Check out DTA Triple rod holders

Good stuff bro!

Nice

Let’s freaking go brother❤❤❤❤🎉🎉🎉🎉

Hey! You probably don't remember me but we worked at sports seasons together a little when you were in high school lol. I ran into Mary the other day and she showed me your channel! And I subscribed! Good work! I hope you are good and if you ever need editing help... that's what i do, specifically for the bass boating industry! Lol great work I can't wait to see what you do next!

Let's Eat 😋

And he was getting bit on the far left rod too! Bro went back to back to back

🤘🤘🤘

Very Nice Buddy!

Love the vids keep it up!!❤

Let’s freaking go!!!!!!

Wow what a sportsman.

Bro where can I get a fishing like yours brother

My adhd would eat me alive in a few minutes....if have to cast something;)

Catfish eat anything

Hello, I'm a really enthusiastic fisherman but my line keeps getting tangled. If you have any tips pls share. Ty

Goes fishing on a boat throws 7 rods in the water sits staring at the phone people fish for different reasons i guess

Bro is fishing all the rods he found in his basement 😅

"promosm" 😍

you had to cut it off?

Step 1-put the car on ramps.Flush the system,with new fluid.Another video. Step 2-Jack the passenger side up,remove the ramp install jack stand. Remove tire. Step 3- As a safety measure use a few block and a 2x4 to put under the passenger frame as a back up in case jack stand fails. Step 4- remove the 10mm 🔩 Bolt low supply. Step 5-16mm open end wrench for high supply line hose,disconnect. Step 6-Remove 1st power steering bolt 15mm with a long extension and swivel. Step 7-get underneath (your safe)with long extension and swivel go past driveshaft to get 2nd bolt out(pain in ass) or just feel for it from the wheel well with small extension and inch it out the 15min way. Step 8- rotate the now free pump so that the pulley faces you in the wheel well. Place a flathead screwdriver in the wheel and lodge it so it can't spin.Attach the puller and free the pulley (I use impact wrench on the puller bolt takes 10sec)Now the pump can be fished out from the wheel well with pulley wheel off. Step 9-reinstall in reverse order. Step 10-Check the filter in the reservoir,brake cleaner works good small amounts of its dirty,add a inline filter to the return line. Step 11-change the Belt if it's due, bleed the air out.2hr Job.2 people 1hr.Good video but not the easiest way.No need ever to drop the frame,removing the 2 heatshields underneath will work also fishing it out that way with the pulley on,by the driveshaft.

Was it all bolted on?

Where are you located at ? I’m trying to replace my radiator support

How much does it cost to install a radiator support on a 2013 camaro if u already have the radiator support part?

Cool video bro!

m.soundcloud.com/ianarsenault/tennessee-whiskey

Great video. Better than most of the other ones I have watched. Going to try this repair!!

I just finished doing it on my 2008 Saturn Outlook. Hardest steering pump I have ever messed with.

Thanks for a very straight forward, easy to understand video.

Dont have to drop subframe .. just remove the transmission mount and lower that side of engine and it will come out

I did the same thing today on my wife's 2014 enclave. However, in addition to lowering the passenger side engine cradle I had to lower both driver side cradle bolts also. When I was putting everything back together I had a minor alignment issue with the passenger side cradle bolts. Will lowering all for cradle bolts cause an issue with front end wheel alignment?

Thank u man this video is the best one for this job not like the one with the stupid black foo the make me take off the exhaust 4 nothing thanks man

What prompted replacing the power steering pump? I’m hunting down a low groaning/moaning noise that happens during acceleration. Mostly after the vehicle has come to a complete stop.

Its also for a 07 Saturn outlook thanks so much😊😊😊😊

is this AWD. i have to have the same done to my 2010 Saturn Outlook.

How long should the total job take including the pulley puller. Thanks

Remind me to never get a Buick unless it’s a 87 regal

Thanks for the video. I got the job done, but this was a miserable repair. Getting that stupid pump back in took me forever.

Hey just a fyi I had my traverse entire steering assembly replaced was outta warranty but it's a know issue and expensive

how did you purge or bleed the air from the system?

So you did not have to remove the right side catalytic converter?

Thanks for sharing body good job

How many hour would you estimate? Dealer in FL charging my father $1300 for pump and high-pressure line that they blame for pump failure! GRRRR I drove car just before it went to dealer and noticed hard turn at engine idle. Checked fluid it was low. Topped fluid and condition was same...low idle hard steering effort. Comment welcome.

thanks For the video thomas, now is time to get busy!

you don't have to lower the cradle. Just remove the two heat shields from the exhaust and remove it from the the back.

Is this a AWD or a FWD? the reason I ask is because im about to tear into my wife's car and I hear it is a lot harder then the FWD. Thanks for your time and great video.