Your english version is very nice.

Sir,when u are pressing the compressor discharge tightly with the thump finger, is this compressor off or not.how we can determine the pcb is working in good condition or not

thank you very much sir...

How to disconnect the charger line? Gas doesn't come out, compressor doesn't lose pressure?

Thank you for such a simple and clear video. I've ordered blindly everything that had "drum *insert your washing machine brand and model here*" in the description, 2 of each. Whatever I won't need, I'll just return with full refund. Let's hope it'll be only shock absorbers or springs, because I really don't wanna open the drum casing and mess with ballbearings (which obviously I've also ordered) 🙈

👌👍👌

$600 dollars !!! ?? you can buy 10 panels for that. it is better to just buy more panels.

Thank you very much from informations khalid from Morocco Casablanca

Bellissimo video tecnico, chiaro e utilissimo. Grazie!

Nosense! What benefit is it to the viewers, if you repair off camera?

Super tnx 😊

Love your video🤩! You have new subscriber.

Voltage on R108

What was wrong in the Board will be TOLD in the next video (link to the video will be provided when Uploaded)

Thank u so Mach sir I love you 💓💓💓💓

Worst explanation I've heard in a long time . . .

Nice

Useless video, waste of time....😢

What an appalling attempt at explanation. Lesas back and forth with assumption, mostly inaccurate desription and no coherent diagrams.

My board blinking 10 times, can you tell me what I should do. Regards🌹🙏

Electronics and Communication Engineering Graduate here... We have studied about Modulations in Analog and Digital Communication Subject in our 4th Sem... Well in case of PAM.. you multiply the 50% Duty cycle Pulses to the Analog Sinewave to get PAM output, then we use hold up circuits to flat up the top of PAM signal... You cannot multiply Rectified 230VAC with FBR(full bridge Rectifier), but can be done with BJT, MosFET or IGBT, but... That Switch is going to waste a lot of energy (in many cases upto 30-40% of output power, an it will be running in Saturation Region.... So here they are not multiplying the signals at all.. but using 2 FBR in parallel to handle more power, distributing Heat dissipation.... And using PWM modulation along with 50-60Hz Quasi Sine wave superimposed,it is done inside the Microcontroller onboard... And switched by IGBT or MOSFETs

Thank you very much from informations khalid from Morocco Casablanca

Teşekkürler hocam. Sağlık ve bereket dolu günler dilerim.

Very useful information .Thank a lot😅

Good job sir keep it up

Please Tamil

I have these same issue in the same pcb main filter capacitor is ok.the compressor is trying to increase and decrease the rpm in the running stage and when i am pressing the discharge of the compressor tightly with the thumb,the compressor off and error occured after some time.when i am not using my thumb on the discharge line compresspr work for a long time.i have these same error F1 also. Which are the components i need to check.pls help

👍👍👍

Impressive video, Forever Tech English. Eager to see your next upload from you. I hit the thumbs up icon on your content. Keep up the amazing work. Your explanation of the rectification process was particularly enlightening. How do you think the choice of diodes influences the overall efficiency of the power supply circuit in designs like these?

You ripped this video from someone 😂

Thanks so much for your update video

Good day sir,may I know the values of 8 leads ic, because our controller has burnt out,thanks

Thanks for the video ING, saludos desde Tepic Nayarit México

how to fuck up your soldering tip 101

kzbin.info/www/bejne/fZWsn4Z8pZZ4aassi=AORM24vy82ytVgOE

Follow your videos are expanding my horizons. thanks very much

Correction: motor speed control via triac uses phase angle control, and hence voltage on motor. Faster or slower pulses have nothing to do with phase control. Honestly, I can't belive you didn't say what those pulses are. Those are zero crossings of AC input voltage, for triac phase control. Dc voltage of 330mV doesn't mean anything in analisys of those waveforms.

Sir. What's the blower motor feedback frequency for this pcb?

Noooooo! It is just Pulsed😂 The ac is only in the starpoint of gen/trans... and 3phase against n.... but we never ever could one pole touched without this just pulsing on one cable❤❤

Thank you very much from informations khalid from Morocco Casablanca

❤❤❤عالی عالی عالی ❤❤ Ok❤ok❤ok Mohsen iran

Super explain sir. Thanks. 🙏🙏🙏🙏

Thanks for the information,very good.

Thankyou!!

So cute how he "checked" his pulse 🤓

It's not the other way arround ? P = Phase (Live) and N = Neutral ?

what was on the tin

Your nitrogen setup terrifies me. Don't you need a different sized capillary to convert this? Why not charge by observing the evaporator frost line?

How we can used injection voltage to reaching evidence micro control is faulty

You installed a new microcontroller. How did you flash the software?? you can't use new microcontroller as it is??