanks

good job. thx for video

Wont the smoke that comes out of that rise and coat the entire siding black. Thats gonna look horrible if that happens which i dont see why it wouldnt

They run these saws at the factory to test emossions you are to late it has been ran hard already

If the gear puller isn't working for y'all, have patience, leave pressure and soak in penetrating fluid, then heat really hot and use the gear puller while taping around the cv joint with a hammer with an impact. Got mine off at 200k miles. It's doable with patience

Thanks for the tips man! I went n got a boat winch cause of your video!!

They do make caps already. Curious why you are using Formadrain for a slab foundation?

Those break out pieces are supposed to laid inside the openings in which they were broken from according to my engineer. I'm doing a block wall to fix my about 34 feet of my foundation. My engineer and the block company guy who's been in the business for 40 years - both said those break out pieces should be laid in the blocks holes.

Makes no sense to drill holes in a 2x4 shed wall. Surface mount would have been much better.

Please just take this video down I can’t believe I wasted my time watching this shit

What brand of laser are you using

Very good information. Thank you.

Great video, thanks. Wasn't sure which way that joint faced as they don't come with directions and the old one was unrecognizable. Much appreciated.

Why not use Helix micro rebar instead of rebar and mesh at 9lbs per cubic yard?

can you answer a simple question.?? why do i see ground wires and neutral wires both attached to the same bar sometimes.. and other times.. they are separate??

I like mule tape

Very helpful thank for the recipe great instructions to follow

What is the size of the door?

Waiting on doors

For our 1000sq/ft cabin upstate NY, the person did an excellent job adding sistering jack repairs recently but the bricks sunk and its sagging again in the middle We debate pulling the floor, to be able to actually dig down and set frost line poured footers. Would that be the proper approach when the jacks and cribbing just want to continue sinking?

The joiners don’t have two levels? So earlier you said it’s great for separate radon and water channels but now here at junctions it all becomes pointless does it? 6:29

I have to move a 8 x 12 shed from my neighbors lot over to mine. I believe this will be how I will do it. A lot easier than jacking it up 30 inches onto my trailer. Hopefully my 1025r John Deere can handle it like your kubota did...😊

It is hard to believe they don't make a cap. This guy's need to cap makes sense of course. A plastic plug makes best sense

If that is all you weren't happy about I would give the product high marks

A piece of composite decking or scrap Azek can be used as and end cap. This stuff is interesting and makes a lot of sense i like the fact you only have to handle it once the leave it in the ground perfect for a footing.

You gotta separate the neutral and ground 😂

Thanks for the video ! Please comment on your follow up reapplication of gun oil. I assume it will be like hand cleaning. Less is better !

grount and nutral same bar?

Or ... you could follow the break-in instructions in the owner's manual. The engineers who designed this stuff might have some insight.

Hello sir, I just saw your KZbin channel. There are videos in your channel and video quality is good but Title, Description, Thumbnail, Social, Checklist, and SEO quality are not correct, so your videos are not ranking well & your KZbin channel is not growing. If these issues can be optimized, hopefully, the videos will rank better & grow your KZbin channel.

I am confuse did you measured from bottom of subfloor to the top of the joist cause the laser level is not on top of the joist on the start point

I wish you lived closer so you could help me with my project. I am a one man gang.

Incredible information, thank you!!!

BEST video on leveling a floor. Great job, thanks!!!!!

Thank you

Rebar?

So the wall insulation can touch the insulation?

What doesn't make sense, is you ohming out the L1 and L2, it shouldn't matter what phase you're using to power up the unit. As long as a CT's are hooked up to the phase thats being monitered.

You missed showing the most important part of the motor bolt🤦‍♀️

Cut a wood block to size for placing all the bolts at the right distance .Make it tall enough to get all the bolts at the right height.

Didn’t tell the amount of oil needed

Think it would be better structually to taper the top of the sub fascia and bring it up to the top of the rafters.😮