C10 Thrills

Пікірлер

@robertboyero3797 6 ай бұрын

Where did you source those clips from? My kit only came with stick on clips and they suck.

@C10ThrillswithViekerHill 6 ай бұрын

@@robertboyero3797 you can get them on ecklers. The stick on one's are terrible. I'll send you a link

@C10ThrillswithViekerHill 6 ай бұрын

@@robertboyero3797 www.ecklers.com/1969-72-chevy-truck-upper-side-molding-clip-set-fleet-side-short-bed-61-278783-1.html?T5_Var2=shopping&Chevy/GMC+Trucks+(1947-2000)+Vehicle+Medium+LTVMiddle&intl=0&dialogtech=ppc&gad_source=1&gclid=CjwKCAjwnqK1BhBvEiwAi7o0X4LUV2Ml9HWDekbVJBG9UkHSxH94EmXo-UjEFXJq-bl50QwBkcabVRoCWzwQAvD_BwE&gclsrc=aw.ds

@robertboyero3797 6 ай бұрын

@@C10ThrillswithViekerHill THANK YOU!

@C10ThrillswithViekerHill 6 ай бұрын

@@robertboyero3797 no problem. That's the top set. I'm not sure if you need the bottom too.

@josejimenez-sy5pd 7 ай бұрын

Looking good thanks

@danielviorato1333 10 ай бұрын

Hey my friend can you let me know what clips did you get with your upper bed side trim because I got mine and it is to big won’t fit on the trim

@danielviorato1333 10 ай бұрын

Hey my friend how many holes did you make on the fender on door and bed side can you please let me know I’m doing it on my 71 short bed

@danielviorato1333 10 ай бұрын

and how much space and between each hole

@danielviorato1333 10 ай бұрын

One more question what size drill did you use for upper and lower thank you nice work

@thebosshog2637 11 ай бұрын

Any idea how to fix the gap between the column and steering wheel?

@rickymartinez3518 Жыл бұрын

What size tires and rims are those?

@C10ThrillswithViekerHill Жыл бұрын

22x9 front 22x10.5 rear

@gibbsscott Жыл бұрын

Hey man! Thankyou for the video! Getting ready to do my trim this weekend (hopefully!) I was curious, what size rivets did you use to hold the trip clips on the cab? Thanks again!

@C10ThrillswithViekerHill Жыл бұрын

No problem. I don't remember the exact size but 1/8" x 5/16 should do it. Get aluminum ones.

@VictorTorres-co7wv 8 ай бұрын

Hi great video I’m getting ready to do the same thing, where did you get the clips? Thank you

@aaronhoughtaling6829 Жыл бұрын

Great video. Thank you for taking the time to put it up and show how this works. I’m getting ready to redo the top of my cab. Address surface rust at drip rails and redo seam sealer. Going to paint the top of the cab white to hide the area of repair. My truck didn’t originally have that trim and you made it look easy to install for truck without it. One note I’d suggest for anyone else is dab of paint where drill the holes before installing the screw or rivet. Just to help with exposed bare metal

@C10ThrillswithViekerHill Жыл бұрын

Great suggestion 👍. Thank you for watching feel free to reach out for any questions.

@deankay4434 5 ай бұрын

A popular product for a seal on screws or pop-rivets would be 3M Auto Bedding & Glazing Compound. P/N 8509 and comes in a standard caulking gun tube. Designed for sealing rubber to metal, glass to rubber and I even used it on front lip of inner fender panels where it bolts to the fender. This area can never be cleaned and always collects dirt, dust and perhaps starts rust. I use tons of seam sealer but I spray epoxy as well on bare metal. Two nice coats seals it like plastic wrap on a steak. The “Glazing” compound is non-hardening and last a long time with the tube capped. Best of luck, thanks kindly for the video instructions!

@ryansmith2845 Жыл бұрын

Great video, Thank you Sir!

@C10ThrillswithViekerHill Жыл бұрын

Thank you 👍 and thank you for watching 👍

@carlosgarza1962 Жыл бұрын

Awesome job. Where are you located? Would you do this for someone?

@C10ThrillswithViekerHill Жыл бұрын

Livingston ca. Yes I do it for other people.

@chuck1607 Жыл бұрын

Do you apply a clear silicon before installation? When I removed mine I noticed there was some sort of caulk between the clip and the side panel. Thanks for making this video.

@C10ThrillswithViekerHill Жыл бұрын

On the door yes to keep water from getting inside. Bed and fender won't make a difference.

@tysonb209 Жыл бұрын

Did you cut the side trim? If so, how did you do that?

@C10ThrillswithViekerHill Жыл бұрын

The owner had a used set of short bed trim but I did have to cut one piece because it was missing. I'll see if I have some old trim and I'll make a short video for you to see how.

@tysonb209 Жыл бұрын

@@C10ThrillswithViekerHill dude that’d be awesome. Thank you!

@C10ThrillswithViekerHill Жыл бұрын

@@tysonb209 videos are uploaded 👍

@jesusisking9744 Жыл бұрын

Nice!

@hectorsaenz6118 Жыл бұрын

thank you very much bro.. was having a hard time.

@C10ThrillswithViekerHill Жыл бұрын

No problem bro 👍

@hectorsaenz6118 Жыл бұрын

why dont you show how to put the clips on the trim.

@C10ThrillswithViekerHill Жыл бұрын

Didn't think about it but thank you for the input I will definitely make a short on how to install them.

@hectorsaenz6118 Жыл бұрын

@@C10ThrillswithViekerHill awesome man thank you very much..

@C10ThrillswithViekerHill Жыл бұрын

No problem 👍 I uploaded the shorts on the clip install.

@waynemontes2737 Жыл бұрын

I have a 71 c10 two-tone blue and white

@waynemontes2737 Жыл бұрын

Nice job

@C10ThrillswithViekerHill Жыл бұрын

Thank you 👍

@CarlosHernandez-gn7fs Жыл бұрын

What brand is the trim

@C10ThrillswithViekerHill Жыл бұрын

Classic parts of America

@hawkynz Жыл бұрын

First trim video I've seen. I just two toned my truck and have the trim. Just haven't put it on yet. You made it look easy.

@C10ThrillswithViekerHill Жыл бұрын

Yea I noticed there wasn't any videos for this specific trim so figured it would help some people in the future 👍 just take your time and mock it up with tape first before you drill and you'll be fine 👍