Great job

What if the tabs do not come out?

You get an A for persistence. I had to grin when I heard you say just tap it on with a hammer... I did this on my Focus a few years ago and even with a press it wasn't easy. I've seen the 1A Auto video that has to be edited and leaves out the hardest part with this bushing. I opted for full arms with bushings for my Flex. Thanks for posting the truth.

I can’t stand Ford Engineers

Best video for cars in a long time. Also appreciated the way to test the valve. It gave me peace of mind to replace it on my own. Even if that was not the entire problem, the air coming through the valve by my blowing air, certainly is not a good valve.

Great job

You're very great at explaining your steps and everything, thank you!

I just noticed you called every peice the rack you have the window pannels and the Shelf. Didn't notice that the first time lol 😂

Hello friend i have the same chainsaw but the recoil spring is not workingdo you know whats the part number to buyit please

Saved me on the heater actuator, now you’re saving me on this u-joint. Thank you!

Bro best vid ever. So informative well spoken great discription. Way too go man you did a gret job on the video your 100% right about work boots and how to treat them. Keep up the great work dude.

I’ve seen a video where the sensor connector is unplugged and slips through the centre of a 22mm Ring Spanner . It would give a far better purchase to release a seized sensor. In my experience a “crows foot” spreads and slips. Also using brake fluid as a releasing agent helps unscrew seized threads

Why not take a few extra minutes to pull apart the caliper and clean and regrease the ‘ears’? And why not open the bleeder a little to make it much much easier to push the pistons? Why just slide new shoes in? It only takes a few more minutes to do a much more thorough job. Perplexed.

Great video. I needed to change the front tires on my Craftsman YT3000 riding mower. What a coincidence you posted a video on the exact same mower that I have!

I replaced that same actuator and still having that same one sife heat and one side cold it didny fix anything for me

Or balm????

What kind of conditioner were you using on ur boots????

In this video you talked about safely supporting your car with jackstands and putting the tire under the car for added safety. I gave you a like just for that.

I cussed many times working on that upper bolt. Meat hooks for hands.

Shouldn't you grease the slide pin?

im getting clunking noises on the front. i cant stand it. im getting the pieces i think it is and maybe the be the bearing also. hope it works. I appreciate the video .

I have a 2014 explorer 4 cylinder with the same problem but mines is not located on top

Gyatt

So I had a leak on the floor of the passenger side of my 2014 explorer. Hadnt even driven in days. Could this be what caused the leak?

My car blower constantly turning on and off. Does your car do the same thing? When AC and heater the same thing, on and off

Im having the same prob with my g35, i think it happened cuz all the rain and i dont have an under tray

You turned sway bar stud the wrong way. You tighten while holding nut with wrench. Wondering why you didn't explain that once you figured it out?

Need one for second Gen !!!

How did you know which one needs changed?

Thanks for the video. Just curious how long total it actually took you. Also, do you have the motor craft part # that you can share?

Thanks I needed this

You might want to check your underwear at 13:32

Part number

Great thanks, got a similar/same problem. Feels like when an old-school steering leaks out too much fluid, it jerks. Got to try this.

I got gas, and then my car would crank, but not start after that fill up. Since then I have tried to figure out everything on my own because I can’t afford to get it towed but the issue I believe is this solenoid. So my question is, could a bad solenoid cause a vehicle to dump fuel out straight to the ground when filling?

To put it on, just spray with wd40 and use a dead blow hammer... I've done hundreds of em and it take about 2.5 mins to put the new one that way

So I had the same issue for a while and ignored it. Now heat doesn't come out anywhere. Is that still the blend door or some other deal that needs help?

What sz tires are in there in this video ?

Thanks

Just installed the Rago Center shifter Console Molle Pannel Setup with the bridge freaking love it 15:31

Looks good Way more Organized

Love my rago Window Pannels Just can't find a Shelf 5:53

Wish I could find the shelf they No longer make the shelves 1:30

Thanks for the video...my interceptor utility just started having this issue...looks like I have a project for Thanksgiving

Thank you so much for the video! damn Dealership wanted close to $200 for a $40 part that takes 15/20 mins to fix

Should lift up bar and tighten nuts

Tube work is the hardest stuff to work with especially for someone who hasnt messed with it.

Nice work. Do you think I can stick weld this?

Very imformative. The device you made works I done the same one or two modifications realy easy well done.😊

Thanks for the vid!