crosslinker?

Heya Dave. I have some rust on my metal shed roof where a previous rust converter application has caused the paint to flake away. Do you recommend sanding the loose paint away prior to applying the Feronite Rusty Metal Primer?

This is a brilliant video, it answered a lot of questions that I didn't realise needed answering lol!

A life-saver! As a newby, I would have absolutely f'd up.

If it is rusty on the top it is likely to also be rusty underneath especially around edges and laps. I think as I said in other comments you have to lift the iron and treat / paint rusted areas. My roof has rusted far more on the underside especially at the edges and in between laps.

personally i would have rented a 5 bag sandblast pot and a few bags of black beauty and brush blasted the bad areas of roof then blew it off with the blast hose to clean it. then rolled a good coat of iron oxide primer on it followed 2 days later by rolling a coat of white hi-gloss industrial enamel on it. you would have to come back 8 years later and wash it off with a powerwasher and soap , let it dry ,then roll one more coat of white industrial enamel on it to make sure you would get another 15 years out of it. the white reflects the suns heat and makes it much cooler under there in summers, and the hi gloss enamel makes snow and rain&dirt run off fast as it does off a cars finish. if you wanted to get 30 years out of it you could rent a sprayer and spray the underside with iron oxide when you primed the top.. no need to put finish coat inside.

What a mess

Did this work well I got a more serious case of broken pontoon and hoping to fix it

excellent advice i made this mistake ONCE never again!

You will be constantly treating it.

Rust continues to eat through to other side of metal it's best to remove &replace with new product. Covering it is only a temporary fix and a future nightmare to deal with down the road. Always best to do it Right the first time. Maybe Remove Rust and treat Before Screwing it to Rafter's.

How well would this work in making props? I'm working on a bat and tried to make a duct tape mold followed by spraying can foam in. The mold ended up spliting along the seam and being severely misshapen. Is there a way to estimate how much it'll expand?

I won’t to glue rubber or nolathene to steel to be used as a bump stop on a hot rod as I can’t get drill anywhere close

It actually looked worse from below once you got up on it it wasn’t that bad

Hi, thanks for the comparison video. Just wondering how many litres of lemon peel would you need to strip the antifoul from this boat?

Knowing what NOT to do ... Very helpful !!

great vid this is the info i was after cheers dude.

I dig the Pink Floyd in the background !!

Very helpful!

Would it just peel off the wood itself as well?

What/ how did you paint the roof with after the feronite?

Thanks man! 1:32

Do you sand the feronite before you paint? Thanks in advance :)

Not very helpful. What does it do? What is the final result?

Good. Glad to know this!

where to buy pouring foam?

That Marching was Awful and Sloppy. But everything else was great ! Nice Flag ~

Hi mate, Thanks for the video just a quick question can I spray Feronite under the car? I’m not sure could damage the electronic or plastic materials? Thanks

Hi mate, Thanks for the video just a quick question can I spray Feronite under the car? I’m not sure could damage the electronic or plastic materials? Thanks

Where to buy feronite in store or online? Based in Adelaide Thanks

Hello, our company is leading recycler of plastics in India. We have Tonnes of peel ply waste. It is impossible to remove the resin or the silicone coating from it. Is it possible to provide any solution for the same? It would be a great help for us.

what do you recomend painting it with after / on top of the feronite to protect the feronite from UV, i have a big garage roof with a fair bit of rust so want a good cheap solution , looks not important to me. and thanks for a great video

Is the converter ingredient in Feronite Rusty Metal Primer the same as the ingredient in Feronite Rust Converter? Is the shelf life same for both?

My caravan door has fallen off its hinges on the bottom. The top is hanging on for dear life. I know nothing about renos. Dya reckon I could put the goop in the previous holes and then screw new brackets on? Or would that not hold? The caravan was probably built in the 1970s/early 80s but I need it to keep living for a few more years to house one of my teenagers. If you see thus and reply, THANKS, MATE

​ @The Epoxy Guru - Tips & Tricks Does it matter if you haven't sanded off all the paint from metal? ie. will it have some adverse reaction with any paint left on the metal?

I used this on my roof, worked BRILLIANTLY. Couldn’t recommend more. Painted over the top a year ago, no rust!

Looking good there mate 😅

How long has it taken a beating I am wondering how it doing now

Useless! Never actually show if it worked!!? Wasted my time!

So what happened after this?

That's a fair dinkum Aussie giving you a run down

I have a project where I need to fix a cut rubber tyre to the steel rim, how can I achieve it please help me get an idea

Is this like Evaporust?

old vid but just what i was looking for, couldn't decide weather to use body filler, weld it up or epoxy for 4 small holes in my camp trailer. The tape under the hole and epoxy worked great after rust treating it.

Ive used Bote Cote for timber restoration on heritage windows doors and sills. Mainly to seal raw timber after rot has been removed then as a adhesive when I scarf in new timber repairs (non structural) and as a filler prior to painting. Its worked very well, what your thoughts on this. I have a large restoration coming up and wanted to use Bote Cote.

Thanks for the tips. I want to fill boat cabin walls with it;

Learning curve, thank you

Goo Day, just one question: do have to wask off with water after Primer is dry?

"Faom"

Peel play using glass over glass, thanks mo