Beun de beunhaas. koop goed gereedschap man jezus.

How much Newton meters for the block?? And what oil do you use for the clutch disks?

Haha id hate to have a engine rebuild via you should use the bearing extractor

Jaka dysza głowna w tym gaźniku

thats not how you mount bearings, heat the casing up enouch next time, they schould slide in or go in with light-medium pressure. and if you need to tab them in only hit the outer ring

Hi, I saw in the previous video that you repaired the entire engine for a Honda mtx 125 JD05. It's great. But I can't comment there. My question is how did you get the list of bearings and oil seals for the engine. I looked for it almost everywhere, but to no avail. Can you send the NTN manufacturer code, size or anything so I can find it. I'm really looking forward to your response. Thank you!

maybe if you ported it out you would have gotten more power, but you didnt port it and left the stock carb and manifold in, its garbage tbh, i know the parts are rare, but porting on these engines gives 2 - 3 hp, i had the same bike and i done it, theres lots of thick metal and thus porting is easy and safe, you didnt port it so im pretty sure you like men.

did you have to run a higher spec transmission for the power or did you use the stock setup? Thanks

WAAR de Fuck BEN JIJ mee bezig gast

ile i jaki olej wlales do skrzyni?

good job but next time hit only the outside of the bearing and heat the cases more! also dont hit the crank like that just heat up the bearing. also you forgot the locking washer on the clutch hub, just for next time you biuld an engine reminders

Why isnt my clutch rod going all the way in can someone help me?

Mit wie viel NM werden die Motorschrauben fest geschraubt ?

What are the two hose stoppers connected to the piston for?

Hi ,What is a oil capacity for thé gearbox?

Waar heb je de technische tekening vandaan ?

Hi im from 🇬🇧 I've git a motorhispanhia 2008 just put big bore kit on it with racing carb 90cc head im looking for plastics and a seat for the bike,could u help any sites to get second hand parts off please,tia

thank you for helping me to find the coil and battery, thank you very much😁

Привет, помоги запчастями

Does 50cc crankshaft and 80cc crankshafts are the same or the 80cc have something more????

where did you order all the parts for the Honda mtx?

Is dit een team of de gewonen

Never ever hit the end of a crank ffs 🤦🏻‍♂️ and I didn’t see you time the balance shaft up with the dots

a where masa wire you put?

it runs but doesnt drive :D

Za dużo młotka i uszkodzone bieżnie 🤦🏻‍♂️

Heb je de brommer nog ?

have the same cylinder kit :)

Im gonna try to fit that rear to a rieju mrt that has swapped engine from suzuki ts 125, wish me luck

How much does it cost to build one of these ?

poorly assembled, crankshaft mustnt be hammered on

Transfer ports matching? Measuring and adjusting squish clearance? This engine maybe looks good, but it will never run at 100% of potential this cylinder kit has.

Le phbg avec un 80 malossi ca fait petit. Surtout que les plus gros phbg font 21

Thx broo

Bro using 2 stroke oil in the gearbox.

Martellate sull albero e via

Według mnie głupotą jest walenie młotkiem we wszystko co się da przy składaniu silnika, a tym bardziej w wał, który może się zcentrować. Po odpowiednim rozgrzaniu wszystko wchodzi w siebie jak w masełko. Nie potrzeba żadnego młotka!!! To tylko moje zdanie. Osobiście nie polecam tego filmu jako wzoru przy składaniu waszych silników oraz tego Pana jako wzoru do naśladowania.

stop the mechanics you never tap to enter an object even less on the crankshaft and there is a squish to respect

Very nice video! This video gonna help me so much😂

kasikybäne malossi

Was für eine Übersetzung hat eine derbi senda drd xtreme um originalen Zustand (Bj 2020)

Schönes Video Jedoch eher Midrace. 80 MHR Replica.

I have my derbi senda 50 2017. Water pump leaked and lost all the coolant. It of course heat seized once and locked up. I got some water and fired her up, that was enough to get me to my destination. Problem is i have exhaust fumes coming out of my coolant tank.. so im thinking the head gaskets blown. Ive never done any major work on bike engines but i know how they work. Im an engineer. Now, i suppose i should take the engine out, take the head off and have a good look around, see if anythings warped from the heat. So on. Change the gasket. Replace the water pump and chuck it back together with common sense and knowledge. Would that be far enough to get her running proper. Also can the maintenance manuals be found online if i get stuck? Is this something i should be able to do relatively easily Any specialist tools required. Bike is all standard

How many gears in this bike🙄☝

Salut ! Comment et avec quel produit à tu enlevé la rouille sur tes jantes ?

how much do you buckle the engine?

how much it cost? (the parts)

Mit wieviel NM hast du die schrauben bei 5:12 angezogen?

in first two minutes you use open flame and a hammer, all against motorcycle repair principles

what was that blue stuff you put on the screw?