When you turn the engine by putting it in a high gear en turning the backwheel, wouldn't it be best to turn the wheel backwards for then the camshaft chain will not push in the chain tensioner ? Normally the engine drives the wheel and when you do it the other way round the camshaft chain tensioner will be loaded with torque when you turn the wheel forward. It is possible that the timing between camshaft/valves and the position of the piston is not right.
@kman2220 Жыл бұрын
Thank you for a perfect demonstration! I just adjusted the clearances on my V85TT. The right cylinder exhaust valve clearance needed some adjustment (it was a bit tight), but the rest were pretty good. Quite a bit more valve tapping then I remember when I started her cold (expected I guess since I increased the clearance) but I think I'll have take her for a ride before making a final judgement.
@robertpierce1981 Жыл бұрын
This video makes a Ducati valve adjustment look like the worst operation ever. MG made this easy
@raymondcoughlin79652 жыл бұрын
one more Q: should you check the right side as well?
@raymondcoughlin79652 жыл бұрын
Hi Hunter. Can to tell me when you say #4 for intake and #6 for exhaust, is that the same as .10mm and .15mm? 20007 Norge 1200.
@hhjones93932 жыл бұрын
That is correct, 0.004" is 0.10mm and 0.006" is 0.15mm
@gizzyguzzi2 жыл бұрын
Doesn't the Norge have a plug to see the flywheel marks with S for left and D for right? Or maybe hard to get to with fairings? That's how I always found TDC. Guzzis are so easy to work on.
@hhjones93932 жыл бұрын
No, it doesn't. Even on the bikes that have that I only use them for timing and that's after I verify the marks with a timing wheel. Sometimes they are off a bit!
@gizzyguzzi2 жыл бұрын
@@hhjones9393 well. they are only 'off' a tiny bit. Clearly close enough to find the top of the piston, Then it is easy to find the top by looking at the tappets. Much easier than spinning the wheel all the way around blindly, anyway...
@gizzyguzzi2 жыл бұрын
How do you change the inside pair of spark plugs? I didn't even know they had them
@spydie3 жыл бұрын
Why don't you adjust the tappet with the correct feeler gauge under the tappet?, Tighten it when you have the feeler under the tappet. It saves a lot of trial-and-error.
@naps33863 жыл бұрын
NGK specifically says NOT to use ANY anti-seize on their plugs. NGK plugs are treated with a trivalent plating that replaces the need for anti-seize or lubricant.
@bikeaholic63863 жыл бұрын
Wow, how simple was that? Thanks for sharing and taking the time to do this, it's much appreciated 😊
@hhjones93933 жыл бұрын
Thank you!
@henndawg420693 жыл бұрын
Thanks for the video. How did you turn the engine?
@hhjones93933 жыл бұрын
By the rear wheel
@henndawg420693 жыл бұрын
@@hhjones9393 Thanks for the reply. To confirm - you rotated the rear wheel to turn the engine? My 2011 V7C didn't come with a center stand. As such, rotating the rear wheel will be a problem. Should I have any caution or concerns with respect to turning the engine by turning the alternator? AFAIK, I rotate it clockwise, right? Is it OK to slightly rotate it counter-clockwise if I've just gone past compression TDC?
@hhjones93933 жыл бұрын
@@henndawg42069 Yes, you should be fine rotating it that way with both plugs out.
@henndawg420693 жыл бұрын
@@hhjones9393 Thanks :)
@aaron21763 жыл бұрын
Hello there, I have to tell you that you make a lot of noise when you throw your tools on the floor everything ells is OK.!
@robertsmith92993 жыл бұрын
No timing mark for TDC?
@hhjones93933 жыл бұрын
Nope
@Deetroiter4 жыл бұрын
I’ve been done a valve adjustment before but I want to do it myself because how else would I ever learn, and also don’t want to pay huge amounts of labor. Thanks for the video! I have a 2010 v7 will it be similarly method? Also, when going to the other engine head, will the intake and exhaust switch sides so that intake is closed to intake and exhaust is closest to the front or they don’t change at all on heads? And how important is it to synchronize and reset the tps?
@hhjones93934 жыл бұрын
Thanks for watching! The intake is to the rear on both cylinders so as you are facing the other side they would be reversed. The V7 is very similar but you will need to find the correct specifications for the gap, it's probably different than mine. The sync is a good idea but if the engine runs smoothly it's not the end of the world if you don't do it. Also, TPS reset is more related to the throttle sync
@cessnatpa4 жыл бұрын
Wow that was amazingly quick and simple procedure. I'm thinking about buying a Norge and wanted to see what was involved for the value check. I own a Ducati Multistrada and wouldn't even have the plastics removed before having both sides done on the Norge. I want to buy one now so I can just do a valve adjustment under a hour.
