Thanks ✌

I used same plug, they are do not leak

@@benp1059 They all the same size 14 mm hex I believe

Thanks

You are welcome. I don’t remember but it’s in the video. 238900 NORTHERN RADIATOR

Sorry, my bad Somehow I missed that part in the video. Appreciate your response!

3 3/4 socket.

Try to charge now and after charging, test the battery. The goal is to get results, not to flood the cell. If no change in battery- repeat the process.

@@DIYDime Thanks for the input. It charges, but drops down to ~12.2 within a few hours once off the charger. A lot of heat was generated, so thinking I'll repeat.

@@bradanesi3998Make sure you charge the battery with low amps. If you have infrared meter you can check each sell to see if they perform same temperature. If one of them will give high temp then the other one it could be shorted.

Hello, unfortunately I don’t know the code, because it’s newer style. Try to google it or forums.

Thank you for the response I’ll attach a picture of the codes I have on the suspension

C10D3F6 Level control system Left front boosting implausible. Active C10D3F7 Level control system Right front boosting implausible. Active C11D2F1 Front axle ride-height control system extremely low level detected. Active B200300 Function locked. Active C1046F6 Level control system Axle load determination not performed. Active C10400 control position not learned. Active

I really appreciate the video. You were very helpful

I believe I need to calibrate the vehicle but I’m not sure if my Autel will do it but I have all the options you went through on your end the only thing that didn’t work is the security code

In my case I had a water pump leaking, not a housing. Some people buying housing and changing housing too when they have only problem with the pump which is unnecessary.

@DIYDime It's not unnecessary. If the o ring on your water pump has gone flat then the 3 o rings on the housing will soon go flat as well. Doesn't make much sense to wait till later to change the housing o rings and have to repeat the process. I fully understand that at the time that it's only the water pump leaking but it would only take the removal of I think 7 13mm bolts to prevent a leak in the near future. What you're showing these guys is an incomplete job.

Glad I could help

As you see on the video, the airbag itself have three connectors, which is branches to only one connector that go to the steering wheel. Besides that the steering wheel itself have lots of connectors.

@@DIYDime yeah I see. Thank you I’ll be subscribed

@Quxesss Please subscribe if you could, I’ll be adding more BMW X7 videos as we go.

a.co/d/0csqxjk3

I found a german language PDF file, where someone from 🇩🇪 describing in details how to do that.

Thank you. This is welded clevis brake chamber, but some semis and trailers have different brake chambers people are cutting a stroke to make a shorter so it can fit for their vehicle. Unfortunately I don’t have a video how to adjust a brake shoe yet.

Sadly I couldn’t get my EufyCam 2 Pro to open with your method…

No I had to reboot I drive by holding volume button.

1 Liter or fill until it’s running out.

@@DIYDime how did you position the straw, I can’t seem to get it past the middle part

@@paxrom1It is soft flexible hose that connected to the soap pump.

If you charging your main battery which is located in the trunk you do not need to disconnect your auxiliary battery.

Thanks. I disconnected it anyways. Trying now. I haven’t yet been able to get the safety click like you in the video tho

I didn’t buy camera. I bought used overhead console of a eBay and pulled camera from there.

SL Euthtion 3000W Pure Sine Wave... www.amazon.com/dp/B09B5Y3MWD?ref=ppx_pop_mob_ap_share

Same as the other modules but you need to have correct file software (version).

What charger are you using? You need to set at list 14.2 volts on your power supply in order to deactivate safety switch. Check your battery terminals with volt meter and make sure it’s showing 0Volts, because if it’s not and your battery showing voltage then you might have other problem. Go to your I drive manual in the car and search for software upgrade or something like that and it should tell you exactly what procedures need to take in order to finish update

@@DIYDime I’m using the same charger as yours and I had it set the same as you do. 14.7v and 2Amp. I have the X7 as well.

When you test the battery with a Voltmeter what does it show? 0V or 12-13.2v?

@@DIYDime it is showing 0v with the output button being off. Then it will show 15v with the output button being ON. But, safety switch isn’t disengaging so Battery isn’t taking the charge.

@@DIYDime how much charge did you put in you L ion battery? I know you said 13.2 V should be the minimum, did you go above 14v to get the software to update?

Nice

$500, Kenworth dealer in Florida.

@@DIYDime brought my 2019 international isk15 last year had 604k miles I think it’s time now?

Sorry I have another video (water pump replacement) and I mistakenly thought you are asking me about water pump price which is $500. Valve adjustment price I don’t know since I did it myself

@@DIYDime oh ok gotcha

Febi

Okay but they dont have sprockets in their kits only chain and tensioners and are they good quality?

I did not change the sprockets! only the chains and tensioners! yeah, it’s a good quality also

Thank you but dont the sprockets wear and when they are weared and change with new chains dont they wear chain faster?

@@MartinManchev-bv3wt inspect them if they are bad change them also but otherwise you should be fine. I didn’t do it on my a8 and a6. Only chains and tensioners.

Great to hear!

Thank you! 😃

You need to disconnect both of your batteries before you proceed take the overhead console. No lights the only thing you will need to initialize your sunroofs. I have a video on my channel how to do that.

Yes

Is there enough room to work on upper arm bolts by just removing the wheel well cover, or is the air shock needs to be loosened as well?

@@dumitrumalcoci7873 I had no problem removing bolts but a lot of people saying that’s hard to get it out. If it is, then just unscrew 3 nuts on the top and that will help to get the bolts out.

Thank you!

It will work even when the needle is not working AS LONG AS YOUR AIR SYSTEM works, but this is not correct and I do not recommend driving like that because when your air system goes bad you might not know that, also it will lead to DOT out of service I believe!!!

What is your account on facebook buddy? How I can buy from you this part?

Will do soon in the next part.

High Amperage - Variable Voltage Power Supply kzbin.info/www/bejne/jpKcimqonpelmc0

I did it to stop the oil leak, so I can dry out area and put the seal. Plus, you can check the wheel bearing on the wheel.

Glad it was helpful!

DC Power Supply Variable, 30V 10A... www.amazon.com/dp/B0B7WBDXWN?ref=ppx_pop_mob_ap_share

Thank you so much

That cable with small alligator clamps came along with power supply. I bet you could find them on Amazon or Allixpress

a.co/d/3db8Wrx

Kenworth T680 AC compressor replacement. #kenworth kzbin.info/www/bejne/q2LIon5vjdCnjKM