@hhjones93934 жыл бұрын
For those that have commented on my torn valve cover gasket it is still on the bike and not even weeping! Just lucky I guess.
@nikitis134 жыл бұрын
Another reason why Guzzi owners buy Guzzi's, beautifully simple. Potentially a morning coffee job and a ride out for breakfast... Now lets see a Ducati owner get that done with a timer... LOL
@OAK_MTN3 жыл бұрын
exactly what's drawing me to them. One day I'll own a Griso.
@jamesnickel47485 жыл бұрын
Hey man, thanks so much for this...quite simple! All the best!
@hhjones93935 жыл бұрын
Thank you! Glad you found it helpful.
@jamesnickel47485 жыл бұрын
@@hhjones9393 very very helpful thanks again!
@SuperGinkgo5 жыл бұрын
Fantastic vid m8 many thanks
@hhjones93935 жыл бұрын
Thanks!
@dangravante29065 жыл бұрын
Which torque wrench are you using? I'm looking for one, and the one you're using, seems like you trust, so that's the one I want. Thanks.
@NickStaib5 жыл бұрын
Nice one! When at the end you said, just one last thing (and dropped the gears back down) I thought you were going instead to reach for a clean rag, and wipe the grease off that otherwise sparkly cylinder head! Am I right in thinking that the it would be the same sort of procedure on the new V85TT?
@hhjones93935 жыл бұрын
Nick Staib Thanks Nick. I haven't seen the valve gear on the V85 but I'm sure it will be quite similar.
@Hansengineering5 жыл бұрын
Did this hundreds of times on the RQ-5A Hunter's "V75 Hi-e" engine. Extremely similar. Lots easier to spin the engine with a propeller, though.
@gregorytimmons47775 жыл бұрын
Just one reason why i love Moto Guzzi. Ease of maintainance. Easy valve adjustment. Trans. that pulls out of the rear of engine. If only that oil fiter wasn't inside the sump. I don't need the fastest bike. I need one that is built to keep me riding and is easy to fix when something does go wrong.
@hhjones93935 жыл бұрын
Gregory Timmons i can't disagree. The Guzzis are a lot of fun and pretty easy to take care of. The newer big blocks even have external filters.
@LaurieWilliams-lk8fc3 жыл бұрын
Oil filter inside sump forces inspection and noticing anything that should not be in there, including small bits of gaskets or other seals.
@Av8tor5015 жыл бұрын
Hey Hunter, when are you going to do the sychronization and TPS reset video? Thanks for the good VA video!
@hhjones93935 жыл бұрын
It still may happen! I just haven't had time to figure out all the photography and editing yet.
@Av8tor5015 жыл бұрын
Hey Hunter, when are you going to do the sychronization and TPS reset video? Thanks for the good VA video!
@hhjones93934 жыл бұрын
I think that is coming soon, the current state of the world has left me with some free time!
@shmac965 жыл бұрын
That was fucking awesome! Thank you sir!
@goransablic73395 жыл бұрын
Very useful video indeed.
@Av8tor5016 жыл бұрын
Great video Hunter. Still looking for the synchronization and TPS reset! Are you still planning to do this? Would love to see it if you are.
@braaperino4516 жыл бұрын
Hes not straight, NOR GAY. not norj lol
@hhjones93936 жыл бұрын
Braaperino Depends on where you’re from. Norge is pronounced differently in many languages. I am familiar with the pronunciations in Italian, Norwegian and some others. Most every Guzzi owner I’ve met knows how to say the name as the Italians would. But I’m speaking here to a primarily English speaking audience and so use that pronunciation. When in Rome.........
@davidchapman35636 жыл бұрын
I have a short fuse and ive found that taking a break from whats irritating me and come back like u said.but when working on motors i have to keep going untill i get it right
@jlfm91026 жыл бұрын
Great vid and thanks for posting! Just a quick tip to anyone reading this - instead of a piece of wood, maybe use a drinking straw or something that won't accidentally break (or fall), so you don't end up like this guy (bit.ly/2iDFQf8), this guy (bit.ly/2jspGWv), this guy (bit.ly/2BdQDaW), or me.
@Av8tor5017 жыл бұрын
Great video! I have a 2008 1200 Breva Sport. Same procedure & specs I assume? Also looking forward to your video on synchronization and TPS setting.
@hhjones93937 жыл бұрын
Yes indeed, same procedure. I would suggest verifying the clearance for your model though.
@ultrasardine7 жыл бұрын
Nice work. +1 sub
@giomas747 жыл бұрын
Great tutorial... just a question, is it possible to use the torque wrench also for the register nut?
@hhjones93937 жыл бұрын
Thank you! Yes, you could use a torque wrench on that nut. Most people do not because of the need to control the position of the stud to achieve the proper gap.
@markstirling48557 жыл бұрын
Excellent Hunter. Good steady camera makes such a difference.
@hhjones93937 жыл бұрын
It's steady alright! It was on a tripod. Wiggly video is a distraction to me too.
@konstantinosva42737 жыл бұрын
i like bikes that they are easy to maintain , most bikes needs to remove the fuel tank before that
@alandmorley7 жыл бұрын
top man gr8
@lornescott-wilson61447 жыл бұрын
Reminiscent of BMW boxer airhead valve adjustment, especially since it is a 2 valve. My R100RS looked the same. To find TDC on the airheads you used to be able to pull a rubber grommet off the side of the engine and see the flywheel and look for the OT stamp (line it up in the middle of the inspection hole). Check which side had loose tappets and then roll the engine over until the OT came around again and then it was ready for the other side. I have an R1200RT and even now, though it has shims, I still do a similar procedure to what you do on the Guzzi (but no quick adjustment, have to replace shims if required, but they pretty much never need replacing anyways) Nice work :-)
@hhjones93937 жыл бұрын
The Guzzi twins with a 4 or 5 speed do have a timing plug in the flywheel housing like the BMW. Good for verifying position.
@roadwraith67 жыл бұрын
what do you see going wrong on this engines? I have a 1200 Sport 4V 07 with 40000km on it now And could not be happier. Just want to know what to look up for.
@hhjones93937 жыл бұрын
These are pretty well developed engines, the basic design goes back 50 years. If you are doing the maintenance and riding it regularly as it was intended (briskly!) then she will reward you with many years of joy!
@giumbolorossonero7 жыл бұрын
Hi. Great video. English is not my language: would you please be so kind to write down what are you doing since the very moment you get that stick (from around 4:25 on): my understanding is not that good, but I'm sure It'll be better by reading it. Thanks a lot!
@bensfideos7 жыл бұрын
He's advancing the piston to Top dead center before making the valve adjustment by moving the rear wheel of the bike. The transmission is in 6th gear. So he put the wooden feeler gauge in there to help me identify when the piston is at top dead center.
@nuggethead0087 жыл бұрын
Great video! I just got a 2013 Griso and would like to learn how to do this procedure but alas....I'm not at all familiar with how to find TDC. If you ever get the time, could you do a "basics" video on the principles behind what TDC is and how to ensure it's at the right place before an adjustment?
@aleksanderkurilenko45887 жыл бұрын
Is guzzi quality over all is good ?
@joefazio49957 жыл бұрын
Having owned 7 of them I can tell you, YES< they are high quality, easy to work on and VERY reliable. I have also owned Harleys, Yammies, Kawis and Hondas. To me, the Guzzi is the best bike I have ever owned.
@txrx45147 жыл бұрын
Looks well designed and well engineered.
@gregorytimmons47775 жыл бұрын
Yes. Really couldn't be easier. That task anyway. Thankfully the whole bike is really designed so ease of maintainance is a common theme. If only the oil filter was not inside the engine.
@brunoumoffia60987 жыл бұрын
Awesome video. Very helpful. Thanks Thanks
@ripmax3337 жыл бұрын
wow easy peasy with these guzzi, very simple to do.
@kieranb1807 жыл бұрын
This is great man! I'm going to do this on my V7 this weekend. Do you need to do a TPS reset after? I thought I had read somewhere that this what the case.
@theodoreteo86468 жыл бұрын
Thanks for making this video with very simple and clear instructions. Kudos!
@PuyZ068 жыл бұрын
Excellent video. Thank you so much. Are you still planning to do video on synchronization and TPS reset? Thanks again.
@OtisENGINEuity8 жыл бұрын
it amazes me that they are still a flat tappet design and not a roller or hydraulic or anything. I guess that could be part of the limiting factor for the power. I know part of why Ducatis make so much power is that they run no valve springs and the valves are actuated mechanically. Weird that they are still the way they've always been though.
@Wheels_Unlimited8 жыл бұрын
It's a huge flaw in the older Guzzi engines that causes a lot of problems. At least in the Stelvio they changed to roller tappets in 2013.
@OtisENGINEuity8 жыл бұрын
The Raconteur it's not a problem if you know about it and maintain them correctly, it's only a problem when you get people that have absolutely no mechanical knowledge that will ride it into the ground and never even take it to the dealership and get it tuned up.. I probably wouldn't have any issues because I've been raised around classic Triumphs. I don't know if I could fit on one though being 6'10 with barely a 30 inch leg inseam.